Illumra ZBT-S1AWH User manual

Mounting
Commission (link) the switch to your system
before mounting.
The light switch is compatible with standard
decorator style faceplates.
A faceplate is included.
Surface Mount
For surface mount, attach included backplate
to the wall using screws or adhesive.
Flush Mount
For ush mount, mount the switch without the
backplate into a standard electrical switch box
using included screws.
AHD0611B
Decorator Style Battery-Free
ZigBee®Switch
ZBT-S1AWH (single rocker, white)
Overview
The Decorator Style Battery-Free ZigBee Switch
is a wireless transmitter that communicates
with a wide variety of ZigBee enabled
receivers. Every time the switch is pressed a
micro-generator produces a small electrical
current that powers a built-in transmitter. This
transmitter sends wireless radio signals that are
used to remotely control a receiver.
Compatible With
ZigBee Green Power
(included in ZigBee 3.0)
Lindon, UT• www.ILLUMRA.com • 801-349-1200
Specifications
ZBT-S1AWH Decorator Style Battery-Free ZigBee
Switch
Range 50-150 ft (typical)
Frequency 2.4 GHz (ZigBee channels 11-26)
Power Supply Self-generated when switch is pressed
Buttons 2 (1 rocker)
Dimensions 2.75 (W) x 4.5 (H) x 0.62 (D) inches
Operating
Temperature
-13º to +149º F
(-25º to 65º C)
Radio
Certications
Certied according to FCC, IC and CE
regulations
Addressing Factory Set Unique ID
Contains FCC ID: SVZ-PTM215Z
Contains IC: 5713A-PTM215Z
The enclosed device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (i.) this device may not cause harmful
interference and (ii.) this device must accept any interference received, including
interference that may cause undesired operation.
Always follow local electrical codes when installing this device. Installation should
be performed by a qualied electrician.
This device or certain aspects thereof is protected by at least one of the U.S. or
international patent or has at least one such patent application pending.

Commissioning
Part 1
Put your ZigBee Green Power compatible
controller system into commissioning (or
“linking”) mode.
If you don’t know how to do this, consult the
manual for your controller system or contact
the manufacturing company for assistance.
Part 2
Put your switch into commissioning mode.
To enter commissioning mode, start by selecting
one button on the switch. (Use the same button
for the entire sequence. Pressing any other
button will exit the commissioning mode.)
Next, execute the following long-short-long
sequence:
1.Press and hold the selected button for
more than 7 seconds before releasing it
2. Press the selected button quickly
(hold for less than 2 seconds)
3.Press and hold the selected button again
for more than 7 seconds before releasing it
Your switch has now entered commissioning
mode.
Cycle through the sixteen channels
To change the switch’s channel, press the
selected switch button shortly (less than 7
seconds) once after entering commissioning
mode. This will reset the channel used by the
switch to channel 11.
If the switch was already operating on
channel 11 (default condition) then the
radio channel will remain unchanged. This
ensures that the switch will always use
channel 11 as starting point for the channel
adjustment.
Press the selected button shortly (less
than 7 seconds) again to move to the next
channel. For each such button press, the
switch transmits on the next channel. If channel
26 has been reached then channel 11 will be
used next.
When your switch is on the correct
channel, your controller system will
indicate so by automatically exchanging a
security packet with the controller system.
There should be a visible exchange indicated
on your controller system, and your switch will
be linked to the system.
Exit linking mode on the switch by pressing
any other button on the switch.
For problems with the controller system, please
contact to your controller system provider.
Channel ID Lower
Frequency
Center
Frequency
Upper
Frequency
11 2404 2405 2406
12 2409 2410 2411
13 2414 2415 2516
14 2419 2420 2421
15 2424 2425 2426
16 2429 2430 2431
17 2434 2435 2436
18 2439 2440 2441
19 2444 2445 2446
20 2449 2450 2451
21 2454 2455 2456
22 2459 2460 2461
23 2464 2465 2466
24 2469 2479 2471
25 2474 2475 2476
26 2479 2480 2481
Part 3
Linking your switch to your controller system.
We need to send a radio signal from the switch to
the controller system on the correct ZigBee channel.
Your controller system uses one of sixteen possible
channels, automatically set by the controller
system. We will use the switch to send a signal on
each channel until we nd the channel used by your
controller system.
Upon entering commissioning mode, your switch
sent a signal on the currently selected channel.
The signal was sent on the default channel 11,
unless the switch has been put on another channel
previously. (This allows linking additional devices
without changing the currently used radio channel.)
Here is a chart of the ZigBee channels and the
corresponding radio frequencies (in MHz).