Indesit WITP 82 User manual

1
GB
WASHING MACHINE
WITP 82
Instructions for use
Contents
Installation, 2-
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
How to open and shut the dru , 5
Leds, 5
Starting and Programmes, 6
Briefly: how to start a progra e, 6
Progra e table, 6
Personalisations, 7
Setting the te perature, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Bleach cycle, 8
Preparing your laundry, 8
Special ite s, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environ ent, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Caring for your appliance door and dru , 10
Cleaning the pu p, 10
Checking the water inlet hose, 10
Cleaning the detergent dispenser, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
ES
English, 1
GB
Magyar, 13
ES
HU
Românã, 49
RO
Polski, 61
ES
PL
CZ
Èeský, 25
Slovenský, 37
SK

2
GB
Keep this instruction anual in a safe place for
future reference. Should the appliance be sold,
transferred or oved, ake sure the instruction
anual acco panies the washing achine to infor
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
infor ation on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing
achine.
2. Check whether the
washing achine has
been da aged during
transport. If this is the
case, do not install it
and contact your
retailer.
3. Re ove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need the again if the
washing achine needs to be oved to another
location.
Warning: should the screws be re-used, ake sure
you fasten the shorter ones at the top.
Packaging aterials are not children's toys.
Levelling
Your achine ay ake a considerable a ount of
noise if the two front feet have not been adjusted
correctly.
1. Install the washing
achine on a flat sturdy
floor, without resting it
up against walls,
furniture cabinets or
other.
2. If the floor is not
perfectly level, co pen-
sate for any
unevenness by
tightening or loosening
the adjustable front feet (see figure); the angle of
inclination, easured according to the worktop,
ust not exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough roo for ventilation beneath the washing
achine.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into
the end of the inlet
hose and screw the
latter onto a cold
water tap with a 3/4
gas threaded outh
(see figure).
Before aking the
connection, allow the
water to run freely
until it is perfectly
clear.
2. Connect the other
end of the water inlet
hose to the washing
achine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap ust be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough,
contact a specialist store or an authorised
service an.
Installation
A

GB
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 c fro
the floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
 We advise against the use of hose extensions; in
case of absolute need, the extension ust have the
sa e dia eter as the original hose and ust not
exceed 150 c in length.
Electric connection
Before plugging the appliance into the ains
socket, ake sure that:
 the socket is earthed and in co pliance with the
applicable law;
 the socket is able to sustain the appliance's
axi u power load indicated in the Technical
details table (on the right);
 the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
 the socket is co patible with the washing
achine's plug. If this is not the case, replace
the socket or the plug.
 The washing achine should not be installed in an
outdoor environ ent, not even when the area is
sheltered, because it ay be very dangerous to
leave it exposed to rain and thunderstor s.
 When the washing achine is installed, the ains
socket ust be within easy reach.
 Do not use extensions or ultiple sockets.
 The power supply cable ust never be bent or
dangerously co pressed.
 The power supply cable ust only be replaced by
an authorised service an.
Warning! The co pany denies all liability if and when
these nor s are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first ti e, run a wash cycle with
detergent and no laundry, setting the 90°C
progra e without a pre-wash cycle.
65 - 100 cm
Technical details
Model WITP 82
Dimensions
40 c wide
85 c high
60 c deep
Capacity fro 1 to 5 kg
Electric
connections
voltage 220/230 Volts 50 Hz
axi u absorbed power 1850 W
Water
connections
axi u pressure 1 MPa (10 bar)
ini u pressure 0.05 MPa (0.5 bar)
dru capacity 42 litres
Spin speed up to 800 rp
Control
programmes
according to
IEC456 directive
progra e 2; te perature 60°C;
run with a load of 5 kg.
This appliance is co pliant with the
following European Co unity
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent a end ents
- 89/336/CEE of 03/05/89
(Electro agnetic Co patibility) and
subsequent a end ents
- 2002/96/CE

4
GB
ON-OFF/LID LOCK led:
If this LED is on, the appliance Lid is locked to prevent it fro being opened accidentally; to avoid any
da ages, you ust wait for the la p to flash before you open the Lid.
.
 The rapid flashing of the ON-OFF/LID LOCK Led together with the flashing of at least one other LED indicates
there is an abnor ality (see pages 11-12 Troubleshooting).
Control panel
Washing machine description
START/STOP
button
TEMPERATURE
knob
START/RESET
button
FUNCTION
Buttons
PROGRAMME
knob
LEDs
LID LOCKED
LED
Detergent dispenser to add detergent and fabric
softener (see page 8).
LEDs to find out which wash cycle phase is under way.
(see page 5).
FUNCTION keys to select the functions available.
The button corresponding to the function selected will
re ain on.
TEMPERATURE knob to set the te perature or the cold
wash cycle (see page 7).
ON/OFF key to turn the washing achine on and
off.
START/RESET key to start the progra es or
cancel incorrect settings.
ON-OFF/LID LOCK LED, to find out whether the
washing achine is on (flashing) and if the lid ay be
opened (see page 4).
PROGRAMME knob to set the progra es
(see page 6).
The knob stays still during the cycle.

5
GB
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Fig. 3 Fig. 4
Fig. 1 Fig. 2
A) Opening (Fig. 1).
Lift the external lid and open it co pletely.
B) Then open the drum using both hands as
shown in Fig. 2:
- press the button indicated by the arrow in Fig. 2
lightly downwards, with one hand fir ly resting on
the doors to prevent the fro suddenly opening
and hurting your fingers;
- therefore follow the appliance doors along as these
unhook and open easily.
C) Loading the washing machine. (Fig. ).
D) Shutting (Fig. 4).
- close the dru fully by first shutting the front door
followed by the rear one;
- then ensure the hooks on the front door are perfectly
housed within the seat of the rear door;
- after the hooks have clicked into position, press both
doors lightly downwards to ake sure they do not
co e loose;
- finally shut the external lid.
How to open and to close the drum
Cycle phase under way:
During the wash cycle, the LEDs gradually illu i-
nate on to indicate the cycle phase under way:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the LED corresponding to
the Spin cycle phase will be turned on.
Leds
The LEDS provide i portant infor ation.
This is what they can tell you:
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illu inated.
If the function selected is inco patible with the
progra e set, the button will flash and the function
will not be enabled.
If you set a function that is inco patible with another
function you selected previously, only the last one
selected will be enabled.