ANTUMBRA KLIK Instruction Manual

ANTUMBRA
KLIK
BUILDING INSTRUCTIONS
PCB V1.7

01. BUILD NOTES
Before you start building look through the build manual
so that you’ll be familiar with the building process and
you won’t run into any surprises! :)
Good luck!

TLC5940
ATMEGA328P-AU
7805
02. BACK
00. Orient the PCB as seen on the left.
01. Solder the TLC5940, watch out for it’s orientation!
02. Solder the Atmega 328P-AU, the dot should match up
with the dot on the silkscreen.
03. Solder the L7805.
04. Solder the two MMBT3904s.
00 01 02 0403
TLC5940 TLC5940
ATMEGA328P-AU
TLC5940
ATMEGA328P-AU
7805

TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
TLC5940
ATMEGA328P-AU
7805
16.000
TLC5940
ATMEGA328P-AU
7805
16.000
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102
02. BACK
05. Solder the crystal.
06. Solder the 1N5819 diode.
Watch out for it’s orientation!
07. Solder the two 470R resistors.
08. Solder the single 1K resistor.
09. Solder the single 2.2K resistor.
05 06 07 0908

TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
02. BACK
10. Solder the two 10k resistors.
11. Solder the two 100k resistors.
12. Solder the four 100nF capacitors.
13. Solder the two 22pF capacitors.
14. Solder the two 10uF electrolytic capacitors, their
orientation matter! Match the notched side with the
PCB drawing.
10 11 12 12 13

TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
TLC5940
ATMEGA328P-AU
7805
16.000
470
470
102 222
103
103
103
103
104 104
02. BACK
15. Solder the SMD LEDs for the jacklights. Check for ori-
entation! This is not necessary if you’re not fond of
blinkenlights. (shame on you)
16. Solder the 2x5 pin male header.
17. Solder the 2x3 pin male header.
18. Solder the 1x3 pin male header for the jack lights.
Again this is optional if you don’t ever want jack
lights, just leave them off.
15 16 17 18

03. FRONT
00. Orient the PCB as it is seen on the left.
01. DO NOT SOLDER YET!
Add the:
• jacks
• encoder
• 16 LEDs (longer leg goes in the hole with + )
• spacer
02. Put the panel on top, screw it to the spacer and add
the nuts to the jacks, align the encoder and LED nicely,
as you like it. Then solder everything in place.
00 01

04. FINISHED
You are now finished with building the module, congratu-
lations for your new awesome KLIK!

KLIK is designed by David Szebenyi under Antumbra.
www.antumbra.eu
Manual by David Szebenyi (www.aman.hu)
2018 • All rights reserved!