Impax IM2500I User manual

EC DECLARATION OF CONFORMITY
4HE MANUFACTURER OF THE PRODUCT COVERED BY THIS $ECLARATION IS
.!0 "RANDS ,TD
.APIER (OUSE 5NIT  #ORUNNA #OURT
7ARWICK 5NITED +INGDOM #6 (1
4HE MANUFACTURER HEREBY DECLARES THAT THE MACHINE AS DETAILED IN THIS DECLARATION FULFILS ALL THE
RELEVANT PROVISIONS OF THE -ACHINERY $IRECTIVE AND OTHER APPROPRIATE DIRECTIVES AS DETAILED BELOW
4HE MANUFACTURE FURTHER DECLARES THAT THE MACHINE AS DETAILED IN THIS DECLARATION WHERE APPLICABLE
FULFILS THE RELEVANT PROVISIONS OF THE ESSENTIAL HEALTH AND SAFETY REQUIREMENTS
4HE $IRECTIVES COVERED BY THIS $ECLARATION ARE AS DETAILED BELOW
0RODUCT $ETAILS
$ESCRIPTION )NVERTER 'ENERATOR
-ODEL .O )-)
"RAND .AME )MPAX
.AME AND ADDRESS OF TECHNICAL DOCUMENTATION HOLDER
4HE TECHNICAL DOCUMENTATION REQUIRED TO DEMONSTRATE THAT THE PRODUCT MEETS THE REQUIREMENTS OF
DIRECTIVE HAS BEEN COMPILED AND IS AVAILABLE FOR INSPECTION BY THE RELEVANT ENFORCEMENT AUTHORITIES
3IGNED 0RINT -ARK 3HANNON
1UALITY $IRECTOR
.!0 "RANDS ,TD
.APIER (OUSE 5NIT  #ORUNNA #OURT 7ARWICK 5NITED +INGDOM #6 (1
$ATE
%#4HE-ACHINERY$IRECTIVE
%# ,OW 6OLTAGE %QUIPMENT $IRECTIVE
%# %LECTROMAGNETIC #OMPATIBILITY $IRECTIVE
%# 4HE #% -ARKING $IRECTIVE
%# AS AMENDED BY %# 4HE 7ASTE %LECTRICAL AND %LECTRONIC %QUIPMENT 7%%%
$IRECTIVE
%# 4HE %MISSION OF 'ASEOUS AND 0ARTICULATE 0OLLUTANTS FROM )NTERNAL #OMBUSTION
%NGINES TO BE )NSTALLED IN .ON2OAD -OBILE -ACHINERY $IRECTIVE
%#!NNEX6)ANDTHE$IRECTIVE%# 4HE .OISE %MISSIONS IN THE %NVIRONMENT
BY %QUIPMENT FOR USE /UTDOORS 2EGULATIONS  3)  AS AMENDED
!FTER SALES SUPPORT 4EL    7EBSITE WWWIMPAXPOWERTOOLSCOM
14
!ND IS IN CONFORMITY WITH THE APPLICABLE REQUIREMENTS OF THE FOLLOWING DOCUMENTS
%.
%.
%.
%.)3/

!LWAYS 2EAD )NSTRUCTION -ANUAL
2ETAIN FOR &UTURE 2EFERENCE
IM2500I
2500W INVERTER GENERATOR

2
CERTIFICATE OF GUARANTEE
This product is guaranteed for a period of 1 Year, with effect from the date of purchase and applies
only to the original purchaser. This guarantee only applies to defects arising from, defective materials
and or faulty workmanship that become evident during the guarantee period only and does not
include consumable items. The manufacturer will repair or replace the product at their discretion
subject to the following. That the product has been used in accordance with the guidelines as
detailed in the product manual and that it has not been subjected to misuse, abuse or used for a
purpose for which it was not intended. That it has not been taken apart or tampered with in any way
whatsoever or has been serviced by unauthorised persons or has been used for hire purposes.
Transit damage is excluded from this guarantee, for such damage the transport company is
responsible. Claims made under this guarantee must be made in the first instance, directly to the
retailer within the guarantee period. Only under exceptional circumstances should the product be
returned to the manufacturer. In this case it shall be the consumer’s responsibility to return the
product at their cost ensuring that the product is adequately packed to prevent transit damage and
must be accompanied with a brief description of the fault and a copy of the receipt or other proof of
purchase. The manufacturer shall not be liable for any special, exemplary, direct, indirect, incidental,
or consequential loss or damage under this guarantee. This guarantee is in addition to and does not
affect any rights, which the consumer may have by virtue of the Sale of Goods Act 1973 as
amended 1975 and 1999.
INTRODUCTION
Thankyou for purchasing this product which has passed through our extensive quality assurance
process. Every care has been taken to ensure that it reaches you in perfect condition. However, in
the unlikely event that you should experience a problem, or if we can offer any assistance or advice
please do not hesitate to contact our customer care department. For details of your nearest
customer care department please refer to the telephone numbers at the back of this manual.
Safety First
Before attempting to operate this product the following basic safety precautions should always be
taken to reduce the risk of fire, electric shock and personal injury. It is important to read the
instruction manual to understand the application, limitations and potential hazards associated with
this product.
HELPLINE & SPARE PARTS
In the unlikely event of a defect occurring please contact our Helpline.
Office hours: Monday - Friday 9:00am – 5:30pm.
Telephone Number 0844 264 2485

3
SAFETY INFORMATION
Specific Safety Instructions
Electrical generator must always be grounded,
(connected to earth).
Petrol or diesel powered generators must never
be used in an unventilated closed spaces. The
exhaust fumes are highly dangerous and can
cause “Carbon Monoxide Poisoning” which will
cause drowsiness and death.
The generator must be mounted on a firm level
surface.
The electrical output load must not exceed the
maximum load stated on the rating plate.
Exceeding the rated load will damage the unit
or shorten its life and will invalidate the
guarantee.
The engine must not be run at speeds that
exceed the maximum stated on the rating plate.
Operating an engine at excessive speeds
increases the hazard of personal injury.
Do not tamper with components, which may
increase or decrease the governed speed.
Mains extension leads, mains supply leads, and
all electrical equipment must be in good working
condition.
Never operate electrical equipment with
damaged or defective mains supply leads.
Keep the area around the generator clear of
obstructions at all times. Never locate the
generator against a building or near a canvas or
plastic structure i.e. Tents etc.
Always use the correct fuel mix as stated in the
user manual and on the rating plate.
To prevent fire, always stop the engine when
refueling and never over fill the fuel tank.
Always clean up spilt fuel immediately using
sand.
Do not use the generator in or near an explosive
atmosphere.
To prevent an electric shock, never operate the
machine in rain, snow or touch with wet hands.
Check the fuel system periodically for leaks,
seals and hoses should be checked for signs of
deterioration or chafing. Check for loose or
missing clamps, damaged fuel tank or filler cap.
All defects should be corrected before further
use.
Always allow the generator to reach full
operating speed before connecting any
electrical load.
Always disconnect the electrical load before
switching the generator off.
To prevent surging that may possibly damage
electrical equipment, do not allow engine to run
out of fuel while electrical loads are connected.
Before transporting the generator in a vehicle,
drain all fuel to prevent leakage.
To prevent an electric shock and fire, never
connect an electrical load with the electrical
output switched on.
Do not connect the generator to any other
electrical source.
The engine speed has been factory set to
provide safe operation. Tampering with the
engine speed adjustment could result in
overheating of attachments and could cause a
fire. Never attempt to “speed-up” the engine to
obtain more performance. Both the output
voltage and frequency will be thrown out of
standard by this practice, endangering
attachments and the user.
Store the generator in a well-ventilated area with
the fuel tank empty.
Fuel Filling instructions
Warning! Select bare ground for fuelling and
move at least 10 feet (3m) from fuelling spot
before starting the engine. After refuelling,
properly tighten fuel cap; wipe off any spilled
fuel and check for leakage.
Warning! If fuel gets spilled on clothes,
especially trousers, it is very important to
change clothes immediately. Do not rely on
evaporation.
Flammable quantities of fuel may remain on
clothes after a spill for longer than expected.

SAFETY INFORMATION
Warning! Vibrations can cause an improperly
tightened fuel cap to loosen or come off and
spill quantities of fuel. In order to reduce the risk
of fuel spillage and fire, tighten fuel filler cap by
hand as securely as possible.
Before use always make sure that the fuel cap
has been properly tightened. Check for fuel
leakage while refuelling and during operation. If
a fuel leak is suspected, do not start or run the
engine until leak is fixed and spilled fuel has
been wiped away.
Warning! The ignition system of your unit
produces an electromagnetic field of a very low
intensity. This field may interfere with some
pacemakers. To reduce the risk of serious or
fatal injury, people with a pacemaker fitted
should consult their physician and the
pacemaker manufacturer before operating this
tool.
General Safety Rules
Warning! Read all instructions Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury. The term
"power tool" in all of the warnings listed below
refers to your mains operated (corded) power
tool or battery operated (cordless) power tool.
Save These Instructions
1) Work Area
a) Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical Safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
3) Personal Safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication.
A moment of inattention while operating
power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye
protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the
switch is in the off position before
plugging in. Carrying power tools with your
finger on the switch or plugging in power
tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
4

5
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of these devices can reduce dust
related hazards.
4) Power Tool Use And Care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc., in accordance with these
instructions and in the manner intended
for the particular type of power tool,
taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
SAFETY INFORMATION

COMPONENTS
6












#OMPONENT ,IST
 %NGINE /./&& SWITCH
 %CONOMY CONTROL SWITCH
 &UEL /./&& TAP
 !IR FILTER AND OIL FILLER MAINTENANCE COVER
 #HOKE LEVER
 !# SOCKET
 'ROUND EARTH TERMINAL
 2ECOIL STARTER
 $# SOCKET
 $# CIRCUIT BREAKER
 0ILOT LIGHT /UTPUT
 /VERLOAD INDICATOR LIGHT
 ,OW /IL WARNING LIGHT
 &UEL FILLER CAP
 &UEL TANK VENT TAP
 3PARK PLUG MAINTENANCE COVER
 %XHAUST
 $# CHARGING LEADS
 3CREWDRIVER
 3PARK PLUG SPANNER
4ECHNICAL SPECIFICATION
!# OUTPUT 6^(Z
2ATED POWER K6!
0
2ATEDCURRENT !
EAK POWER K6!
0HASE 3INGLE
0OWER FACTOR COSĆ
$ISPLACEMENT CC
$# OUTPUT 6!
%NGINE (0  STROKE
.O LOAD SPEED LOW MIN
.O LOAD SPEED HIGH MIN
#ONTINUOUS OPERATING TIME HRS  LOAD
&UEL TANK CAPACITY ,
&UEL TYPE 5NLEADED PETROL
/IL TYPE 3!% 7
/IL CAPACITY ,
)GNITION SYSTEM 4#)
3TARTING SYSTEM 2ECOIL STARTER
3PARK PLUG TYPE !24#
3OUND POWER LEVEL D"!
 



  


7
UNPACKING AND OPERATING INSTRUCTIONS
5NPACKING
#AUTION 4HIS PACKAGING CONTAINS SHARP OBJECTS
4AKE CARE WHEN UNPACKING 2EMOVE THE
MACHINE TOGETHER WITH THE ACCESSORIES
SUPPLIED FROM THE PACKAGING #HECK CAREFULLY TO
ENSURE THAT THE MACHINE IS IN GOOD CONDITION
AND ACCOUNT FOR ALL THE ACCESSORIES LISTED IN THIS
MANUAL !LSO MAKE SURE THAT ALL THE ACCESSORIES
ARE COMPLETE )F ANY PARTS ARE FOUND TO BE
MISSING THE MACHINE AND ITS ACCESSORIES SHOULD
BE RETURNED TOGETHER IN THEIR ORIGINAL PACKAGING
TO THE RETAILER
$O NOT THROW THE PACKAGING AWAY KEEP IT SAFE
THROUGHOUT THE GUARANTEE PERIOD THEN RECYCLE IF
POSSIBLE OTHERWISE DISPOSE OF IT BY THE PROPER
MEANS $O NOT LET CHILDREN PLAY WITH EMPTY
PLASTIC BAGS DUE TO THE RISK OF SUFFOCATION
/PERATING )NSTRUCTIONS
,OCATION AND 'ROUNDING
"EFORE USING THIS GENERATOR IT MUST BE PREPARED
CORRECTLY BEFORE USE ,OCATE THE GENERATOR ON
FIRM LEVEL GROUND AWAY FROM BUILDINGS OR OTHER
STRUCTURES ENSURING THAT THE EXHAUST IS NOT
OBSTRUCTED
7ARNING )T IS ADVISABLE TO PROPERLY EARTH
GROUND YOUR GENERATOR BEFORE STARTING USING A
WIRE AND A SMALL EARTH STAKE .OTE 4HE WIRE AND
EARTH STAKE ARE NOT SUPPLIED WITH THE UNIT
%ARTH SPIKE AND CABLE CAN BE PURCHASED AT YOUR
LOCAL CAMPING SUPPLIES OR ALTERNATIVELY AN EARTH
SPIKE CAN BE MADE AND IT IS SUGGESTED YOU GET
ADVICE FROM A REGISTERED ELECTRICAL TRADES
PERSON 4O MAKE A SPIKE USE A COPPER TUBE OR
COPPER ROD MM DIAMETER A MINIMUM LENGTH
OF MM AND WITH AN - MACHINE SCREW ONE
END 4HE CABLE USED SHOULD BE A MAXIMUM
LENGTH OF  METRE AND A MINIMUM OF MMTO
CARRY A AMP LOAD 4HE CABLE SHOULD BE
ATTACHED TO THE GENERATOR AT THE EARTH POINT
&IG  AND TO THE SPIKE BETWEEN A FLAT WASHER
AND THE COPPER WITH A LOCK WASHER UNDER THE
HEAD OF THE - -ACHINE SCREW IN A SIMILAR
FASHION TO THE EARTH POINT SCREW ON THE
GENERATOR
7HEN PLACING THE SPIKE INTO THE GROUND THE
GENERATOR MUST NOT BE RUNNING AND IT IS
SUGGESTED THAT THE SPIKE IS PUSHED INTO THE
GROUND BY AT LEAST MM SO THAT IT IS FIRM AND
A LITRE OF WATER POURED AROUND IT TO ENSURE GOOD
EARTH CONTINUITY
#HECKING 4HE /IL
7ARNING 4HE GENERATOR IS SUPPLIED WITHOUT OIL
AND MUST BE FILLED BEFORE FIRST USE FAILURE TO DO
SO WILL INVALIDATE YOUR GUARANTEE ,OOSEN THE
COVER SCREW AND REMOVE THE MAINTENANCE COVER
&IG 
2EMOVE THE OIL FILLER CAP AND WIPE THE DIPSTICK
CLEAN &IG 
&IG 
&IG 
&IG 
-AX OIL LEVEL

OPERATING INSTRUCTIONS
8
Check the oil level by inserting the dipstick into
the filler neck without screwing it in. If the level
is low, fill to the top of the oil filler neck with the
recommended oil.
Use high-detergent, premium quality 4-stroke
engine oil SAE 10W-30.
Warning! Non-detergent and 2-stroke engine
oils will damage the engine and are not
recommended.
Low Oil Alert System
The low oil alert system is designed to prevent
engine damage caused by an insufficient
amount of oil in the crankcase. Before the oil
level in the crankcase can fall below a safe limit,
the low oil alert indicator light turns on and the
low oil alert system will automatically shut down
the engine.
Note: The engine switch will remain in the On
position. If the engine stops or the oil alert
indicator light turns on when you pull the starter
grip, check the engine oil level. Oil must be
added to the engine before it will re-start.
Fueling
Danger!
STOP engine before adding fuel. This engine is
certified to operate on unleaded gasoline.
Unleaded gasoline produces fewer engine and
spark plug deposits and extends exhaust
system life.
Warning! Never use stale or contaminated
gasoline or an oil/gasoline mixture. Avoid getting
dirt or water in the fuel tank.
Replace and secure the fuel cap after adding
fuel, Fig 4.
Petrol is extremely flammable and explosive
under certain conditions.
Do not smoke or allow flames or sparks where
the generator is refuelled or where Petrol is
stored.
Refuel in a well-ventilated area.
Do not let fuel spill over the generator casing. If
there is some fuel spillage, be sure that it has
evaporated before starting the engine.
Avoid touching gasoline or breathing in gasoline
fumes.
Starting the generator
AC Power Applications. Before using this
generator it must be prepared correctly before
use. Locate the generator on firm level ground
away from buildings or other structures ensuring
that the exhaust is not obstructed.
Before starting the engine make sure that all the
electrical loads are disconnected from the
generator AC outlet socket.
Open the fuel filler cap vent (Fig 5) and the fuel
cock, Fig 6.
Fig 4
Fig 5
Fig 6

9
OPERATING INSTRUCTIONS
4URN THE ENGINE SWITCH TO THE /N POSITION AND
THE ECONOMY SWITCH TO THE /FF POSITION &IG 
4O START A COLD ENGINE SET THE CHOKE TO THE
m#(/+%n POSITION &IG 
#AUTION 7HEN ENGINE IS HOT OR ENVIRONMENT
TEMPERATURE IS HIGH SET THE CHOKE TO THE m2UNn
POSITION
(OLD DOWN THE GENERATOR FIRMLY WITH ONE HAND
7ITH THE OTHER HAND GRIP THE RECOIL STARTER CORD
HANDLE AND PULL SLOWLY UNTIL RESISTANCE IS FELT
INDICATING THAT THE RECOIL STARTER IS ENGAGED
7HEN RESISTANCE IS FELT PULL THE CORD SHARPLY
#ONTINUE THIS PROCEDURE UNTIL THE ENGINE STARTS
&IG 
#AUTION $O NOT ALLOW THE STARTER GRIP TO SNAP
BACK
7HEN THE ENGINE HAS BEEN SUCCESSFULLY STARTED
AND IS RUNNING SMOOTHLY RETURN THE CHOKE TO THE
m25.n POSITION
7ARNING "EFORE CONNECTING ANY ELECTRICAL LOAD
TO THE GENERATOR ENSURE THAT THE LOAD DOES NOT
EXCEED THE MAXIMUM LOAD AS STATED ON THE
RATING PLATE %NSURE THAT THE APPLIANCE BEING
CONNECTED IS IN GOOD WORKING ORDER AND THAT THE
MAINS SUPPLY LEAD IS LONG ENOUGH TO REACH THE
GENERATOR WITHOUT ANY STRAIN
7HEN THE GENERATOR ENGINE HAS BEEN
SUCCESSFULLY STARTED AND IS RUNNING SMOOTHLY
CONNECT THE ELECTRICAL LOAD INTO THE GENERATOR !#
OUTPUT SOCKET
7ARNING $# POWER AND !# POWER CAN BE USED
AT THE SAME TIME BUT $/ ./4 EXCEED THE
MAXIMUM POWER OUTPUT AS SHOWN ON THE RATING
PLATE
$# "ATTERY #HARGING &UNCTION
4HIS FUNCTION IS APPLICABLE TO 6 BATTERY
CHARGING ONLY
$ISCONNECT THE LEADS FROM THE BATTERY
,OOSEN THE VENTS ON THE BATTERY
-AKE SURE THE BATTERY FLUID LEVEL IS CORRECT
5SING A HYDROMETER MEASURE THE SPECIFIC GRAVITY
OF THE BATTERY FLUID AND CALCULATE THE CHARGING
TIME IN ACCORDANCE WITH THE TABLE SHOWN &IG 
!TTACH THE V CHARGING LEADS TO THE BATTERY
OBSERVING CORRECT POLARITY 2ED   0OSITIVE
BLACK   .EGATIVE
0LUG THE V CHARGER LEAD INTO THE SOCKET ON THE
GENERATOR &IG 
4HE SPECIFIC GRAVITY FOR THE FULLY CHARGED BATTERY
SHALL BE WITHIN  TO  )T IS ADVISABLE TO
CHECK THE SPECIFIC GRAVITY EVERY HOUR
&IG 
&IG 
&IG 
/.
/&&
25. #(/+%

OPERATING INSTRUCTIONS
10
%CONOMY #ONTROL 3WITCH &IG 
/N 2ECOMMENDED TO MINIMIZE FUEL
CONSUMPTION AND FURTHER REDUCE NOISE LEVELS
WHEN NO LOAD IS APPLIED TO THE GENERATOR
/FF 4HE SMART THROTTLE SYSTEM DOES NOT OPERATE
%NGINE SPEED VARIES WITH THE LOAD
7ITH THE SWITCH IN THE /N POSITION THE ENGINE
SPEED IS CONTROLLED AUTOMATICALLY 4HE ENGINE
SPEED IS LOWERED WHEN THE LOAD ON THE
GENERATOR IS REDUCED TURNED OFF OR
DISCONNECTED 7HEN LOADS ARE TURNED ON OR
RECONNECTED THE ENGINE RETURNS TO THE CORRECT
SPEED TO POWER THE CONNECTED LOAD
)N THE /FF POSITION THE SYSTEM DOES NOT OPERATE
4HE ECONOMY SYSTEM ALSO HELPS IN FUEL ECONOMY
AND REDUCED NOISE LEVELS WHEN UNDER NO LOAD
CONDITIONS
7HEN A LOAD IS CONNECTED TO THE GENERATOR THE
GENERATOR SPEED WILL AUTOMATICALLY ADJUST IN
ORDER TO SUPPLY ENOUGH POWER
!PPLIANCES WITH LARGE STARTUP POWER DEMANDS
MAY NOT ALLOW THE ENGINE TO REACH NORMAL
OPERATING SPEED WHEN THEY ARE CONNECTED TO THE
GENERATOR 4URN THE ECONOMY SWITCH TO THE /FF
POSITION AND CONNECT THE APPLIANCE TO THE
GENERATOR )F THE ENGINE STILL WILL NOT REACH NORMAL
OPERATING SPEED CHECK THAT THE APPLIANCE DOES
NOT EXCEED THE RATED LOAD CAPACITY OF THE
GENERATOR
3TOPPING 4HE 'ENERATOR %NGINE
"EFORE STOPPING THE ENGINE MAKE SURE THAT ALL
THE ELECTRICAL LOADS ARE DISCONNECTED FROM THE
GENERATOR !# OUTLET SOCKET 4URN THE GENERATOR
/N/FF SWITCH TO THE /FF POSITION &IG 
#LOSE THE FUEL FILLER CAP VENT &IG 
&IG 
&IG 
&IG 

11
OPERATING INSTRUCTIONS
/VERLOAD 0ROTECTION &IG 
5NDER NORMAL WORKING CONDITIONS THE 'REEN
OUTPUT INDICATOR LIGHT WILL BE ILLUMINATED
)F THE GENERATOR IS OVERLOADED OR IF THERE IS A
MALFUNCTION OR A SHORT CIRCUIT IN A CONNECTED
APPLIANCE THE 'REEN OUTPUT INDICATOR WILL
EXTINGUISH AND THE 2ED OVERLOAD INDICATOR LIGHT
ILLUMINATES AND THE POWER TO THE CONNECTED
APPLIANCE WILL BE DISCONNECTED
)F THE 2ED OVERLOAD INDICATOR LIGHT ILLUMINATES
STOP THE GENERATOR AND INVESTIGATE THE CAUSE
"EFORE CONNECTING AN APPLIANCE TO THE
GENERATOR CHECK THAT IT IS IN GOOD ORDER AND THAT
ITS ELECTRICAL RATING DOES NOT EXCEED THAT OF THE
GENERATOR 4HEN CONNECT THE POWER CORD OF THE
APPLIANCE AND START THE ENGINE
7HEN AN ELECTRIC MOTOR IS STARTED BOTH THE
2ED OVERLOAD INDICATOR AND THE 'REEN OUTPUT
INDICATOR WILL ILLUMINATE SIMULTANEOUSLY 4HIS IS
NORMAL THE 2ED OVER LOAD INDICATOR
EXTINGUISHES AFTER ABOUT FOUR  SECONDS )F THE
2ED OVERLOAD INDICATOR REMAINS ILLUMINATED
CONSULT YOUR GENERATOR DEALER
#AUTION 3UBSTANTIAL OVERLOADING THAT
CONTINUOUSLY ILLUMINATES THE 2ED OVERLOAD
INDICATOR MAY DAMAGE THE GENERATOR )F THE 2ED
OVERLOAD INDICATOR LIGHT AND THE 'REEN OUTPUT
INDICATOR ILLUMINATE AT THE SAME TIME WHEN
ENGINE STARTS AND THE 2ED OVERLOAD INDICATOR
REMAINS ILLUMINATED AFTER THE 'REEN OUTPUT
INDICATOR EXTINGUISHES PLEASE CONTACT YOUR
SUPPLIER
.OTE &OR EQUIPMENT WITH AN INDUCTIVE LOAD
MORE POWER WILL BE REQUIRED AT INITIAL START
5NDER THESE CONDITIONS IT IS NORMAL FOR BOTH THE
2ED OVERLOAD INDICATOR AND THE 'REEN OUTPUT
INDICATOR WILL ILLUMINATE SIMULTANEOUSLY FOR A
SHORT PERIOD ABOUT FOUR  SECONDS !FTER THE
APPLIANCE STARTS THE 2ED OVERLOAD INDICATOR
EXTINGUISHES AND THE 'REEN OUTPUT INDICATOR
WILL REMAIN ILLUMINATED
4HE CIRCUIT BREAKER FOR THE 6 $# CHARGING
FUNCTION IS POSITIONED NEXT TO THE 6 SOCKET
&IG 
&IG 
&IG 
&IG 
&IG 
34/0

OPERATING INSTRUCTIONS
12
Spark Plug Maintenance
To ensure proper engine operation, the spark
plug must be properly gapped and free of
deposits.
Remove the spark plug maintenance cover,
Fig 17.
Pull the HT lead off the spark plug, Fig 18, and
clean any dirt from around the spark plug base.
Using the wrench supplied remove the spark
plug, Fig 19.
Visually inspect the spark plug. Discard it if the
insulator is cracked or chipped. Please use a
spark plug gauge to check the spark plug gap, it
should be 0.6-0.7mm (0.024-0.028inch).
Check that the spark plug sealing washer is in
good condition, and thread the spark plug in by
hand to prevent cross threading.
After the spark plug is seated, tighten with a
spark plug wrench to compress the washer. If
installing a new spark plug, tighten 1/2 turn after
the spark plug seats to compress the washer. If
reinstalling a used spark plug, tighten 1/8 - 1/4
turn after the spark plug seats to compress the
washer.
Reinstall the spark plug cap on the spark plug
securely.
Reinstall the spark plug maintenance cover.
Warning! Spark plug must be assembled firmly,
or it will become hot and may damage
generator.
A loose spark plug can overheat and damage
the engine.
Engine Oil Replacement
Remove the side maintenance cover, Fig 20.
Note: Drain the used oil while the engine is
warm. Warm oil drains quickly and completely.
Place a suitable container under the engine to
catch the used oil. Remove the dipstick and
pour out the old oil into the container, Fig 21.
Fig 17
Fig 18
Fig 19
Fig 20

13
OPERATING INSTRUCTIONS
7ITH THE ENGINE IN A HORIZONTAL POSITION FILL TO
THE TOP OF THE OIL FILLER NECK WITH THE
RECOMMENDED OIL
2EPLACE THE DIPSTICK THEN REINSTALL THE
MAINTENANCE COVER AND TIGHTEN THE COVER SCREW
SECURELY
.OTE )MPROPER DISPOSAL OF ENGINE OIL CAN BE
HARMFUL TO THE ENVIRONMENT )F YOU CHANGE OIL
PLEASE DISPOSE OF IT PROPERLY 0UT IT IN A SEALED
CONTAINER AND TAKE IT TO A RECYCLING CENTRE $O
NOT DISCARD IT IN HOUSEHOLD WASTE DUMP IT ON
THE GROUND OR POUR IT DOWN A DRAIN
&UEL 4ANK &ILTER &IG 
!FTER EVERY  HOURS OF RUNNING OR EVERY 
MONTHS THE FUEL TANK FILTER SHOULD BE REMOVED
AND CLEANED
2EMOVE THE FUEL TANK FILLER CAP AND THE FILTER
CLEAN THE FILTER THOROUGHLY USING AN
ENVIRONMENTALLY FRIENDLY WATER BASED DEGREASING
AGENT AND REFIT
!IR &ILTER
! DIRTY AIR CLEANER WILL RESTRICT AIR FLOW TO THE
CARBURETTOR 4O PREVENT CARBURETTOR MALFUNCTION
SERVICE THE AIR CLEANER REGULARLY
7ARNING 5SING GASOLINE OR FLAMMABLE SOLVENT
TO CLEAN THE AIR FILTER CAN CAUSE A FIRE OR
EXPLOSION 5SE ONLY SOAPY WATER OR A NON
FLAMMABLE SOLVENT
(AVING FIRST REMOVED THE SIDE MAINTENANCE
COVER &IG LOOSETHENUTSWITH-SOCKET
WRENCHANDSCREWSONTHEAIRCLEANERCOVER
ANDREMOVETHECOVER&IG4HENRELEASE
BOLTWITH-SOCKETWRENCH
0ULLAWAYTHEAIRCLEANERHOUSINGUSETHEFLAT
SCREWDRIVERTORELEASETWOPLASTICCLIPSTHENTHE
FILTERCANNOWBEREMOVED&IG
7ASH THE AIR FILTER IN A SOLUTION OF HOUSEHOLD
DETERGENT AND WARM WATER THEN RINSE IT THOROUGHLY
OR WASH IT IN A NON FLAMMABLE OR HIGH FLASH POINT
SOLVENT !LLOW THE AIR FILTER TO DRY THOROUGHLY
&IG 
&IG 
&IG 
&IG 

OPERATING INSTRUCTIONS
14
'ENERAL )NSPECTION !ND 3TORAGE
2EGULARLY CHECK THAT ALL THE FIXING SCREWS ARE
TIGHT 4HEY MAY VIBRATE LOOSE OVER TIME
3TORAGE
)F THE GENERATOR IS NOT TO BE USED OR IS TO BE
STORED FOR MORE THAN ONE MONTH THE FOLLOWING
STORAGE PROCEDURE SHOULD BE CARRIED OUT $RAIN
ALL THE FUEL FROM THE FUEL TANK AND THE
CARBURETTOR ENSURE THAT ALL THE FUEL HAS BEEN
REMOVED 2EMOVE THE SPARK PLUG AND POUR
APPROXIMATELY ONE TABLESPOON FULL OF CLEAN
ENGINE OIL INTO THE SPARK PLUG HOLE 7ITH THE
IGNITION TURNED /&& GENTLY PULL ON THE RECOIL
STARTER CORD SEVERAL TIMES 2EFIT THE SPARK PLUG
/IL &ILTER
4HE OIL FILTER SHOULD BE CLEANED EVERY  MONTHS
OR  HOURS OR USE 4HE OIL FILTER CAN BE FOUND
ON THE BASE OF THE GENERATOR %NSURE THE
GENERATOR HAS BEEN DRAINED OF OIL REMOVE THE
CAP &IG  TO GAIN ACCESS TO THE FILTER ASSEMBLY
&IG 
&IG 
&IG 
&IG 
&IG 
2EINSTALL THE AIR FILTER AND CLEANER COVER THEN
REINSTALL THE MAINTENANCE COVER

OPERATING INSTRUCTIONS
15
AND CONTINUE TO PULL THE RECOIL STARTER CORD UNTIL
THE PISTON IS ON THE COMPRESSION STROKE WHEN
RESISTANCE IS FELT THEN STOP PULLING
3TORE THE GENERATOR IN A DRY WELL VENTILATED PLACE
UNDER A COVER TO PREVENT ANY DUST OR DEBRIS FROM
ACCUMULATING ON THE GENERATOR
0,%!3% ./4%
)F USING FOR A CARAVAN MOTOR HOME
OR BOAT ETC REFER TO THE
MANUFACTURERS MANUAL REGARDING
CONNECTION OF A GENERATOR
$O ./4 CONNECT INTO A HOUSE
RING MAIN CIRCUIT

16
TROUBLESHOOTING

TROUBLESHOOTING
17

18
MAINTENANCE CHART
)TEM 2EMARK 0REOPERATION )NITIAL  MONTH %VERY  MONTH %VERY  MONTH %VERY  MONTH
CHECK DAILY OR HOURS OR  HOURS OR  HOURS OR  HOURS
3PARK PLUG #HECK CONDITION
!DJUST GAP AND CLEAN
2EPLACE IF REQUIRED
%NGINE OIL #HECK OIL LEVEL
2EPLACE
!IR FILTER #LEAN REPLACE IF REQUIRED
&UEL &ILTER #LEAN FUEL COCK FILTER
2EPLACE IF REQUIRED
6ALVE #HECK AND ADJUST WHEN
CLEARANCE ENGINE IS COLD
&UEL LINE #HECK FUEL HOSE FOR CRACKS
OR DAMAGE 2EPLACE IF REQUIRED
%XHAUST #HECK FOR LEAKAGE 4IGHTEN OR
SYSTEM REPLACE GASKET IF REQUIRED
#HECK EXHAUST SCREEN #LEAN
AND REPLACE IF REQUIRED
#ARBURETOR #HECK CHOKE OPERATION
#OOLING #HECK FAN DAMAGE
SYSTEM
3TARTING #HECK RECOIL STARTER
SYSTEM OPERATION
$ECARBON -ORE FREQUENTLY
ISATION IF NECESSARY
&ITTINGS #HECK ALL FITTINGS AND FIXTURES
&ASTENINGS AND TIGHTEN IF REQUIRED
4HE FIGURES QUOTED ARE EMISSION LEVELS AND ARE
NOT NECESSARILY SAFE WORKING LEVELS 7HILST THERE
IS A CORRELATION BETWEEN THE EMISSION AND
EXPOSURE LEVELS THIS CANNOT BE USED RELIABLY TO
DETERMINE WHETHER OR NOT THE ACTUAL LEVEL OF
EXPOSURE OF THE WORKROOM THE OTHER SOURCES OF
NOISE ETC IE THE NUMBER OF MACHINES AND THE
ADJACENT PROCESSES AND THE LENGTH OF TIME FOR
WHICH AN OPERATOR IS EXPOSED TO THE NOISE !LSO
THE PERMISSIBLE EXPOSURE LEVEL CAN VARY FROM
COUNTRY 4HIS INFORMATION HOWEVER WILL ENABLE THE
USER OF THE MACHINE TO MAKE A BETTER EVALUATION
OF THE HAZARD AND RISK 4HE SUPPLIER
RECOMMENDS THE USE OF EAR PROTECTION AT ALL
TIME

19
ENVIRONMENTAL PROTECTION
)NFORMATION FOR PRIVATE HOUSEHOLDERS FOR THE ENVIRONMENTALLY RESPONSIBLE DISPOSAL OF 7ASTE
%LECTRICAL AND %LECTRONIC %QUIPMENT 7%%%
4HIS SYMBOL ON PRODUCTS AND OR ACCOMPANYING DOCUMENTS INDICATES THAT USED
AND END OF LIFE ELECTRICAL AND ELECTRONIC EQUIPMENT SHOULD NOT BE DISPOSED OF IN
HOUSEHOLD WASTE &OR THE PROPER DISPOSAL TREATMENT RECOVERY AND RECYCLING
PLEASE TAKE THESE PRODUCTS TO DESIGNATED COLLECTION POINTS WHERE THEY WILL BE
ACCEPTED ON A FREE OF CHARGE BASIS !LTERNATIVELY IN SOME COUNTRIES YOU MAY BE
ABLE TO RETURN YOUR PRODUCTS TO YOUR RETAILER UPON THE PURCHASE OF AN EQUIVALENT
NEW PRODUCT $ISPOSING OF THIS PRODUCT CORRECTLY WILL HELP TO SAVE VALUABLE
RESOURCES AND PREVENT ANY POTENTIAL ADVERSE EFFECTS ON HUMAN HEALTH AND THE
ENVIRONMENT WHICH COULD OTHERWISE ARISE FROM INAPPROPRIATE WASTE DISPOSAL AND HANDLING 0LEASE
CONTACT YOUR LOCAL AUTHORITY FOR FURTHER DETAILS OF YOUR NEAREST DESIGNATED COLLECTION POINT 0ENALTIES
MAY BE APPLICABLE FOR INCORRECT DISPOSAL OF THIS WASTE IN ACCORDANCE WITH NATIONAL LEGISLATION
&/2 "53).%33 53%23 ). 4(% %52/0%!. 5.)/.
)F YOU WISH TO DISCARD ELECTRICAL AND ELECTRONIC EQUIPMENT PLEASE CONTACT YOUR DEALER OR SUPPLIER FOR
FURTHER INFORMATION
)NFORMATION ON $ISPOSAL IN OTHER #OUNTRIES OUTSIDE THE %UROPEAN 5NION
4HIS 3YMBOL IS ONLY VALID IN THE %UROPEAN 5NION
)F YOU WISH TO DISPOSE OF THIS PRODUCT PLEASE CONTACT YOUR LOCAL AUTHORITIES OR DEALER AND ASK FOR THE
CORRECT METHOD OF DISPOSAL