ILVE Fusion User manual

EN
Fusion
INSTALLATION, OPERATING AND MAINTENANCE GUIDE
220-240V / 50Hz
220-230V / 60Hz
395.502.1

2
EN

3
EN
Index
IGENERAL 4
II WARNINGS 5
III INSTALLATION 7
III.1 PRELIMINARY INDICATIONS 7
III.1.a AIR TREATMENT 9
III.2 INSTALLATION ON UP TO 660 mm DEEP BASES 10
III.2.a INDUCTION HOB INSTALLATION 11
III.2.b EXECUTIVE DIRECTIONS 13
III.3.c ASPIRATION UNIT ASSEMBLY 16
III.3 INSTALLATION ON UP TO 840mm DEEP BASES 18
III.3.a INDUCTION HOB INSTALLATION 21
III.3.b EXECUTIVE DIRECTIONS 23
III.3.c ASPIRATION UNIT ASSEMBLY 26
III.4 INSTALLATION ON UP TO 900mm DEEP BASES 28
III.4.a INDUCTION HOB INSTALLATION 29
III.4.b EXECUTIVE DIRECTIONS 31
III.4.c ASPIRATION UNIT ASSEMBLY 34
III.5 INSTALLATION ON BASES DEEP MORE THAN 900mm 36
III.5.a INDUCTION HOB INSTALLATION 39
III.5.b EXECUTIVE DIRECTIONS 41
III.5.c ASPIRATION UNIT ASSEMBLY 44
III.6 ELECTRICAL CONNECTION 46
IV OPERATION 49
V.1 INDUCTION HOB TECHNICAL FEATURES 49
V.2 APPROPRIATE POTS FOR INDUCTION 50
V.3 INDUCTION HOB OPERATION 51
V.4 COOKER HOOD OPERATION 63
VCLEANING AND MAINTENANCE 68
VI.1 INDUCTION HOB CLEANING 68
VI.2 COOKER HOOD CLEANING 70
VI TROUBLESHOOTING GUIDE 72
VII DISCONTINUATION, DISASSEMBLY AND WASTE DISPOSAL 74

4
EN
I GENERAL
This guide is intended for the consumer and describes the appliance and its use. This guide
is an integral part of the appliance itself and has to be retained with the appliance and
ALWAYS accompany it, even in case of its assignment to another owner or user or in case
the cooker hood is moved to another installation plant.
The aspiration system is composed by two appliances:
An induction hob;
An integrated cooker hood.
The two appliances are electrically and functionally independent and for this reason there
are two separated serial numbers and two Energy Labels.
Safety Warnings required for FUSION
• Metallic objects such as knives, forks, spoons and lids should not be
placed on the hotplate since they can get hot
• CAUTION – The cooking process has to be supervised. A short term
cooking process has to be supervised continuously.
• There is a risk of fire if cleaning is not carried out in accordance with the
instructions.
• Warning: Failure to install the screws or fixing devices in accordance
with the instructions may result in an electrical hazard.
The Manufacturer strives for continuous improvements.
For this reason, the text and illustrations in this guide may change without notice.

5
EN
II WARNINGS
ATTENTION: This appliance has not been designed for gas hobs.
•This appliance is manufactured according to the safety standards in force;
•The using of this appliance must not be other than the one it has been designed for, this means as
a domestic induction hob with integrated aspiration for cooking;
•The manufacturer does not accept any liability for damages caused by people, animals or things, by
installation and maintenance mistakes or by any illegitimate use.
Caution! Unattended cooking with fat or oil can be dangerous and
may result in fire. Be sure having the preparation of such food (fries)
under constant control.
Caution! Fire hazard: do not store items on the cooking surfaces.
Caution! Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
Caution! If the surface is cracked, switch off the appliance to avoid
the possibility of electric shock.
Caution! Before any cleaning or maintenance operation or in case of
storms, disconnect the appliance from the main power supply
(fig.2.1) or disconnect the plug (fig.2.2).
•Warning! Be careful not to drop objects or crockery on the glass surface. Even light objects (e.g. a
salt shaker) can crack or damage the ceramic plate.
•Warning! While the induction hob is active, even the aspiration parts adjacent to the induction hob
may become hot.
•There is a possibility of fire if the cleaning operations are not carried out as indicated in the
instructions.
•The appliance and its accessible parts become hot during use. Care should be taken to avoid touching
heating elements. Children less than 8 years of age shall be kept away unless continuously
supervised;
•Prevent the children to hang around the appliance and warn them properly against the danger of
burns;
Fig. 2.1
Fig. 2.2

6
EN
•This appliance can be used by children aged from 8 years and above, and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved;
•Children shall not play with the appliance;
•Cleaning and maintenance shall not be made by children without supervision;
•Don’t use high-pressure steam cleaner or hot steam to clean the appliance;
•It is forbidden to introduce any object in the aspiration flaps and air grids (fig.2.3).
•The appliance cannot be activated by external timers or remote controls systems;
•Do not use the appliance for room heating;
•If there is a wall power outlet located near the appliance and another appliance is plugged into it,
make sure the power cord does not come into contact with the hot cooking zones;
•Do not store any temperature-sensitive objects, materials, or substances underneath the appliance,
e.g. detergents, sprays, etc.
•In case of a failure of the appliance, immediately disconnect the appliance from the power mains
and contact the service center;
•Connect the appliance to a permanent connection;
•Don't connect the appliance to the power supply with an extension cable or multiple sockets,
because they don't assure a sufficient safety (e.g. overheating risk of multiple sockets);
•The appliance may be built-in and connected to the power supply only by a Qualified Technician;
•It is forbidden to pull, disconnect, twist the electrical wiring out of the appliance even if it is
disconnected from the power supply;
•Cooking zones may not be left in operation empty, without any dishes on top;
•Never use the glass surface as a working surface. Sharp objects may damage it;
•Preparation of food in aluminum or plastic cookware is not allowed. Never place any plastic objects
or aluminum foil upon the appliance surface;
•After using the appliance, disconnect it from the user’s interface. Do not trust the pot detector;
•Do not sprinkle or throw any water directly on the appliance;
•Do not flambé.
Fig. 2.3

7
EN
III INSTALLATION
III.1 PRELIMINARY INDICATIONS
Carefully read the guide before installation and use of the appliances.
The installation requires safety equipment and a range of tool as per fig.3.1.
The aspiration hob is equipped with all the hardware needed for its installation and is
suitable for most furniture.
Important: eventually, more screws than necessary for installation have been provided so
it is normal to have some left at the end of the installation.
Check minimum dimensions of the base requested for installation (Fig. 3.2). Minimum
height of the kitchen plinth is very important (min. 100 mm) in order to allow the passage
of the air ducts below the base of the furniture. Upon request, it is possible to purchase
a special kit for kitchen plinth up to 60 mm height.
Fig. 3.1
Fig. 3.2

8
EN
The furniture finishing should be treated with heat resistant glue (100°C) otherwise its
shape and colour may change due to the inferior heat resistance.
Ideally the appliance should be installed without any adjacent furniture or walls on both
sides (Fig.3.3-A). Furniture on only one side of the appliance is allowed (Fig.3.3-B
andFig.3.3-C). To prevent fire hazard it is strictly forbidden to install any furniture or
walls higher than the appliance on both sides (Fig.3.3-D).
Use of wood decoration plates or boards is not permitted
Minimum distance between the edge of the appliance and the furniture / wall is 250 mm
(Fig.3.4).
Fig. 3.3
Fig. 3.4

9
EN
On the front part there must be an opening of no less than 5 mm (Fig.3.5 dimension a).
It is recommended to install the appliance only after having installed the kitchen base
cabinet in order to avoid eventual damages to the glass hob.
III.1.a AIR TREATMENT
Questo dispositivo consente il trattamento dei fumi di cottura. Il sistema può essere
utilizzato in modalità aspirante o filtrante (kit filtri a carbone attivo o kit con filtro al
plasma fornibile separatamente).
Duct-out. The kitchen fumes are expelled outside through the pipe (not supplied
with the hood) connected to the engine exhaust fitting
Warning! The piping must never be connected to combustion
discharge pipes (stoves, boilers, burners, etc.)
The use of long pipes, with many bends, corrugated and with a diameter smaller than the
motor outlet’s will cause a decrease in extracting performance and a noise increase.
Filtering (recycling). The fumes pass through the active charcoal anti-odour
filter (not supplied with the hood) to be purifed and recycled in the kitchen.
Fig. 3.5
Fig. 3.5

10
EN
III.2 INSTALLATION ON UP TO 660 mm DEEP BASES
In the box the technician will find the elements shown on Fig. 3.6.
Elements must be mounted carefully following the procedure described in this guide.
The replacement fitting identified with "2" by a
marking on the back is not useful in this installation.
The device dimensions after installation are shown
at Fig. 3.7
The dimensions refer to the axis of the induction hob
and involve a specific configuration of the piece of
furniture, of the drawers that may be present and of
their own dimensions.
Fig. 3.7

11
EN
III.2.a INDUCTION HOB INSTALLATION
To leave the necessary space for the air pipes it is important to install the induction hob
with the centerline more than 300mm away from the wall on the back that may be
present.
Installation of the induction hob may be flush or non-flush.
NON-FLUSH INSTALLATION: Prepare the hole in the worktop as shown on Fig. 3.8.
FLUSH INSTALLATION: Prepare the hole in the worktop, mill the worktop along the entire
edge of the hole. Be sure to comply with the dimensions indicated on Fig. 3.9.
Fig. 3.8
Fig. 3.9

12
EN
Before fixing the induction hob fix the foam gasket provided with the appliance on the
back of the hob.
CAUTION! It is forbidden to install the appliance without the foam gasket!
Remove the protective film and fix the foam gasket at a 2 mm distance from the edge of
the glass (A=2mm), The gasket must be attached along the entire length and should not
overlap at the corners (Fig.3.10).
Lay in the silicon sealant flush with the hole (Fig. 3.11), along the milling and lay the hob
on (Fig.3.12)
Fig. 3.10
Fig. 3.11
Fig. 3.12

13
EN
III.2.b EXECUTIVE DIRECTIONS
The base of the cabinet must be at least drilled as indicated in Fig. 3.13 and the back
removed in case.
If the installation does not include the optional plasma filtering kit the cut of the base
can be reduced as shown at Fig. 3.14
Installation of the appliance imply a maximum length of the drawers that may be mounted
under the hob (Fig. 3.15)
•Drawers depth = 400mm about
•Last drawer depth = 300mm
Fig. 3.13
Fig. 3.14

14
EN
The next step is to determine the exit of the fumes according with the installation needs
(Fig. 3.16).
The air outlet can be rotated every 45 ° and thanks to the 15 ° fitting supplied with
the unit fitted in the two directions, it is possible to identify various configurations
for the outlet of the air duct.
To do this, you must cut the clamp that holds the power cable on the side of the
box, unscrew the screws that fix the octagonal box (Fig.3.17)
Fig. 3.15
Fig. 3.16

15
EN
Turn the motor (Fig.3.18) and position it in the desired direction. Once the container box
is positioned, assemble it with the previously removed screws. The rear or front output is
possible by connecting a special curve, not supplied.
Fig. 3.17
Fig. 3.18

16
EN
III.3.c ASPIRATION UNIT ASSEMBLY
After having determined the aspiration unit position, proceed by positioning it inside the
hole of the kitchen base previously cut (Fig. 3.13), making sure to recess the superior part
(Fig. 3.19-X) to the fix joint (Fig. 3.19-Y).
Proceed by fixing the cover to the vertical duct (Fig.3.20), using the special screws
included.
X
Y
Fig. 3.19
Fig.3.20

17
EN
It is now possible to joint up the external air exit for the fumes exhaust.
To place the exhaust pipe in the desired position it is necessary to buy spare joint pipes
not provided (Fig. 3.21).
All the pipes must pass under the base of the piece of furniture, inside the lift of the
kitchen plinth.
Fig. 3.21

18
EN
III.3 INSTALLATION ON UP TO 840mm DEEP BASES
For installation on bases deep up to 660 mm the only installation possible is described at
paragraph III.3.b.
For bases deep more than 660mm in addition to the previous configuration it is possible
to increase the space for the drawers by replacing joint flagged by “1” (label on the back)
with the one flagged by “2”.
Follow the installation procedure described hereunder.
The technician will find in the box the elements described at Fig. 3.6.
Fig. 3.6

19
EN
Remove the joint “1”
To carry this operation out it is necessary to remove the screws from the joint as
shown on Fig. 3.22 and 3.23
Fig. 3.22-a
Fig. 3.23

20
EN
It is now possible to assemble the joint “2” by fixing the 4 screws previously
removed. (Fig. 3.21 a-bn°1-3-4-5). Screws at Fig. 3.22 – 3.23 a-b n°2-6 must be
fixed after moving the inferior cover.
To move the inferior cover remove the 3 screws (Fig. 3.24 3-4-5). Move the cover
forward covering the empty space left by the new joint and fix the 3 screws at the
new position. Then fix the joint and the cover with the two remaining screws (Fig.
3.24 1-2)
Once the new joint is mounted the dimensions after complete installation will be the
ones shown at Fig. 3.25
Fig. 3.24
Fig. 3.25