Indesit win 110 User manual

1
GB
English,1
Contents
Installation, 2-3
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washing machine description, 4-5
Control panel
Leds
Starting and Programmes,
Briefly: how to start a programme
Programme table
Personalisations, 7
F nctions
Detergents and laundry, 8
Detergent dispenser
Preparing yo r la ndry
Special items
Precautions and advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
C tting off the water or electricity s pply
Cleaning yo r appliance
Cleaning the detergent dispenser
Caring for yo r appliance door and dr m
Cleaning the p mp
Checking the water inlet hose
Troubleshooting, 11
Service, 12
Before calling for Assistance
WASHING MACHINE
WIN 110
Instructions for use
GB
Nederlands,13
NL
Deutsch,25
DE
Français,37
FR
Românã,49
RO
Èeský,61
CZ
Espanol,73
ES

2
GB
Installation
Keep this instr ction man al in a safe place for
f t re reference. Sho ld the appliance be sold,
transferred or moved, make s re the instr ction
man al accompanies the washing machine to inform
the new owner as to its operation and feat res.
Read these instr ctions caref lly: they contain vital
information on installation, se and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged d ring transport. If this is the case, do not
install it and contact yo r retailer.
3. Remove the 3
protective screws and
the r bber washer with
the respective spacer,
sit ated on the rear of
the appliance (see
figure).
4. Seal the gaps sing the plastic pl gs provided.
5. Keep all the parts: yo will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
1. Install the washing machine on a flat st rdy floor,
witho t resting it p against walls, f rnit re cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any nevenness
by tightening or
loosening the adj stable
front feet (see figure);
the angle of inclination,
meas red according to
the worktop, m st not
exceed 2°.
Levelling yo r appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
d ring operation. If it is placed on a fitted or loose
carpet, adj st the feet in s ch a way as to allow
eno gh room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the s pply
pipe by screwing it to a
cold water tab sing a
3/4 gas threaded
connection (see figure).
Before performing the
connection, allow the
water to r n freely ntil
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, sit ated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make s re there are no kinks or bends in the hose.
The water press re at the tap m st be within the
val es indicated in the Technical details table
(on the next page).
If the water inlet hose is not long eno gh, contact
a specialist store or an a thorised serviceman.
Never se hoses that have already been sed.

3
GB
Connecting the drain hose
Connect the drain hose,
witho t bending it, to a
draining d ct or a wall
drain sit ated between
65 and 100 cm from
the floor;
alternatively, place it
over the edge of a
basin, sink or t b,
fastening the d ct
s pplied to the tap (see
figure). The free end of
the hose sho ld not be
nderwater.
 We advise against the se of hose extensions; in
case of absol te need, the extension m st have the
same diameter as the original hose and m st not
exceed 150 cm in length.
Electric connection
Before pl gging the appliance into the mains
socket, make s re that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to s stain the appliance's
maxim m power load indicated in the Technical
details table (on the right);
 the s pply voltage is incl ded within the val es i
ndicated on the Technical details table
(on the right);
 the socket is compatible with the washing
machine's pl g. If this is not the case, replace
the socket or the pl g.
 The washing machine sho ld not be installed in an
o tdoor environment, not even when the area is
sheltered, beca se it may be very dangero s to
leave it exposed to rain and th nderstorms.
 When the washing machine is installed, the mains
socket m st be within easy reach.
 Do not se extensions or m ltiple sockets.
 The power s pply cable m st never be bent or
dangero sly compressed.
 The power s pply cable m st only be replaced by
an a thorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
yo se it for the first time, r n a wash cycle with
detergent and no la ndry, setting the 90°C
programme witho t a pre-wash cycle.
65 - 100 cm
Technical details
Model WIN 110
Dimensions
59.5 cm wide
85 cm high
52,5 cm deep
Capacity from 1 to 5 kg
Electric
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maxim m press re 1 MPa (10 bar)
minim m press re 0.05 MPa (0.5 bar)
dr m capacity 46 litres
Spin speed p to 1100 rpm
Control
programmes
according to
EN 045
directive
programme 3;
r n with a load of 5 kg.
This appliance is compliant with the
following E ropean Comm nity
Directives:
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
s bseq ent amendments
- 2006/95/CE (Low Voltage)
- 2002/96/CE

4
GB
Washing machine description
Control panel
Detergent dispenser
ON-OFF
B tton
START/RESET
B tton
PROGRAMME
Knob
Leds
FUNCTION
B ttons
ON-OFF/
DOOR
LOCK
Led
Detergent dispenser: to add detergent and fabric
softener (see page 8).
LEDS: to find o t which wash cycle phase is nder
way.
FUNCTION b ttons: to select the f nctions
available. The b tton corresponding to the f nction
selected will remain on.
START/RESET b tton: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK Led: to find o t whether the
washing machine is on and if the appliance door can
be opened (see page 5).
ON/OFF b tton: to t rn the washing machine on
and off.
PROGRAMME knob: to select the wash
programmes. The knob stays still d ring the cycle.
Standby mode
This washing machine, in compliance with new
energy saving reg lations, is fitted with an a tomatic
standby system which is enabled after abo t 30
min tes if no activity is detected. Press the ON-OFF
b tton briefly and wait for the machine to start p
again.

5
GB
ON-OFF/DOOR LOCK led
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before yo open the appliance door.
 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality (see page 11).
Leds
The LEDS provide important information.
This is what they can tell yo :
Cycle phase under way:
D ring the wash cycle, the LEDs grad ally ill minate
on to indicate the cycle phase nder way:
Wash
Rinse
Spin cycle
Note: d ring draining, the LED corresponding to the
Spin cycle phase will be t rned on.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a f nction is selected, the corresponding
b tton is ill minated.
If the f nction selected is incompatible with the
programme set, the b tton will flash and the
f nction will not be enabled.
If yo set a f nction that is incompatible with
another f nction yo selected previo sly, only the
last one selected will be enabled.