6
GB
Turning on the Appliance
How to start a wash cycle…
Afterperforming all the operations describedinthe previous
paragraphs,turn the water tap oncompletelyand press ON-
OFF button "A": you will hear a short beep and indicator
light "B" lights up. At this point, the appliance is on and
ready to be programmed
Starting and selecting the cycle.
Turn thecycle selectorknob "D"clockwiseuntilthe reference
notch on the knob corresponds with the number or symbol
forthe cycle you wish to set (consult the wash cycle table on
page 7, especially when first using the appliance).
If the appliance door is shut, press the Start button "R" and
you will hear a beep; the cycle will start up within a few
seconds.
Cycle phase indicator lights
Thedishwasher is providedwith4indicator lights "G" which
come on in sequence as the appliance is performing that
specific phase of the wash cycle.
These phases are:
pre-wash, wash, rinses, drying
Cancelling or modifying a wash cycle in progress…..
Premise: You can cancel the wash cycle in progress, if it has
only just started.
To modify a wash cycle, keep the RESET button "R" pressed
for about 5 seconds: a prolonged beep will sound, followed
by three short beeps. Indicator light "G" will turn off and at
this point, all the settings will have been cancelled.
To select a new wash cycle, repeat the operations illustrated
in the paragraph entitled "starting and selecting the cycle".
If you have left out a dish…
You can interrupt a wash cycle by pressing the ON-OFF
button, then place the dishes you had left out into the
appliance, which will start up from where it was interrupted
when you turn it back on.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when the door is shut.
At the end of the wash cycle….
The end of the wash cycle is indicated by two short beeps
and the flashing of the drying phase indicator light.
• Press button "A" to turn the appliance off.
• Turn off the water tap.
• Wait a few minutes before unloading the dishes: if you
wait a little while, they dry better thanks to the steam.
• Empty the lower rack first.
Warning:whenyouopen thedishwasherdoorafterthewash
cycle has just ended or is under way, take care not to scald
yourself with the hot steam.
You decide when it starts.
When you have loaded the dishes, you can choose when to
start your dishwasher before setting the wash cycle desired.
Press button "H" to delay the start of the wash cycle by 12,
9, 6 or 3 hours. Each time you press it, you will hear a short
beep and the indicator light "G" corresponding to the
selected delay will light up.
Now you can select the desired wash cycle. Press the start
button "R" and after you hear the beep, the countdown to
the delayed start will begin.
Oncethis time is up, the indicator lightwillstopflashing and
the wash cycle will begin.
If you have set a 12 hour delay, for example, once you have
selected thewash cycle, the12 hourindicator lightwill flash
followedby the others in sequence until the set time delay is
up.A quicklook atthe indicator lightswill keepyou informed
of the countdown progress at all times.
Have you changed your mind?
If you change your mind, you can set a shorter time delay:
press button "H" to select it. You need not reset the wash
cycle.
If on the other hand you want to cancel the delay set and
you want the cycle to start immediately, press button "H"
repeatedly until the cycle starts and indicator light "G"
corresponding to the cycle start phase comes on.
Dual function of indicator lights "G"
1) flashing to indicate a delayed start: to remind you
that you have set a delayed start;
2) onand not flashing beneath the cycle phase symbol:
meaning the cycle has started and is in the phase indicated
by the symbol.
You want to wash on one rack only?
Remember to use half the amount of
detergent.
Yourdishwasher also allows you to wash half a load, to save
water and electricity. Before setting any wash cycle, press
button "I", the indicator light "L" lights up.
