impro XTT908-1-0-GB Series User manual

MODEL NUMBER: XTT908-1-0-GB-XX
IMPROX DPA
ImproX (DPA) 125 kHz Door Entry Panel Antenna Reader
INSTALLATION MANUAL
SPECIFICATIONS
Working Environment .................
Designed to work in an indoor or outdoor
environment similar to IP66. The ImproX DPA
is, therefore, sealed (potted) against water.
Buzzer
Volume and Tone...................
Single tone, 4-step adjustable volume.
Status Indicators
Status LED.............................
Bi-coloured Red or Green.
INSTALLATION INFORMATION
Accessories
Find the following when unpacking the Antenna Reader:
An ImproX DPA Antenna Reader housed in a Black, ABS Plastic housing. The
ImproX DPA includes 8 m (26 ft) of 4-core, 0.5 mm Solid Strand Communications
Cable.
A Piezo-electric, External Drive Buzzer.
An extra Serial Number Label.
General
Remember the following when installing the Antenna Reader:
Maximum Data Communications Distance
The ideal cable distance between the Terminal, Controller or Receiver and its Antenna
Reader ranges between 2 m to 16 m (7 ft to 53 ft). Achieve this by using a good quality
shielded multi-strand 3-pair twisted cable. The cross-sectional area of the cable must
not be less than 0.2 mm2(0.0003 in2).

XTT316-0-0-GB-08
December 2007
Page 2
Cable Specifications
The cable specifications should be similar to the following:
Conductor Resistance: < 2 ohms.
Capacitance, Core to Earth: < 160 pF/m.
Capacitance, Core to Core: < 100 pF/m.
Distance between Antenna Readers from the SAME Terminal, Controller
or Receiver
To avoid mutual interference, install the Antenna Readers no closer than 150 mm (6 in)
apart.
Distance between Antenna Readers from DIFFERENT Terminals,
Controllers or Receivers
To avoid mutual interference, install the Antenna Readers no closer than 500 mm
(20 in) apart.
Mounting in a User Supplied Enclosure
CAUTION: Make certain that you mount the Antenna Reader on a vibration-free
surface.
The ImproX DPA is designed for mounting in a user supplied enclosure. Select the
mounting position of the ImproX DPA, considering accessibility, routing of wires and
visibility of the externally visible Status LED.
The Antenna Reader has 4 mounting holes, drilled to 4 mm in diameter. The mounting
holes accommodate M3 bolts and nuts.
Drill a 5 mm diameter hole for the cable.
Blank Space

XTT316-0-0-GB-08
December 2007
Page 3
Connecting the ImproX DPA
Figure 1 to Figure 4 show detailed connection diagrams for the ImproX DPA.
Figure 1: ImproX DPA Connected to the SupaGate Receiver

XTT316-0-0-GB-08
December 2007
Page 4
Figure 2: ImproX DPA Connected to the IXP110 Controller

XTT316-0-0-GB-08
December 2007
Page 5
Figure 3: ImproX DPA Connected to the IXP121 Controller or the ImproX MfT

XTT316-0-0-GB-08
December 2007
Page 6
Figure 4: ImproX DPA Connected to the ImproX TT

XTT316-0-0-GB-08
December 2007
Page 7
NOTE: On powering up, the Antenna Reader’s Status LED will illuminate solid Red.
The Antenna Reader will not read Tags until configured in the Software.
Serial Number Label
1. Once the Antenna Reader is installed, sketch a rough site plan.
2. Attach the Antenna Reader’s loose Serial Number Label and the Controller,
Terminal or Receiver’s Fixed Address Label, to the sketched site plan in the
position of the Antenna Reader.
The Antenna Reader does not have its own Fixed Address. When connected to a
Controller, Terminal or Receiver the Antenna Reader is assigned one of the available
Fixed Addresses.
The Serial Number Label identifies the type of Antenna Reader, and the Fixed Address
Label (shipped with the Controller, Terminal or Receiver) identifies the Fixed
Addresses. Both these labels should be attached to the site plan to assist in identifying
the hardware once an Auto-ID is performed.
GUARANTEE OR WARRANTY
This product conforms to our Guarantee or Warranty details placed on our Web Site, to
read further please go to www.impro.net.
USER NOTES

XTT316-0-0-GB-08
December 2007
Page 8
This manual is applicable to the ImproX (DPA) 125kHz Door Entry Panel Antenna
Reader, XTT908-1-0-GB-01.(The last two digits of the Impro stock code indicate
the issue status of the product).
XTT316-0-0-GB-08
Issue 09
Dec
2007
ImproX DPA\English Manuals\LATEST ISSUE
\ImprXDPA-insm-en-09.docx