Polaris 2882167 User manual

APPLICATION
Verify accessory fitment at Polaris.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for.
Please retain these installation instructions for future reference and parts ordering
information.
KIT CONTENTS
This kit contains parts for installation of the rear audio harness only. Prior installation of the following additional
kits is also required (sold separately):
1. One of the following Battery Connection Kits:
• PN 2879862, 2881551, or equivalent (2 passenger RZR®)
• PN 2880055, 2881646, or equivalent (4 passenger RZR®)
2. Extreme Audio Pod Kit, PN 2881227
3. One or more of the following audio source components and any required harness(es):
• RIDE COMMAND™ 7” Display Kit, PN 2882068, RIDE COMMAND™ 7” Display Mount Kit, PN 2882069,
and Audio Adapter Kit, PN 2882534
• Interactive Digital Display 2.0, PN 2881554, and Interactive Digital Display Install Kit, PN 2880497
• Dash Radio Kit, PN 2881988
• Bluetooth®Remote Kit, PN 2881470
• Other equivalent audio source component
This Kit includes:
REF QTY PART DESCRIPTION PART NUMBER
1 1 Harness, Signal -
2 1 Harness, Power -
3 10 Cable Tie 7080492
1 Instructions 9927572
TOOLS REQUIRED
• Safety Glasses
• Pliers, Push Pin Rivet
• Screwdriver Set, Torx®
• Socket Set, Metric
IMPORTANT
Your Rear Audio Harness Kit is exclusively designed for your vehicle. Please read the installation instructions
thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to
ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.
ASSEMBLY TIME
Approximately 30–40 minutes
NOTE
Additional time may be required for optional steps, or
to accommodate other installed accessories.
Instr 9927572 Rev 01 2016-11 Page 1 of 4
P/N 2882167
REAR AUDIO HARNESS KIT

Instr 9927572 Rev 01 2016-11 Page 2 of 4
INSTALLATION INSTRUCTIONS
1. Shift vehicle transmission into “PARK”. Turn key to
“OFF” position and remove from vehicle.
2. Remove driver’s (or left rear passenger) seat and
disconnect black negative (-) cable from battery.
3. Gain Access.
NOTE
RZR XP®1000 shown; other vehicles similar.
a. Remove hood.
b. Remove windshield (if installed).
c. Remove two screws Asecuring front of upper
dash panel, then carefully pull panel rearward,
disengaging seven retaining clips Bas shown.
If necessary for access, label and disconnect
other electrical harnesses from control panel.
d. Remove center floor console.
TWO PASSENGER VEHICLES
Remove five push pin rivets Cand two screws
Das shown. Remove center console, pushing
boots for gear shift and seat belt through
console openings. Retain rivets and screws.
FOUR PASSENGER VEHICLES
i. Remove five push pin rivets Cand four
screws Dfrom front floor console as
shown. Remove console, pushing boots for
gear shift and seat belt through console
openings. Retain rivets and screws.
ii. Remove four push pin rivets Eand two
screws Ffrom rear floor console as shown.
Remove console, pushing boots for gear
shift and seat belt through console
openings. Retain rivets and screws.

Instr 9927572 Rev 01 2016-11 Page 3 of 4
4. Connect signal harness qand power harness w
to master audio pod (audio pods sold separately).
a. Join small 4–pin connector on signal harness
qto mating 4–pin connector on audio pod.
b. Join large 4–pin connector on power harness
wto mating 4–pin connector on audio pod.
5. Route signal harness qand power harness w.
NOTE
Harnesses shown in final secured configuration.
RZR XP®1000, RZR XP®TURBO
a. Route harnesses down RH C-pillar (4 Seat: D-
Pillar), then through gap between base of pillar
and body panel into wheel well.
NOTE
Vehicle shown with optional Subwoofer Kit PN
2882063 (sold separately).
b. Route harnesses forward along vehicle frame,
in front of air intake tube, then outboard along
frame (behind rear close-off panel).
c. Route harnesses down along vehicle frame
until below rear stabilizer bar attach points.
d. Route harnesses inboard to center console,
then forward through center console following
battery connection cables (sold separately).
NOTE
Harnesses will be secured to shift cable Gusing
cable tie e(see Step 7).

Instr 9927572 Rev 01 2016-11 Page 4 of 4
e. After exiting forward end of center console,
route harnesses up forward side of firewall to
under-hood compartment.
RZR®900, RZR®S 900, RZR®S 1000
a. Route harnesses down RH B-pillar (4 Seat: C-
Pillar), through gap between base of pillar and
body panel into wheel well, then down along
vehicle frame (behind rear close-off panel).
b. Route harnesses inboard to center console,
then forward through center console following
battery connection cables (sold separately).
c. After exiting forward end of center console,
route harnesses up forward side of firewall to
under-hood compartment.
6. Connect harnesses to terminal block and audio
source component.
a. Connect power harness wring terminals to
terminal block:
•RED harness wire: To post with existing RED
battery connection cable (unswitched 12V
POS); post may be identified as “BAT”
•BLACK harness wire: To post with existing
BLACK battery connection cable (12V NEG);
post may be identified as “GND”
b. Route 4–pin connector on signal harness q
and blue wire bullet connector on power
harness wfrom under-hood compartment
rearward through firewall grommet into upper
dash compartment, then join to corresponding
connectors on audio source component. See
Kit Contents for detail.
7. Secure signal harness qand power harness wto
battery connection cables in center console, and to
remainder of vehicle as shown in Step 5, using
cable ties e.
Prevent harness contact with hot components,
sharp edges, or moving parts. Coil and secure
excess harness length in upper dash
compartment.
8. Restore access. If other electrical harnesses were
disconnected in Step 3c. then reconnect them
now.
9. Reconnect black negative (-) cable to battery and
reinstall seat.
FEEDBACK FORM
A feedback form has been created for the installer to provide any comments, questions
or concerns about the installation instructions. The form is viewable on mobile devices
by scanning the QR code or by clicking HERE if viewing on a PC.
FEEDBACK FORM