Electrolux E48GC76EPS - 48" Sealed Burner Slide-In Gas... User manual

Installation Instructions
Slide In Gas Cooktop

Safety
(MPORTANTSAFETY(NSTRUCT(ONS
..............................................m [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] [] m [] []
))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))_i!i¸!!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii)
Safety Precautions
Do notattemptto install oroperateyour unit until you have readthesafety
precautions in this manual. Safety itemsthroughoutthis manual are labeled with a
Warning or Caution based onthe risktype.
Definitions
_Thisisthesafetyalertsymbol. Itisusedtoalertyoutopotentialpersonal
iniuiyhazards. Obeyallsafetymessagesthatfollowthissymboltoavoid possible
injuryordeath.

Safety 3
SAFETYPRECAUTIONS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
,,%,WARNING
•Read all instructions before using the appliance.
•Improper installation, adjustment, alteration, service, or maintenance can cause
personal injury or property damage. Refer to these instructions and the
accompanying Use & Care Manual. For assistance or additional information,
consult a qualified installer, service agency, manufacturer (dealer), or the gas
supplier.
•For your safety:
Do not obstruct the flow of combustion and ventilation air to the unit.
Keep appliance area clear and free from combustible material, gasoline and
other flammable vapors and liquids.
Do not use or attempt to use this appliance in the event of a power failure.
•This unit is designed as a cooking appliance. Never use it for warming or heating
aroom.
•This appliance must be installed with the gas pressure regulator supplied with it.
•Disconnect the electrical supply before installing or servicing the appliance.
•This appliance must be grounded. Connect only to a properly grounded
electrical supply. Refer to "Electrical Requirements".
•Install or locate this appliance only in accordance with these installation
instructions.
•Use this appliance only for its intended use as described in this manual. Do not
use corrosive chemicals or vapors in this appliance. This type of appliance is not
designed for industrial or laboratory use.
•As with any appliance, close supervision is necessary when used by children.
•Do not operate this appliance if it has a damaged electrical cord, plug, conduit or
wires, if it is not working properly, or if it has been damaged or dropped.
•This appliance should be installed and serviced only by qualified service
personnel.
•Some products, such as whole eggs, and sealed containers, such as closed glass
jars, may explode and should not be heated on this cooktop.

Safety

Finding Information
READANDSAVETHESEINSTRUCTIONS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
For toll-free telephone support in the U.S. and Canada:
1-877- 4ELECTROLUX (1-877-435-3287)
For online support and Internet product information:
www.electroluxusa.com
@2005 Eiectroiux Home Products, Inc.
Post Office Box 212378, Augusta, Georgia 30917, USA
All rights reserved. Printed in the USA

Finding Information
TABLEOFCONTENTS
Safety.....................................................................2
Definitions...........................................................2
ImportantSafetyInstructions...............................2
SafetyPrecautions .............................................. 3
Finding Information............................................5
PleaseReadAndSaveThisGuide....................5
Questions?..........................................................5
TableOfContents...............................................6
Preparing for Installation ...................................7
VerifyingPackageContents................................7
Cabinet/CounteropPreparation..........................7
MakingtheGaslElectricConnection...............11
Requirements...................................................11
L,P,GasConversion........................................12
Installation ..........................................................14
...........................................................................................................................InstallingtheCooktop........................................14
ConnectingtheGas..........................................14
GasandElectricRequirementsTable...............15
InstallingtheBurnerComponents.....................16
MakingtheElectricalConnection......................17
Operation............................................................18
VerifyingtheOperation......................................18

PreparingforInstallation
VERIFYPACKAGECONTENTS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
• Literature Pack
• Bolts/Washers
• Burner Grate Pack
• Burner Set
• Gas Pressure Regulator
• Burner Cap Pack
• Griddle
• Simmer Plate
• Wok Stand
• Stainless Steel Cleaner
• LP Conversion Kit
[] [] [] [] [] []
CABINET/COUNTER'FOPPREPARATION
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
The installation of this built-in appliance must be completed by a qualified appliance
technician or contractor. Proper installation is the owner's responsibility.
Carefully check the location where the cooktop is to be installed. The cooktop
should be placed for convenient access, but away from drafts that may be caused
by open doors and windows or by HVAC duct outlets. Make certain that gas and
electrical power can be provided in the selected locations. Plan the installation so
that all minimum clearances are met or exceeded. Dimensions shown provide
minimum clearances, unless otherwise noted.

Preparing for Installation
Figure 1
Plan the installation so that the electrical connection, gas shut-off valve, and
pressure regulator are accessible from the front of the cabinet and so that all of the
E36GC76EPS: 36" (914mm) Minimum
E48GC76EPS: 48" (1219mm) Minimum
Hood
Min to 5,8" (16turn) Overhar_g, both sides
combustib]e side / _,2" (38ram)
wall both sides Typical Cour_te_op
Q ®
• ® ® •
6 I
E48GC76EPS 30" (762mm)
V
...... 30" {762turn)
Minimum
/8" J
(457mm}
1
7 3_4" ]
H97mm)
-- (g14mm)
/5 1_2rr
(393mm) 28 /4"
(7/7mm)
/0" J
/254mm)
T
minimum required
dimensions are provided.
Dimensions apply to both
models unless otherwise
stated (see Figure 1). Locate
the electrical supply box
within reach of the included
48 inch long flexible cord so
the connection is accessible
when the cooktop is in place.

PreparingforInstallation
Figure 3 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Countertop Cut-out Dimensions
(when Cooktop is to be installed with Downdraft Vent Hood
36" model: E36DD75ESS; 48" model: E48DD75SS)
Vertical
non-combustible
surface rear wall .,_ E36GC76EPS-33 7/8" (860mm) I_
"_. _ E48GC76EPS - 43 1/2" (1105mm) z _['_-. Backsplash
_1 _ I i I Max.3/4" (19ram) _--_,
/ = Ii / _[--]213/_+; ,
........ I i21 3/8" Ii / /'_ 1_7_mm i
...... (543mm) Ii | 1/4" (6mm) ",, _ t "_
(716r_m) I i I Ii / Min. flatledge _ T I i ,,"
3" (76ram)
-- _ _E36 GC76EPS-34 3/4'+ (883mm)/ I
5/8" (16ram) E48GC76EPS- 46 3/4" (1188mm) --_
'_-_ E36GC76EPS - 36" (914rnm) _ _._ 6'+ (152mm) Min.
E48GC76EPS - 48" (1219mm) to combustible side
Figure 4 walls above the range
(both sides)
iiiiiiiiiiii

Preparing for Installation
OPTIONAL STAINLESS
STEEL BACKSPLASH
ACCBGO9 a6SI
Ea6GC76EPS: ACCBD09 4SS_
E#SDC76EPS:
Overall Dimensions - Side Views
Clearance to Combustible Rear Wall
COMBUSTIBLE REAR
FWALL MATERIAL
TOP OF FINISHED COUNTER_
743E197mm]
2½Ee4r_m]
Figure 5
Optional 9" stainless
steel backsplash
(attaches to wall) /
Side inset s/8"
Overall Dimensions
Cutout Dimensions _ ............. _:_
Clearance to Combusti
10" min. to nearest
combustible wall
(either side of unit)
2 W' min. required distance
between rearedgeofcooktop
andnearest combustible
surface abovecountertop.*
I,_3 Y2"
Suppo_
pla_orm
t/2" typical
countertop
edge
Openingtoroutegas /
andelectricalsupply
*If 2 W' clearance can not be maintained, then optional
stainless steel backsplash or noncombustible backsplash
material must be used - otherwise this installation
will require custom cabinet and countertop dimensions.
Figure 6
Dimensions
Cooktop Model A B C D
E48GC76EPS 48" Min. 48" 46" 48"
E36GC76EPS 36" Min. 36" 34sA'' 36"

Makingthe Gas/ElectricConnection
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
GasSupplyRequirements
Check your local building codes for the proper method of installation. In the
absence of local codes, this appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54. Be certain that the appliance being
installed is correct for the gas service being provided. Refer to the data plate
located on the bottom of the cooktop chassis.

Makingthe Gas/ElectricConnection
LiQU(FIEDPETROLEUM(PROPANE)GASCONVERS(ON
This appliance can be used with Natural Gas and Propane Gas. It is shipped from
the factory for use with natural gas.
A kit for converting to LP gas is supplied with your cooktop. The kit is marked "FOR
LP/PROPANE GAS CONVERSION". Follow the installation instructions which are
inside the envelope.
The conversion must be performed by a qualified service technician in
accordance with the kit instructions and all local codes and requirements.
Failure to follow instructions could result in serious injury or property
damage. The qualified agency performing this work assumes responsibility
for the conversion.

Making the Gas/Electric Connection i
iiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
ElectricalSupplyRequirements iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
The correctvoltage, frequencyand amperage mustbe suppliedtothe appliance iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
from an isolated, groundedcircuitwhich isprotectedbyaproperlysizedcircuit iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
breakerortime-delayfuse, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_
Thecooktopmustbeconnectedtothepowersupplywithcopperwireonly. The iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
use of aluminum wire may result in unsatisfactoryconnections. Flexible armored or iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
nonmetallic, sheathedcoppercable(withagroundingwire) shouldbeusedto iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
supplyelectricalpowertothejunctionboxorreceptacle, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
The cooktop'sfactory-equipped, three-prong grounding plug mustbe inserted into a iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
matinggrounding-type receptacle inaccordancewith National ElectricCodeand iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
applicablestate, municipalandlocalcodes, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Becertaintolocatethejunctionboxorelectricaloutletsotheelectricalsupplymay iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
be easilydisconnected inthe eventthatservice becomes necessary. Also, provide iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
extraslackinthecabletoallowthecooktoptoberemovedforservicing, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_

Installation
INSTALLINGTHECOOKTOP
m [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] [] m [] []
Place and center the cooktop within the cutout. Secure the cooktop to the
countertop utilizing the two (2) 1/4-20 bolts provided. Do not overtighten the
screws.
CONNECTINGTHEGAS
m m [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Attach the gas pressure regulator (included with the cooktop) to cooktop pipe nipple
inlet.
Install a gas shut-off valve (not included with the cooktop) in the main gas supply
line in an accessible location near the cooktop. Complete connection of the gas
supply to the cooktop by installing 1/2 inch flexible gas line (not included with the
cooktop) between the pressure regulator and the shut-off valve.

Installation
GASAND ELECTR(CREQU(REMENTSTABLE
[] [] [] [] [] [] Bll [] [] [] [] [] [] [] [] Bll [] [] [] [] []
The required voltage, frequency and amperage ratings are listed on the product
data plate outside on the cooktop bottom. The gas and electric requirements are
also shown in the table below.
Model No.
E36GC76EPS
E48GC76EPS
Electrical
circuit
required
120VAC,
60Hz, 15A
Total
connected
load
0.7 Amps
(0.084 Kw)
Gas type
Natural
Liquid Propane
Natural
Liquid Propane
Manifold
pressure
4" Water Column
10" Water Column
4" Water Column
10" Water Column
Minimum gas
supply
pressure
5" Water Column
11" Water Column
5" Water Column
11" Water Column
((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((,_
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_

Installation
(NSTALUNGTHEBURNERCOMPONENTS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
BurnerComponents
Remove the brass burner rings, porcelain burner caps, and porcelain grates from
their shipping packages. Place each burner ring onto its corresponding burner
base, being certain that the four alignment tabs slide into the matching notches in
the base. Set each porcelain burner cap on top of its corresponding burner ring.
Place each grate onto the cooktop, being certain that the rubber feet are positioned
in the locating dimples.
Figure 7
Grate
J
Burner Cap
Burner Ring
J
/Top Frame
........... Burner Head (Fixed)
Burner Components

Installation
MAK(NGTHEELECTR(CALCONNECT(ON
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Plug the three-prong plug from the appliance into the properly grounded and
polarized wall receptacle.

Operation
VER(FY(NGTHEOPERAT(ON
..............................................m m [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Before beginning the test procedure, ensure that the gas supply is turned off at the
shut-off valve, all cooktop control valves are in the "OFF" position, and all burner
rings, burner caps, and grates are properly positioned on the cooktop.
Rotate one knob at a time counterclockwise to the "LITE/Hr' position. Verify that all
ignitors spark continuously, then return the knob to the "OFF" position. Repeat for
all knobs. See Figure 8.
Figure 8
Burner Control Valve

Operation
Turn on the main gas supply to the cooktop by opening the gas shut-off valve. Test
each burner separately by pressing and turning one control knob at a time
counterclockwise to the "LITE/Hr' position. All ignitors will spark simultaneously. (It
will take approximately four seconds for ignition to occur, at which time all igniters
will stop sparking. If ignition does not occur within four seconds, turn off the knob,
wait for at least five (5) minutes to allow any gas to dissipate, then repeat this
ignition test.) The control knob can then be rotated counterclockwise from "HI" to
"LOW" to adjust the flame height progressively. Repeat the ignition test for all
burners.
When installed properly, the flame will be steady and quiet. It will also have a sharp,
blue inner cone that will vary in length proportional to the burner size. Flame
adjustment will not be necessary.
Read and understand the accompanying Use & Care Manual prior to cooking with
this appliance. The Use & Care Manual contains additional important safety,
service and warranty information.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ii !i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iii