IN DEVICE POWER AD 2 User manual

POWER AD
Tool for embedding PK60
flush-mounted boxes
PL | EN
User Manual
POWER AD 3
POWER AD 4
POWER AD 5
POWER AD 2

Please read the Operator’s Manual!
Dear customers,
Thank you for choosing the IN DEVICE brand. We hope that our
product, which uses the latest technologies, will prove to be the
most satisfactory.
POWER AD is an innovative tool for embedding PK 60 type flush-
mounted boxes. Before using the tool, please read the manual.
When passing the product on to another user, please also pass on
these instructions. Please observe all warnings and information in
the operating manual.
Important information
and helpful tips for use
WARNINGS: Safety warnings
concerning life-threatening and
property damage.
Complies with
- the Machinery Directive 2006/42/EC Designed and manufactured in Poland
This tool was produced at modern and environment safety plant
without affecting nature.

TABLE OF CONTENT
1 Product Overview
1.1 General description
1.2 Use
1.3 Characteristics
1.4 Adjustment of the distance from the wall
1.5 Execution of POWER AD
2 Installation of PK60 boxes with POWER AD
2.1 Installation steps
2.2 Setting the position of the clamps
3 Technical Data
4 Safety and environmental protection
4.1 General safety rules
4.2 Storage
5 Transport, cleaning and maintenance
5.1 Maintenance
5.2 Storage
5.3 Handling and transportation
6 Disposal and scrapping
6.1 Disposal and scrapping
6.2 Product Packaging
3POWER AD - user manual
4
4
5
5
6
6
7
7
8
9
10
10
10
12
12
12
12
13
13
13

List of Power AD items
1 Base frame
2 Grip
3 Manual clamp
4 PK 60 Box clamp
5 Two-planes surface level
6 Level line
7 Mounting box 1
8 Mounting box 2
9 Hole for the bolt of PK60 box
10 Hole for foam application
11 Through - hole
12 Viewing hole for level setting
13 Adjusting the depth of embedding cans
14 Main through-hole for electric cables
1.1 General description
Product Description
3
1 5 2
8 7 9
13
6
10
412
10
10
1
14
4POWER AD - user manual
11
13
13
13
5
6

1.2 Use
Power AD is a tool
used for embedding
electrical boxes. It eliminates
problems related to the assembly of
PK60 electrical boxes. It is a tool that
facilitates assembly work and ensures
the highest standard of mounting the
boxes in the wall. It is available in a
version for 2, 3, 4 and 5 PK60 cans in a
linear arrangement. It enables
embedding horizontally and
vertically, as well as in plastered and
unfinished walls.
POWER AD is adapted to all types of
flush-mounted boxes available on the
market.
1.3 Characteristics
Electric cans, are
mounted in the tool with
proper system stiffness and linearity
position. The fastening process itself
takes place by inserting boxes in the
sockets and snapping the clamps.
In the event of dimensionally
defective batches of cans, or the
occurrence of unforeseen factors,
there is a possibility of additional
fastening of the can to the handle.
For this purpose, appropriate
openings were created to support the
mounting of the cans.
POWER AD eliminates
the occurrence of the oval of
cans. It is also used for assembly in
the case of using non-split boxes.
There are special holes in the base
frame structure through which the
electric wires are led. Additional
fastening of boxes with screws may
be useful in the case of a large
number of electric wires or defective
boxes.
The use of POWER AD tool does not
require the use of additional devices.
Indicators for horizontal or vertical
position in all planes are placed on
the tool.
Product Description
1
5POWER AD - user manual

Indicators for horizontal or vertical
position in all planes are placed on
the tool.
The setting of the levels is made
directly with the tool.
In addition, at the ends of the tool, on
both sides of the can axis, there are
viewing holes to help position the
tool parallel to the line drawn on the
wall.
Obtaining a common plane of the
wall and the front of the boxes is
carried out by pressing the tool
against the wall.
1.4 Adjustment of the
distance from the wall
It is possible to set the tool in such a
way that it automatically embeds the
boxes at the appropriate distance
from the wall to the thickness of the
plaster or glaze. Adjustments are
made with screws on the corners of
the tool.
1.5 Execution of POWER AD
POWER AD tool is made of materials
that ensure its durability in
demanding construction conditions.
The latest manufacturing
technologies make the tool light and
comfortable to use. Ease of use and
ergonomic shape guarantee
comfortable work. The tool contains
measuring instruments and is
calibrated. Loosening the elements
may result in out-of-calibration of the
tool. The appearance of the various
versions of the tool may differ.
Product Description
1
6POWER AD - user manual

2.1 Assembly steps
1. Preparation and making of the hole
in the wall for electrical boxes.
2. Fixing a row of boxes on POWER
AD tool.
The boxes should be put against the
tool frame in the socket between the
fixings.
The boxes are blocked by moving the
clamps (3) towards the boxes.
3. Passing through the electric cables
and fixing the boxes in the holes in
the wall.
Installation of PK60 boxes with POWER AD
2
7POWER AD - user manual

4. Embedding the boxes in the wall.
Setting the tool in the appropriate
position (vertical or horizontal).
5. Application of mounting foam
through the holes.
6. Releasing the clamps and pull out
the POWER AD in the upward
direction.
7. Finishing the wall surface.
NOTE - in order to correct
assembly, removal of the
POWER AD should take place after
the mounting foam has concentrated.
The time of the foam concentration
is given by the manufacturer.
8. After the work is done, the cleaned
tool should be stored in the box
provided by the manufacturer.
2.2 Setting the position of the
clamps
Set the clamps by regulating the nut
to distance as to properly press down
type of your can. Preferred dimension
13mm
Installation of PK60 boxes with POWER AD
2
8POWER AD - user manual

POWER AD is available in four variants depending on the number of boxes
installed at one time.
Below are the dimensions and weight of individual devices.
POWER AD 5 - installation of up to 5 boxes at the same time
POWER AD 4 - installation of up to 4 boxes at the same time
POWER AD 3 - installation of up to 3 boxes at the same time
POWER AD 2 - installation of up to 2 boxes at the same time
3Technical parameters
9POWER AD - user manual
POWER AD5 weight: 1,18kg
POWER AD4 weight: 1kg
POWER AD3 weight: 0,85kg
POWER AD2 weight: 0,7kg

This chapter includes
safety instructions that will
help you to protect against
personal injury or property
damage. Failure to follow these
instructions voids the granted
warranty.
1.1 General safety rules
Working with POWER AD tool,
and all intermediate work,
must take place with the power
supply of the electrical system in the
place of installation - switched off.
•The device complies with
international safety standards.
•The tool should be used in
accordance with the general principles
of occupational health and safety.
•Using POWER AD tool, the operator
must be wearing safety shoes and
work clothes.
•Adjustment must be made according
to the instructions and using approved
tools.
•The place of installation of the boxes
must be free of any random objects
within the operator's work area.
•Follow the correct order of work, as
described in the manual, to avoid
undesirable events.
•Dropping the tool can result in
injury, if safety shoes and work
clothes are not worn.
•POWER AD tool should be used by
one person only.
•The tool does not need to be
connected to the power supply.
•Works preceding and following the
use of POWER AD should be
performed taking into account the
principles of occupational health and
safety rules and using personal
protective equipment (safety glasses,
gloves, safety shoes, work clothes).
•The use of chemicals related to the
operation of the POWER AD tool
(mounting foam, gypsum or other)
should be in accordance with the
instructions of the manufacturers of
these substances and with respect to
health and safety rules.
4Safety and environmental protection
10POWER AD - user manual

•Be careful when inserting the PK60
boxes on the POWER AD sockets.
•Be careful when pushing the clamps
of the hand clamp.
•As listed in the section on cleaning
and maintenance, the device should be
cleaned with the use of appropriate
tools and cleaning agents.
•Use only original spare parts or those
recommended by the manufacturer.
•Keep the package with the tool out
of the reach of children.
•The tool may contain sharp edges
and metal filings on the surface.
•The tool should be stored and
transported in accordance with the
manufacturer's recommendations.
When transferring
electric cables, make sure
that the electrical system is not
plugged into the mains.
•The tool has been produced in
industrial conditions in compliance
with all safety conditions.
4.2 Storage
POWER AD tool is delivered from
the manufacturer in intermediate
unit packages or in a professional
box, depending on the type of
order.
4Safety and environmental protection
11POWER AD - user manual

5.1 Maintenance
The tool should be washed with
water and dried each time after use.
Scrape off the deposits with a copper
or a soft brass brush.
POWER AD does not require
additional security.
5.2 Storage
•If the device is not going to be
used for an extended period of
time, it should be stored in a safe
place.
•Remove the PK60 boxes and other
items that may have been used
during the deposition.
•Clean the device and dry it.
•Put POWER AD in a suitable place
in a case or a box.
•The device must be kept out of the
reach of children.
5.3 Handling and
transportation
•POWER AD should be handled and
transported in its original
packaging. It protects the tool
against physical damage.
•Do not place heavy loads on the
tool or package. This can damage
the entire tool or its components.
•If dropped, it may become out of
balance or permanently damaged.
•The POWER AD set includes a
carrying and storage case. The
suitcase is available for the entire
set or for each POWER AD size
separately.
5Transport, cleaning and maintenance
12POWER AD - user manual

6.1 Disposal and scrapping
Adopted constructional
solutions and high-quality
components allow for proper
operation of the device for about 10
years. Nevertheless, changes that may
occur much earlier, and cannot be
foreseen today, changes in the
Customer's needs, or changes in
regulations and standards, forcing the
equipment to be adapted or
withdrawn from use, may result in the
necessity of its utilization and
scrapping. This also applies to replaced
or repaired parts or assemblies of the
device. The buyer is obliged to
perform these activities in accordance
with the legal status in force at the
time and place.
All components of the tool
are allowed to be recycled.
6.2 Product Packaging.
Packaging of this tool
is made of materials that are
allowed to be recycled. Packaging
must be disposed of in accordance
with local environmental
regulations, so that all materials can
be recycled.
6Disposal and scrapping
13POWER AD - user manual