IMI TA TA-FUS1ON-C User manual

TA-FUS1ON-C
Combined control & balancing
valves
With independent EQM
characteristics

IMI TA / Control valves / TA-FUS1ON-C
2
TA-FUS1ON-C
These innovative balancing and control valves for heating and cooling
systems combine the key hydronic functions of balancing and control in
one valve. Adjustable Kvs and inherent independent EQM characteristics
allow correct valve sizing and optimum system controllability. The
measuring points enable accurate measurement of flow, dierential
pressure, temperature and available dierential pressure.
Key features
> Adjustable Kvs
Allows correct Kvs setting
corresponding to system
requirements.
> Independent, inherent EQM
characteristic
Proper EQM valve characteristic for all
settings.
> Self-sealing measuring points
Simple and accurate measurement for
balancing, trouble shooting and power
measurement.
> Actuators
Valves and actuators supplied together
ensuring optimum control performance
and simplified selection.
Technical description – Valve
Application:
Heating and cooling systems.
Functions:
Control (EQM)
Balancing
Pre-setting (Kvs)
Measuring (ΔpV, ΔH, T, q)
Shut-o (for isolation during system
maintenance)
Dimension:
DN 32-150
Pressure class:
DN 32-50: PN 16
DN 65-150: PN 16 and PN 25
Max. dierential pressure (ΔpVmax):
400 kPa = 4 bar
ΔpVmax = The maximum allowed pressure
drop over the valve, to fulfill all stated
performances.
Recommended setting range (Kvmax):
DN 32: 2,68 - 12,9
DN 40: 3,03 - 18,5
DN 50: 8,03 - 33,0
DN 65-2: 24,3 - 64,3
DN 80-2: 38,1 - 100
DN 100: 57,4 - 160
DN 125: 97,4 - 270
DN 150: 146 - 400
Kvmax = m³/h at a pressure drop of 1 bar
at each setting and fully open valve plug.
Lift:
20 mm
Rangeability:
>100 (for all recommended settings)
Leakage rate:
Tight sealing
Characteristics:
Independent EQM.
Temperature:
Max. working temperature: 120°C
Min. working temperature: -20°C
Media:
Water or neutral fluids, water-glycol
mixtures.
(For other media contact IMI Hydronic
Engineering.)
Material:
DN 32-50:
Valve body: AMETAL®
Valve plug: AMETAL®
Seat seal: EPDM/Stainless steel
Spindle seal: EPDM O-ring
O-rings: EPDM
Valve insert: AMETAL®/PPS/PTFE
Springs: Stainless steel
Spindle: Stainless steel
DN 65-150:
Valve body: Ductile iron EN-GJS-400
Valve plug: Stainless steel
Seat seal: EPDM/Stainless steel
O-rings: EPDM
Plug mechanism: Stainless steel and
brass
Screws and nuts: Stainless steel
AMETAL®is the dezincification resistant
alloy of IMI Hydronic Engineering.

3
Surface treatment:
DN 32-50: Non treated
DN 65-150: Electrophoretic painting.
Marking:
DN 32-50: TAH, IMI, DN, PN, DR, serial No and flow direction
arrow.
DN 65-150: TAH, IMI, DN, PN, Kvs, Tmin/max, serial number, valve
body material and flow direction arrow, label.
CE-marking:
DN 65-125: CE
DN 150: CE 0062 *
*) Notified body.
Connection:
DN 32-50:
Female thread according to ISO 228. Thread length according
to ISO 7-1.
Male thread according to ISO 228.
DN 65-150:
Flanges according to EN-1092-2, type 21. Face to face length
according to EN 558 series 3.
Valve characteristics
Nominal valve characteristic for all recommended settings.
Measuring accuracy
Maximum flow deviation at dierent settings
DN 32-50 DN 65-150
*) Setting (%) of fully open valve.
0
10
20
30
40
50
60
70
80
90
100
0102030405060708090
100
h [%
]
Kv/Kv
max
[%]
0
2
4
6
8
10
12
14
16
20 30 40 50 60 70 80 90 10
0 *)
18
±[%]
100
0
2
4
6
8
10
12
14
16
20 30 40 50 60 70 80 90 100 *)
18
±[%]
100

IMI TA / Control valves / TA-FUS1ON-C
4
Correction factors
The flow calculations are valid for water (+20°C). For other
liquids with approximately the same viscosity as water
(≤20 cSt = 3°E=100S.U.), it is only necessary to compensate for
the specific density. However, at low temperatures, the viscosity
increases and laminar flow may occur in the valves. This causes
a flow deviation that increases with small valves, low settings
and low dierential pressures. Correction for this deviation can
be made with the software HySelect or directly in our balancing
instruments.
Noise
In order to avoid noise in the installation the flows must be
correctly balanced and the water de-aerated.
Very high dierential pressures can cause noise in the
installations, and in that case, dierential pressure controllers
should be used.
The maximum recommended pressure drop in order to avoid
excessive noise is 200 kPa.
Actuators
A wide range of high performance proportional actuators are
available from IMI Hydronic Engineering (e.g. 24V, 100-240V,
230V, fail safe) to provide accurate modulating or 3-point
control, when used together with combined balancing and
control valves. See “Selection tables”.
For more details on actuators, see separate technical leaflets or
contact IMI Hydronic Engineering.
Sizing
When ΔpV and flow are known, use the formula to calculate
Kvmax.
Example
Flow is 10 m3/h, ΔpV is 35 kPa and control signal (input signal)
0-10 VDC.
1. Go to sizing diagram. (When calculating the Kvmax by the
formula go directly to step 4).
2. Draw a straight line between 10 m3/h and 35 kPa.
3. Read the needed Kvmax value where the line crosses the Kv-
axis. In this case Kvmax=16,9.
4. Draw a horizontal line from Kvmax 16,9, which will cross the
setting bars for all valves which fit the application. In this case
DN 40 setting 9,5, DN 50 setting 5,0.
5. Choose the smallest option (with some safety margin). In this
case DN 50 is preferable.
6. Go to the selection tables to select the correct valve and
actuator combination. In this case article number
322205-50911 (24 V).
Note
If the required flow falls outside the scale of the diagram, the
reading can be made as follows: Use the design ΔpV and draw
the line to a flow that is 0,1 or 10 times the design flow, getting
Kvmax in the same relation (either 0,1 or 10 times needed).
Following the previous example
35 kPa and 10 m3/h gives Kvmax=16,9
35 kPa and 1 m3/h gives Kvmax=1,69
35 kPa and 100 m3/h gives Kvmax=169

5
Sizing diagram
DN 65-150: Recommended setting range 7.5–10 (≈40–100% of Kvs).

IMI TA / Control valves / TA-FUS1ON-C
6
Selection tables
Maximum recommended pressure drop (ΔpV) for valve
and actuator combination
The maximum recommneded pressure drop over the valve and
actuator combination for close o (ΔpVclose) and to fulfill all stated
performances (ΔpVmax). For detailed information on maximum
closing o pressure, see “Closing force”.
ΔpVclose = The maximum pressure drop that the valve can
close against from an opened position, with a specified force
(actuator) without exceeding stated leakage rate.
ΔpVmax = The maximum allowed pressure drop over the valve, to
fulfill all stated performances.
DN TA-Slider
750
TA-Slider
1250
TA-MC100
FSE/FSR
[kPa] [kPa] [kPa]
32 400 – 400
40 400 – 400
50 400 – 400
65 400 – 400
80 400 – 400
100 400 – 400
125 400 – 400
150 200 400 400
The codes in the selection tables are for dierent sets of valve
size (DN) and type of actuator. Valves and actuators supplied
together ensures optimum control and simplified selection. For
other combinations order valve and actuator separately, see
“Articles – Valves” and “Articles – Actuators”.
For more details on actuators, see separate technical leaflets or
contact IMI Hydronic Engineering.
Article number: 322205-xxxxx / 22106-xxxxxx
To get the complete article number, simply add the code stated
below according to your required set.
Example: 322205-50711
With standard actuators
TA-Slider 750 TA-Slider 750 TA-Slider 1250 TA-Slider 1250
Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point, on-o
Output signal: 0(2)-10 VDC
Supply voltage: 24 VAC/VDC 100-240 VAC 24 VAC/VDC 100-240 VAC
Fail safe: No
DN PN Kvs 322205-
32 16 12,9 50711 50721 – –
40 16 18,5 50811 50821 – –
50 16 33,0 50911 50921 – –
65-2 16 64,3 51011 51021 – –
65-2 25 64,3 61011 61021 – –
80-2 16 100 51111 51121 – –
80-2 25 100 61111 61121 – –
100 16 160 51211 51221 – –
100 25 160 61211 61221 – –
125 16 270 51311 51321 – –
125 25 270 61311 61321 – –
150 16 400 – – 51431 51441
150 25 400 – – 61431 61441
DN 32-50: Female threaded
DN 65-150: Flanged

7
With fail safe actuators
TA-MC100FSE TA-MC100FSE TA-MC100FSR TA-MC100FSR
Input signal: 0(2)-10 VDC, 0(4)-20 mA,
3-point 3-point 0(2)-10 VDC, 0(4)-20 mA,
3-point 3-point
Output signal: 0(2)-10 VDC, 0(4)-20 mA 0-10 VDC 0(2)-10 VDC, 0(4)-20 mA 0-10 VDC
Supply voltage: 24 VAC 230 VAC 24 VAC 230 VAC
Fail safe: Extending (closing) Retracting (opening)
DN PN Kvs 22106-
32 16 12,9 081032 101032 091032 111032
40 16 18,5 081040 101040 091040 111040
50 16 33,0 081050 101050 091050 111050
65-2 16 64,3 082065 102065 092065 112065
65-2 25 64,3 083065 103065 093065 113065
80-2 16 100 082080 102080 092080 112080
80-2 25 100 083080 103080 093080 113080
100 16 160 082100 102100 092100 112100
100 25 160 083100 103100 093100 113100
125 16 270 082125 102125 092125 112125
125 25 270 083125 103125 093125 113125
150 16 400 082150 102150 092150 112150
150 25 400 083150 103150 093150 113150
DN 32-50: Female threaded
DN 65-150: Flanged
Kvmax values
Positions
12345678910
DN 32 2,68 3,15 3,75 4,45 5,37 6,51 7,93 9,55 11,1 12,9
DN 40 3,03 3,63 4,53 5,70 7,07 8,88 11,1 13,0 15,4 18,5
DN 50 8,03 9,74 11,9 14,4 17,0 20,0 23,3 27,3 30,4 33,0
Positions
5.5 6 6.5 77.5 88.5 99.5 10
DN 65-2 12,6 14,9 17,6 20,6 24,3 28,8 34,5 41,8 51,4 64,3
DN 80-2 19,8 23,2 27,4 32,2 38,1 45,2 54,5 65,9 81,2 100
DN 100 29,1 34,5 40,9 48,4 57,4 68,6 82,6 101 125 160
DN 125 49,5 58,6 69,4 82,1 97,4 116 140 170 212 270
DN 150 74,5 88,1 104 123 146 173 208 253 314 400
DN 65-150: Recommended setting range 7.5–10 (≈40–100% of Kvs).
Kvmax = m³/h at a pressure drop of 1 bar at each setting and fully open valve plug.

IMI TA / Control valves / TA-FUS1ON-C
8
Closing force
Necessary force (F) to close the valve versus the dierential pressure (ΔpVclose), without exceeding stated leakage rate.
ΔpVclose = The maximum pressure drop that the valve can close against from an opened position, with a specified force (actuator)
without exceeding stated leakage rate.
ΔpVmax = The maximum allowed pressure drop over the valve, to fulfill all stated performances.
F [N]
∆pV
Close
[k
Pa]
0
100
200
300
400
500
600
700
800
300400 500600 700800 900100011001200
DN 80 65 100 32-50 125 150
1300
∆pVma
x
TA-Slider 750
TA-Slider 1250
TA-MC100FSE/FSR

9
Installation
Application examples
2-way direct circuit
Injection circuit
Normal pipe fittings
Avoid mounting taps and pumps immediately before or after the
valve.
Installation recommendation for accurate measurement due to
distortion of fully developed turbulent flow profile.
Flow direction
DN 32-50 DN 65-150
Installation of actuator
Approx. 140 mm of free space is required above the actuator.
Ingress protection
IP54
Note: Read carefully the installation instruction of the actuator.
TA-Slider 750/TA-Slider 1250
TA-MC100 FSE/FSR
TA-FUSION-C
TA-FUSION-C
2D 2D5D 10D
>140
>140
DN 32-50
DN 65-150
DN 32-50
DN 65-150

IMI TA / Control valves / TA-FUS1ON-C
10
Operating function DN 32-50
Setting
1. Open the valve fully with the handwheel.
2. Press the handwheel downwards and turn to desired value,
e.g. 5.3.
Shut-o
1. Turn the handwheel to “Closed”.
Turn the handwheel to “Open” when re-opening the valve.
Measuring ΔpV and q
Connect IMI Hydronic Engineering balancing instrument to the
measuring points. Input the valve type, size and setting and the
actual flow is displayed.
Measuring ΔH
Connect IMI Hydronic Engineering balancing instrument to the
measuring points. Close the valve according to “Shut-o” and
measure. Important! The valve must be re-opened fully after
the measurement is completed.
NOTE!
Ensure that the actuator is disengaged from the valve spindle
during all operating functions described above.
Operating function DN 65-150
Setting
1. Release the fixing nut.
2. Turn the setting screw to desired value on the scale, e.g. 9.2.
3. Tighten the fixing nut.
Shut-o
1. Release the fixing nut.
2. Turn the setting screw clockwise to stop (position 0 ±0.5).
The presetting is visible on the setting scale.
3. Tighten the fixing nut.
Open to previous setting when re-opening the valve.
Measuring ΔpV and q
Connect IMI Hydronic Engineering balancing instrument to the
measuring points. Input the valve type, size and setting and the
actual flow is displayed.
Measuring ΔH
Connect IMI Hydronic Engineering balancing instrument to the
measuring points. Close the valve according to “Shut-o” and
measure.
Important! The valve must be re-opened to previous setting
after the measurement is completed.
NOTE!
Ensure that the actuator is disengaged from the valve spindle
during all operating functions described above.
∆H
∆pV
∆H
∆pV

11
Articles – Sets
DN 32-50 Female threads Threads according to ISO 228
TA-Slider 750 Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point, on-o
24 VAC/VDC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 351 209 186 361 12,9 5,1 5902276884603 322205-50711
40 G1 1/2 128 159 351 209 186 361 18,5 5,2 5902276884665 322205-50811
50 G2 128 167 356 209 190 365 33,0 5,7 5902276884726 322205-50911
100-240 VAC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 351 209 186 361 12,9 5,1 5902276884634 322205-50721
40 G1 1/2 128 159 351 209 186 361 18,5 5,2 5902276884696 322205-50821
50 G2 128 167 356 209 190 365 33,0 5,7 5902276884757 322205-50921
DN 65-80 With flanges Flanges according to EN-1092-2, type 21.
TA-Slider 750 Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point, on-o
24 VAC/VDC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 401 64,3 19 5902276884788 322205-51011
80-2 200 203 205 401 100 23 5902276884801 322205-51111
PN 25
65-2 185 190 205 401 64,3 19 5902276884887 322205-61011
80-2 200 203 205 401 100 23 5902276884900 322205-61111
100-240 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 401 64,3 19 5902276884795 322205-51021
80-2 200 203 205 401 100 23 5902276884818 322205-51121
PN 25
65-2 185 190 205 401 64,3 19 5902276884894 322205-61021
80-2 200 203 205 401 100 23 5902276884917 322205-61121
*) Height to the spindle top.
→= Flow direction
For maximum ΔpVclose, see “Selection tables”.
Valve and actuator are individually packaged for easy handling on site.
ØD1
d
L2
L1
H1*
H2
>140
L3
>140

IMI TA / Control valves / TA-FUS1ON-C
12
DN 100-150 With flanges Flanges according to EN-1092-2, type 21.
TA-Slider 750 / TA-Slider 1250 (DN 150) Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point, on-o
24 VAC/VDC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
100 220 229 221 403 160 29 5902276893193 322205-51211
125 250 254 221 403 270 39 5902276893209 322205-51311
150 285 267 251 420 400 52 5902276884863 322205-51431
PN 25
100 235 229 221 403 160 29 5902276893216 322205-61211
125 270 254 221 403 270 39 5902276893223 322205-61311
150 300 267 251 420 400 52 5902276893230 322205-61431
100-240 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
100 220 229 221 403 160 29 5902276893247 322205-51221
125 250 254 221 403 270 39 5902276893254 322205-51321
150 285 267 251 420 400 52 5902276884870 322205-51441
PN 25
100 235 229 221 403 160 29 5902276893261 322205-61221
125 270 254 221 403 270 39 5902276893278 322205-61321
150 300 267 251 420 400 52 5902276893285 322205-61441
*) Height to the spindle top.
→= Flow direction
For maximum ΔpVclose, see “Selection tables”.
Valve and actuator are individually packaged for easy handling on site.
>140
L
ØD
H2
H1

13
Articles – Fail-safe sets, extending (closing)
DN 32-50 Female threads Threads according to ISO 228
TA-MC100FSE Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point
24 VAC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 319 141 186 356 12,9 6,2 5901688820162 22106-081032
40 G1 1/2 128 159 319 141 186 356 18,5 6,3 5901688820209 22106-081040
50 G2 128 167 324 141 190 360 33,0 6,8 5901688820247 22106-081050
230 VAC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 319 141 186 356 12,9 6,2 5901688820186 22106-101032
40 G1 1/2 128 159 319 141 186 356 18,5 6,3 5901688820223 22106-101040
50 G2 128 167 324 141 190 360 33,0 6,8 5901688820261 22106-101050
DN 65-150 With flanges Flanges according to EN-1092-2, type 21.
TA-MC100FSE Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point
24 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 382 64,3 20 5901688820629 22106-082065
80-2 200 203 205 382 100 24 5901688820742 22106-082080
100 220 229 221 387 160 30 5901688821046 22106-082100
125 250 254 221 387 270 40 5901688821169 22106-082125
150 285 267 251 407 400 55 5901688823637 22106-082150
PN 25
65-2 185 190 205 382 64,3 20 5901688820667 22106-083065
80-2 200 203 205 382 100 24 5901688820780 22106-083080
100 235 229 221 387 160 30 5901688821084 22106-083100
125 270 254 221 387 270 40 5901688821206 22106-083125
150 300 267 251 404 400 55 5901688823644 22106-083150
230 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 382 64,3 20 5901688820643 22106-102065
80-2 200 203 205 382 100 24 5901688820766 22106-102080
100 220 229 221 387 160 30 5901688821060 22106-102100
125 250 254 221 387 270 40 5901688821183 22106-102125
150 285 267 251 404 400 55 5901688823675 22106-102150
PN 25
65-2 185 190 205 382 64,3 20 5901688820681 22106-103065
80-2 200 203 205 382 100 24 5901688820803 22106-103080
100 235 229 221 387 160 30 5901688821107 22106-103100
125 270 254 221 387 270 40 5901688821220 22106-103125
150 300 267 251 404 400 55 5901688823682 22106-103150
→= Flow direction
*) Height to the spindle top.
For maximum ΔpVclose, see “Selection tables”.
Valve and actuator are individually packaged for easy handling on site.
L1
L2
ØD1
d
H2
>140
H1*
L3
>140
L
ØD
H2
H1

IMI TA / Control valves / TA-FUS1ON-C
14
Articles – Fail-safe sets, retracting (opening)
DN 32-50 Female threads Threads according to ISO 228
TA-MC100FSR Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point
24 VAC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 319 141 186 356 12,9 6,2 5901688820179 22106-091032
40 G1 1/2 128 159 319 141 186 356 18,5 6,3 5901688820216 22106-091040
50 G2 128 167 324 141 190 360 33,0 6,8 5901688820254 22106-091050
230 VAC
DN d D1 L1 L2 L3 H1* H2 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 319 141 186 356 12,9 6,2 5901688820193 22106-111032
40 G1 1/2 128 159 319 141 186 356 18,5 6,3 5901688820230 22106-111040
50 G2 128 167 324 141 190 360 33,0 6,8 5901688820278 22106-111050
DN 65-150 With flanges Flanges according to EN-1092-2, type 21.
TA-MC100FSR Input signal: 0(2)-10 VDC, 0(4)-20 mA, 3-point
24 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 382 64,3 20 5901688820636 22106-092065
80-2 200 203 205 382 100 24 5901688820759 22106-092080
100 220 229 221 387 160 30 5901688821053 22106-092100
125 250 254 221 387 270 40 5901688821176 22106-092125
150 285 267 251 404 400 55 5901688823651 22106-092150
PN 25
65-2 185 190 205 382 64,3 20 5901688820674 22106-093065
80-2 200 203 205 382 100 24 5901688820797 22106-093080
100 235 229 221 387 160 30 5901688821091 22106-093100
125 270 254 221 387 270 40 5901688821213 22106-093125
150 300 267 251 404 400 55 5901688823668 22106-093150
230 VAC
DN D L H1* H2 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 382 64,3 20 5901688820650 22106-112065
80-2 200 203 205 382 100 24 5901688820773 22106-112080
100 220 229 221 387 160 30 5901688821077 22106-112100
125 250 254 221 387 270 40 5901688821190 22106-112125
150 285 267 251 404 400 55 5901688823699 22106-112150
PN 25
65-2 185 190 205 382 64,3 20 5901688820698 22106-113065
80-2 200 203 205 382 100 24 5901688820810 22106-113080
100 235 229 221 387 160 30 5901688821114 22106-113100
125 270 254 221 387 270 40 5901688821237 22106-113125
150 300 267 251 404 400 55 5901688823705 22106-113150
→= Flow direction
*) Height to the spindle top.
For maximum ΔpVclose, see “Selection tables”.
Valve and actuator are individually packaged for easy handling on site.
L1
L2
ØD1
d
H2
>140
H1*
L3
>140
L
ØD
H2
H1

15
Articles – Valves
Female thread
Threads according to ISO 228
DN d D1 L1 H1 Kvs Kg EAN Article No
PN 16
32 G1 1/4 128 153 186 12,9 3,5 7318798639207 22106-001032
40 G1 1/2 128 159 186 18,5 3,6 7318798639306 22106-001040
50 G2 128 167 190 33,0 4,1 7318798639405 22106-001050
Male thread
Threads according to ISO 228
DN d D1 L1 H1 Kvs Kg EAN Article No
PN 16
32 G1 1/2 128 213 186 12,9 4,1 7318794015906 22106-005032
40 G2 128 221 186 18,5 4,2 7318794016002 22106-005040
50 G2 1/2 128 235 190 33,0 5,1 7318794016101 22106-005050
Flanged
Flanges according to EN-1092-2, type 21.
DN D L H1 Kvs Kg EAN Article No
PN 16
65-2 185 190 205 64,3 17 5901688827529 22106-002065
80-2 200 203 205 100 21 5901688827550 22106-002080
100 220 229 221 160 27 3831112527881 22106-002100
125 250 254 221 270 37 3831112527911 22106-002125
150 285 267 251 400 50 3831112527942 22106-002150
PN 25
65-2 185 190 205 64,3 17 5901688827536 22106-003065
80-2 200 203 205 100 21 5901688827567 22106-003080
100 235 229 221 160 27 3831112527898 22106-003100
125 270 254 221 270 37 3831112527928 22106-003125
150 300 267 251 400 50 3831112527959 22106-003150
→= Flow direction
L1
H1
d
ØD1
L1
H1
d
ØD1
ØD
H1
L

IMI TA / Control valves / TA-FUS1ON-C
16
Articles – Actuators
TA-Slider 750, TA-Slider 1250, TA-MC100FSE/FSR
(Available as sets with TA-FUSION)
For more details on actuators, see separate technical leaflets or contact IMI Hydronic Engineering.
Type Supply voltage EAN Article No
TA-Slider 750 24 VAC/VDC 5901688828458 322226-10110
TA-Slider 750 100-240 VAC 5902276883620 322226-40110
TA-Slider 1250 24 VAC/VDC 5901688828533 322227-10110
TA-Slider 1250 100-240 VAC 5902276883828 322227-40110
TA-MC100FSE 24 VAC 3831112512122 61-100-101
TA-MC100FSE 230 VAC 3831112512139 61-100-102
TA-MC100FSR 24 VAC 3831112512146 61-100-201
TA-MC100FSR 230 VAC 3831112512153 61-100-202
Adapter for actuator to be ordered separately, when valve (DN 65-150) and actuator are
ordered separately.
TA-Slider 750 Plus / TA-Slider 1250 Plus
The Plus version has the following additional functions;
- Binay input, relays, output signal in mA
- BUS communication for ModBus, BACnet or KNX (with or without binay input, relays,
output signal in mA)
The Plus version of the TA-Slider actuators to be ordered separately. See separate technical leaflets
TA-Slider 750 and TA-Slider 1250.
Adapters for actuators
Valve DN EAN Article No
For recommended actuators
TA-Slider 750 32-50 *)
TA-Slider 750/1250 65-150 3831112529748 22413-001055
TA-MC100FSE/FSR 32-50 *)
TA-MC100FSE/FSR 65-150 3831112529748 22413-001055
For other actuators
JC VA1125-GGA-1 32-50 3831112531635 22412-000001
JC VA1125-GGA-1 65-150 3831112531628 22413-000001
JC VA7810-GGA-12 32-50 3831112531642 22412-000002
JC VA7810-GGA-12 65-150 3831112531659 22413-000002
Sauter AVM322 32-50 3831112532342 22412-000004
Sauter AVM322 65-150 3831112532359 22413-000004
Sauter AVM234, AVN, AVF 32-50 3831112531680 22412-000003
Sauter AVM234, AVN, AVF 65-150 3831112512214 22413-000003
Siemens SAX, SQV91 32-50 3831112531611 22214-000002
Siemens SAX, SQV91 65-150 3831112530928 22214-000001
*) Integrated in the valve.

17
Accessories
Measuring point
d L EAN Article No
DN 32-50
M14x1 44 7318792813207 52 179-014
M14x1 103 7318793858108 52 179-015
DN 65-150
3/8 47 7318792813009 52 179-008
3/8 103 7318792814501 52 179-608
Extension for measuring point M14x1
Suitable when insulation is used.
For DN 32-50.
d L EAN Article No
M14x1 71 7318793969507 52 179-016
Measuring point
Extensions 60 mm.
Can be installed without draining of the
system.
For all dimensions.
L EAN Article No
60 7318792812804 52 179-006
Tamper proof ring
For locking of set Kvmax.
For DN EAN Article No
32-50 7318794001800 22107-000001
Identification tag
EAN Article No
7318794001701 22107-000002
Insulation
See related insulation instruction under “Products & Solutions” on www.imi-hydronic.com or contact
IMI Hydronic Engineering.
L
d
d
dL

IMI TA / Control valves / TA-FUS1ON-C
18
Connections for DN 32-50
Welding connection
Swivelling nut
Max 120°C
Valve
DN
D Pipe
DN
EAN Article No
32 G1 1/2 32 7318792748806 52 009-032
40 G2 40 7318792748905 52 009-040
50 G2 1/2 50 7318792749001 52 009-050
Soldering connection
Swivelling nut
Max 120°C
Valve
DN
D Pipe
Ø
EAN Article No
32 G1 1/2 35 7318792749803 52 009-535
40 G2 42 7318792749902 52 009-542
50 G2 1/2 54 7318792750007 52 009-554
Connection with smooth end
For connection with press coupling
Swivelling nut
Max 120°C
Valve
DN
D Pipe
Ø
EAN Article No
32 G1 1/2 35 7318793811004 52 009-335
40 G2 42 7318793811103 52 009-342
50 G2 1/2 54 7318793811202 52 009-354

19

IMI TA / Control valves / TA-FUS1ON-C
The products, texts, photographs, graphics and diagrams in this document may be subject to
alteration by IMI Hydronic Engineering without prior notice or reasons being given. For the most up
to date information about our products and specifications, please visit www.imi-hydronic.com.
5-22-5 TA-FUSION-C v.5 06.2016