INDUCS Modul Line 360 R 1x5 kW Operating manual

1
Modul Line
Modular system for induction cooking
User and Installation Manual
CAUTION: Read the instruction before using the machine.
WARNING: If the surface is cracked, immediately disconnect the appliance from supply.
Notice: This Unit is approved for professional use only.
Models
Modul Line 360 R 1x5 kW
Modul Line XXX R 2x3.5 / 5 kW
Modul Line 500 R 1x5 kW
Modul Line XXX Q 2x5kW
Modul Line Wok 1x5 kW
Modul Line XXX F 2x5 / 7 kW
Modul Line 360 R 2x3.5 / 5 kW
Modul Line XXX R 4x3.5 / 5 kW
Modul Line 360 R 4x3.5 / 5 kW
Modul Line XXX Q 4x5kW
Modul Line 360 R 4x3.5 / 5 kW
Modul Line XXX F 4x5 / 7 kW
Modul Line 360 F 1x5 / 7 kW
Modul Line XXX R 2x3.5 & F 2x7 kW
Modul Line 360 F 2x5 / 7 kW
Modul Line XXX R 2x5 & F 2x7 kW
Modul Line 400 ALC 1x5 kW
Modul Line 400 ALC 2x5 kW
Modul Line Pano 2x2.5 kW
Modul Line Pano 4x2.5 kW
Translation of Original Instruction –English
Modul Line X2 User and Installation Manual rev03 09/23

2
READ THIS MANUAL
Warning
Read this manual thoroughly before installing, operating, or performing maintenance on the equipment.
Failure to follow instructions in this manual can cause property damage, injury or death.
This manual must always be available for reference at the place of operation.
This manual is intended for kitchen consultants, cabinet designers, fabricators, installers, owners and
operators of our appliances.
Owners, consultants, fabricators and designers:
In order for the appliance to function safely and normally, you must read and understand all specific
and critical requirements (such as location, ventilation, clearance) when designing the location and/or
the electrical cabinet for the appliance.
Installers, operators and staff:
For your safety and safety of the others, you must follow all safety instructions during installation,
operation and maintenance of the equipment.
Should you require technical assistance, call your authorized service agent or distributor.
Always have the model and serial number available when you call.
Your Authorized Service Company and Contact Information
Your Equipment Supplier and Contact Information
Model Number
Serial Number
Date of Installation

3
ABOUT THIS MANUAL
Throughout this manual, the induction appliance model indicated on the cover page is referred to as
appliance, induction appliance or equipment.
A period (.) is used in this manual as the decimal separator.
Original measurements are in metrics. Measurements in imperial are provided for reference.
Not ALL models, options and accessories are available in all geographical regions. Please consult your
equipment supplier for the availability of the specific products in your region.
INSPECT THE SHIPMENT
Thoroughly inspect the equipment upon delivery. Immediately report to the delivery carrier, any damage that
occurred during transportation and request for a written inspection report from a claim adjustor.
Keep all packaging.
KEEP THE DELIVERY NOTE
The delivery note attached to the shipment contains detailed information on all components. Keep the
delivery note for reference.

4
Safety Notices
Safety Notices
DEFINITIONS
DANGER
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
This applies to the most extreme situations.
Warning
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
Caution
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
Notice
Indicates information considered important and is used to address practices not related to physical injury.
For example, messages relating to property damage.
NOTE: Indicates useful, extra information about the action you are performing.
Reference: ANSI Z535.6-2011
SAFETY SYMBOLS AND WARNINGS ON THE APPLIANCE
This symbol alerts you to a hazardous situation that WILL or COULD cause serious bodily harm or death. Be
alert and implement relevant safety precautions.
DANGER −HIGH VOLTAGE
This dangerous voltage warning symbol indicates a risk of electric shock and hazards from dangerous voltage.
Electromagnetic Field
This symbol warns against non-ionizing electromagnetic radiation.
Equipotential bonding
This symbol marks the terminal which must relate to the equipotential bonding system.
Warning
RISK OF FIRE OR ELECTRIC SHOCK! DO NOT OPEN!
To reduce the risk of fire or electric shock, do not remove or open cover.
Refer servicing to qualified personnel.
DANGER
Disconnect from supply circuit before opening.

5
Safety Notices
DISCLAIMERS
DANGER
Disregarding any safety instructions may cause harm to people, the surroundings, and the equipment. The
manufacturer and/or authorized representative are not responsible for any damages or personal injury
caused by failure to observe any safety instructions.
Risks involved when disregarding safety instructions include, but not limiting to:
• Death or injury caused by electric shock.
• Burn injury caused by contacting hot cooking surface, cookware, or oil and grease.
• Damage to the equipment caused by using unsuitable cookware.
DANGER
Do not install or operate equipment and/or accessories that have been misused, abused, neglected, damaged,
or altered from that of original manufactured specifications.
DANGER
Contact the manufacturer if you intend to make any changes on the equipment. For safety reasons, always
use genuine parts and accessories approved by the manufacturer or authorized representative. Refer to the
warranty documents for your equipment.
DANGER
Owners and operators are cautioned that maintenance and repairs must be performed by an authorized
service agent using only genuine replacement parts. The manufacturer will have no obligation with respect to
any product that has been improperly installed, adjusted, operated or not maintained in accordance with
national and local codes and/ or installation instructions provided with the product or any product that has
its serial number defaced, obliterated or removed, and/or which has been modified or repaired using
unauthorized parts or by unauthorized service agents.
DANGER
Improper installation, adjustment, alteration, service, or maintenance of this appliance or installation of a
damaged appliance can result in DEATH, INJURY, EQUIPMENT DAMAGE, and void the warranty.
DANGER
All power connections and fixtures must be maintained in accordance with local and national codes.
Warning
Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
Never use flammable oil-soaked cloths or combustible cleaning solutions for cleaning.
Warning
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision concerning use of
the appliance by a person responsible for their safety. Do not allow children to play with this appliance.

6
Safety Notices
Warning
This product contains chemical known to the State of California to cause cancer and/ or birth defects or other
reproductive harm. Operation, installation, and servicing of this product could expose you to airborne
particles of glass-wool or ceramic fibers, crystalline silica, and/or carbon monoxide. Inhalation of airborne
particles of glass-wool or ceramic fibers is known to the State of California to cause cancer. Inhalation of
carbon monoxide is known to the State of California to cause birth defects or other reproductive harm.
Warning
Authorized Service Representatives are obligated to follow industry standard safety procedures, including,
but not limited to, local/ national regulations for disconnection / lock out / tag out procedures for all utilities
including electric, gas, water, and steam.
Notice
This appliance is not approved or authorized for home or residential use but is intended for commercial
applications only. The manufacturer and/or authorized representative will not provide service, warranty,
maintenance, or support of any kind other than in commercial applications.
Notice
Routine adjustments and maintenance procedures outlined in this manual are not covered by the warranty.
NOTE: Proper installation, care and maintenance are essential for maximum performance and trouble-free
operation of your equipment. Visit our website for manual updates, translations, or contact information for
service agents in your area.
CORRECT DISPOSAL OF THIS PRODUCT
This marking shown on the product indicates that the product should not be disposed as
household waste or regular commercial waste. Instead, it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed correctly, you will help prevent potential harm to the environment or
human health, which could otherwise be caused by inappropriate waste handling of this
product.
For more detailed information regarding recycling of the product, please contact your local city office or
your waste disposal service.
NOTE: The appliance is built with common electrical, electromechanical, and electronic parts. No batteries
are used.
NOTE: The owner and operator are responsible for the proper and safe disposal of the appliance.
Important
Additional Safety Notices are stated in the relevant sections throughout the manual.

7
Table of Contents
Safety Notices .............................................................................................................................. 4
DEFINITIONS.................................................................................................................................... 4
SAFETY SYMBOLS AND WARNINGS ON THE APPLIANCE................................................................. 4
DISCLAIMERS ................................................................................................................................... 5
CORRECT DISPOSAL OF THIS PRODUCT........................................................................................... 6
Table of Contents......................................................................................................................... 7
Section 1.................................................................................................................................... 10
General Information................................................................................................................... 10
Description of Product ...................................................................................................................... 10
Application......................................................................................................................................... 10
Compliances ...................................................................................................................................... 11
Serial Plate Location.......................................................................................................................... 11
Model number and serial number .................................................................................................... 12
Product overview .............................................................................................................................. 12
GENERATORS................................................................................................................................. 12
OPERATIONS.................................................................................................................................. 13
Mounting frame ............................................................................................................................ 15
Further Options ............................................................................................................................. 15
Section 2.................................................................................................................................... 16
Installation................................................................................................................................. 16
INSTALLATION SAFETY − DISCLAIMER........................................................................................... 16
INSTALLATION SAFETY—CLEARANCE AND VENTILATION............................................................. 16
INSTALLATION SAFETY—ELECTRICAL ............................................................................................ 17
PERSONAL PROTECTION................................................................................................................ 18
Scope of delivery ............................................................................................................................... 19
Crucial components....................................................................................................................... 19
Interchangeable components ....................................................................................................... 19
Optional components.................................................................................................................... 19
Specifications - Dimensions............................................................................................................... 20
Generator Set-up 1........................................................................................................................ 36
Generator Set-up 2........................................................................................................................ 37
Generator Set-up 3........................................................................................................................ 38
Control-unit ................................................................................................................................... 38

8
Control-unit 4xRJ45....................................................................................................................... 39
Operation Options......................................................................................................................... 40
Electrical Connections ....................................................................................................................... 43
Generator ...................................................................................................................................... 43
General.......................................................................................................................................... 44
Generator setup (DIP switch settings)........................................................................................... 45
System cabling............................................................................................................................... 61
Connecting Operations options..................................................................................................... 71
Electrical Specifications..................................................................................................................... 75
ELECTRICAL CABLES....................................................................................................................... 75
INSTALLATION CLEARANCE ........................................................................................................... 75
OPERATING CONDITIONS.............................................................................................................. 75
Installation Instructions Modul Line.................................................................................................. 76
Installation with mounting frame.................................................................................................. 76
Installation instructions, coil carrier/coils..................................................................................... 77
Installation instructions, control unit............................................................................................ 77
Installation instructions, controls.................................................................................................. 77
Replacement or Servicing of the coil carrier ................................................................................. 77
Replacement or Servicing of the generator .................................................................................. 77
Ventilation Requirements ............................................................................................................. 78
Installation example ...................................................................................................................... 79
COMMISSIONING .......................................................................................................................... 80
Section 3.................................................................................................................................... 81
Operation .................................................................................................................................. 81
OPERATION SAFETY—DISCLAIMER ............................................................................................... 81
OPERATION SAFETY—PERSONAL PROTECTION ............................................................................ 81
Cooking with Induction ................................................................................................................. 83
Functionality...................................................................................................................................... 84
VARIABLE INDUCTION PARAMETERS ............................................................................................ 84
POSSIBLE EFFECTS ON COOKING BEHAVIOR................................................................................. 84
Important Rules—Operation and Maintenance ............................................................................... 85
Proper Induction Cookware .............................................................................................................. 86
CONDITION.................................................................................................................................... 86
MATERIAL ...................................................................................................................................... 86
BOIL TEST....................................................................................................................................... 87
SIZE OF PAN................................................................................................................................... 87

9
Rotary power switch.......................................................................................................................... 89
Tap-Operation Unit ........................................................................................................................... 89
Tap-Operation Unit Display (Overview) ........................................................................................ 90
Control............................................................................................................................................... 91
TURN UNIT ON............................................................................................................................... 91
LED RING........................................................................................................................................ 91
SWITCHING BETWEEN COOKING AND HOLDING MODES............................................................. 91
SETTING POWER LEVEL (1 TO 12) AND LOCK/UNLOCK................................................................. 91
Power Level Settings ..................................................................................................................... 91
SELECTING HOLD TEMPERATURE AND LOCK/UNLOCK................................................................. 91
SETTING THE TIMER....................................................................................................................... 92
TURNING OFF THE UNIT................................................................................................................ 92
Additional Settings ........................................................................................................................ 92
Automatic Pan Detection, No Pan No Heat................................................................................... 93
When the application is not in use................................................................................................ 93
Decommissioning .......................................................................................................................... 93
Section 4.................................................................................................................................... 94
Maintenance.............................................................................................................................. 94
MAINTENANCE SAFETY—DISCLAIMER.......................................................................................... 94
DANGEROUS ELECTRICAL VOLTAGE.............................................................................................. 94
MAINTENANCE SAFETY—CLEANING ............................................................................................. 94
Daily Cleaning and Maintenance....................................................................................................... 95
GLASS CLEANING........................................................................................................................... 95
VISUAL INSPECTION OF SILICONE SEAL......................................................................................... 95
Weekly Cleaning and Maintenance................................................................................................... 95
Yearly Maintenance........................................................................................................................... 95
Section 5.................................................................................................................................... 96
Troubleshooting......................................................................................................................... 96
DANGEROUS ELECTRICAL VOLTAGE.............................................................................................. 96
Common Problems............................................................................................................................ 96
Symptoms.......................................................................................................................................... 96
Boil Test............................................................................................................................................. 97
Avoiding dangers in case of accidents or malfunctions .................................................................... 97
Troubleshooting without Error Code ................................................................................................ 98
Troubleshooting –Error Code......................................................................................................... 100

10
Section 1
General Information
Description of Product
Built with a robust construction, our induction appliances are compact and powerful with the revolutionary
RTCSmp® Technology (Realtime Temperature Control System). The RTCSmp® Technology monitors
continuously in real time, the energy supply, temperature of the cook zone and the state of the components
such as the induction coil. This monitoring system ensures the most efficient energy transfer, as
well as maximizes safety:
•Safety functions such as Pan Detection and Boil Dry Protection are therefore guaranteed.
•The appliance starts heating only when a pan is placed in the cook zone.
•When a malfunction occurs, the integrated fault diagnostic system reports the malfunction instantly.
Synchrotec offers our customers:
•Absolute flexibility in your range planning
•All hobs are synchronised with each other, there is no interference whatsoever
•Regardless of the number of hobs, the induction adjusts itself the used pan material
•Four different operating concepts can be selected
•Extended selection of application solutions
PowerBoost offers our customers:
•The power of a hob can be increased automatically by up to 20% so that the maximum available energy
is available in the start-up cooking phase.
InnovativElectronicElements offers our customers:
•Due to the latest electronic components, it is possible to greatly reduce the waste heat, which leads to an
increased service life of the electronics.
•Unprecedented efficiency is achieved through state-of-the-art components
•Most powerful generator in this size
Connectivity* offers our customers:
•Control over kitchen processes
•Warning against misuse
•Remote maintenance
•Remote diagnosis
•Preventive service
•IoT ready
* Available as an option
Application
The Modul Line induction units are designed for installation in a closed stove or counter. Many applications
throughout the day with your appliance are possible, such as cooking, warming up, keeping warm, and
roasting of food:
•Thanks to RTCSmp temperature control happens instantly.
•With inductive energy transmission, your cookware can be heated very quickly.
•High power is possible for braising application and quick sauté.
•High power also means you can heat up a bigger pot quickly.
NOTE: To guarantee the reliability and performance of the appliance, you must use the recommended types
and sizes of pans with the appliance. See section 3 Operation.

11
General Information Section 1
Compliances
The units comply the latest Norms:
Europe models
• EN 55014-1
• EN 55014-2
• EN 60529
• EN 62233 (EMC/ EMV)
• EN 60335-1
• EN 60335-2-36
• EN 61000-3-11
• EN 61000-3-12
Serial Plate Location
The serial plate is located on top of the black housing of the unit. It specifies the model number, serial number,
and electrical specifications of the appliance.

12
General Information Section 1
Model number and serial number
The model and serial numbers are located on the nameplate. This manual applies only to the models
listed on the front of this manual.
READING THE MODEL NUMBER
[Model Name] [Glass Size] [Coil Type] [Power]
Model Name
Glass Seizes
Coil Type
Power
Modul Line
360 = 360x360mm
500 = 500x500mm
ALC = 200x400mm
ALC = 400x400 mm
PANO = 250x500 mm
PANO = 500x500 mm
650 = 650x650 mm
720 = 720x720 mm
R = round coil
Wok = wok coil
Q = quad coil
ALC = à la carte coil
F = full area coil
1x5 kW = 1 cooking zone with 5 kW
2x3.5 kW = 2 cooking zones; 3.5 kW
per zone
2x5 kW = 2 cooking zones; 5 kW per
zone
2x7 kW = 2 cooking zones; 7 kW per
zone
Product overview
GENERATORS
Available models
Power
per zone
(in kW)
Glass seizes
(in mm)
Glass
type
Coil
type
Nominal Voltage
Modul Line 360 R 1x5 kW
5
360 x 360
R
R
3 x 380 - 415
Modul Line 500 R 1x5 kW
5
500 x 500
R
R
3 x 380 - 415
Modul Line Wok 1x5 kW
5
Ø300
Cuvette
Wok
3 x 380 - 415
Modul Line 360 R 2x3.5 kW
3.5
360 x 360
R
R
3 x 380 - 415
Modul Line 360 R 2x5 kW
5
360 x 360
R
R
3 x 380 - 415
Modul Line 360 R 4x3.5 kW
3.5
360 x 360
R
R
3 x 380 - 415
Modul Line 360 R 4x5 kW
5
360 x 360
R
R
3 x 380 - 415
Modul Line 360 F 1x7 kW
7
360 x 360
F
F
3 x 380 - 415
Modul Line 360 F 2x5 kW
5
360 x 360
F
F
3 x 380 - 415
Modul Line 360 F 2x7 kW
7
360 x 360
F
F
3 x 380 - 415
Modul Line 400 ALC 1x5 kW
5
200 x 400
R
ALC
3 x 380 - 415
Modul Line 400 ALC 2x5 kW
5
400 x 400
R
ALC
3 x 380 - 415
Modul Line PANO 2x2.5 kW
2.5
250 x 500
R
R
3 x 380 - 415
Modul Line PANO 4x2.5 kW
2.5
250 x 1000
R
R
3 x 380 - 415
Modul Line 650 R 2x3.5 kW
3.5
375 x 650
R
R
3 x 380 - 415
Modul Line 650 R 2x5 kW
5
375 x 650
R
R
3 x 380 - 415
Modul Line 650 Q 2x5 kW
5
375 x 650
R
Q
3 x 380 - 415
Modul Line 650 F 2x5 kW
5
375 x 650
F
F
3 x 380 - 415
Modul Line 650 F 2x7 kW
7
375 x 650
F
F
3 x 380 - 415
Modul Line 650 R 4x3.5 kW
3.5
650 x 650
R
R
3 x 380 - 415
Modul Line 650 R 4x5 kW
5
650 x 650
R
R
3 x 380 - 415
Modul Line 650 Q 4x5 kW
5
650 x 650
R
Q
3 x 380 - 415
Modul Line 650 F 4x5 kW
5
650 x 650
F
F
3 x 380 - 415
Modul Line 650 F 4x7 kW
7
650 x 650
F
F
3 x 380 - 415
Modul Line 720 R 2x3.5 kW
3.5
360 x 720
R
R
3 x 380 - 415
Modul Line 720 R 2x5 kW
5
360 x 720
R
R
3 x 380 - 415
Modul Line 720 Q 2x5 kW
5
360 x 720
R
Q
3 x 380 - 415
Modul Line 720 F 2x5 kW
5
360 x 720
F
F
3 x 380 - 415
Modul Line 720 F 2x7 kW
7
360 x 720
F
F
3 x 380 - 415
Modul Line 720 R 4x3.5 kW
3.5
720 x 720
R
R
3 x 380 - 415

13
Modul Line 720 R 4x5 kW
5
720 x 720
R
R
3 x 380 - 415
Modul Line 720 Q 4x5 kW
5
720 x 720
R
Q
3 x 380 - 415
Modul Line 720 F 4x5 kW
5
720 x 720
F
F
3 x 380 - 415
Modul Line 720 F 4x7 kW
7
720 x 720
F
F
3 x 380 - 415
Modul Line Griddle 2x3.5 kW
3.5
580 x 620*
N/A
N/A
3 x 380 - 415
Modul Line Griddle 2x5 kW
5
580 x 620*
N/A
N/A
3 x 380 - 415
Modul Line Kombi 2x5 kW –65
5
580 x 620*
N/A
N/A
3 x 380 - 415
Modul Line Kombi 2x5 kW –100
5
580 x 620*
N/A
N/A
3 x 380 - 415
* Frying surface for Griddle and Kombi
Operating conditions
Max. tolerance of the mains voltage Nominal voltage +6% / -10%
Network impedance (Zmax.) 0,25 Ω
Frequency 50 / 60 Hz
Protection class IP X0
Min. pan diameter 12 cm
OPERATIONS
Available models
Description
Features
Potentiometer
This operation consists of a
rotary switch which lock in the
0 position and an LED
Controls one cooking zone
Cooking levels 1-12
Pot recognition feedback (LED)
Error codes (via LED flashes)
Tap Operation Single (with
front panel)
This operation consists of 1
knob and a display unit with
front panel, for overlying
mounting.
Controls one cooking zone
Pictogram display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap Operation Single
(without front panel)
This operation consists of 1
knob and a display unit
without front panel, for direct
integration into a stove
construction.
Controls one cooking zone
Pictogram display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap Operation (with front
panel)
This operation consists of 2
knobs and a display unit with
front panel, for overlying
mounting.
Controls two cooking zones
Pictogram display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap Operation (without front
panel)
This operation consists of 2
knobs and a display unit
without front panel, for direct
Controls two cooking zones
Pictogram display
Pot recognition feedback

14
integration into a stove
construction.
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap basic (horizontal)
This operation consists of 1
knob and a separate 7
segment Display for mounting
under the ceramic glass. The 7-
segment display has a
horizontal orientation.
Controls one cooking zone
7-segment display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap basic (vertical)
This operation consists of 1
knob and a separate 7 segment
Display for mounting under the
ceramic glass. The 7-segment
display has a vertical
orientation.
Controls one cooking zone
7-segment display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Tap plus (1 Poti, 1 Display)
This operation consists of 1
knob and a separate one OLED
Display for separate mounting.
Controls one cooking zone
OLED display
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Quick fix recommendations (errors)
Can be customized with local language
Tap plus (2 Poti, 1 Display)
This operation consists of 2
knob and a separate one OLED
Display for separate mounting.
Controls two cooking zones
OLED display (split screen)
Pot recognition feedback
Cooking levels 1-12
Temp. control 25 –100 °C
Timer function 0.5 –240 min
Lock function
Limitation of max. power output
Customization of LED-Ring colour
Error codes are displayed
Quick fix recommendations (errors)
Can be customized with local language

15
General Information Section 1
Mounting frame
Available models (in mm)
Description
Installation-mounting frame 360x360
For one cooking zone (R/F)
Installation-mounting frame 500x500
For one cooking zone (R)
Installation-mounting frame 200x400
For one cooking zone (ALC)
Installation-mounting frame 400x400
For two cooking zones (ALC)
Installation-mounting frame 250x500
For two cooking zones (PANO)
Installation-mounting frame 250x1000
For four cooking zones (PANO)
Installation-mounting frame 375x650
For two cooking zones (R/Q/F)
Installation-mounting frame 650x650
For four cooking zones (R/Q/F)
Installation-mounting frame 360x720
For two cooking zones (R/Q/F)
Installation-mounting frame 720x720
For four cooking zones (R/Q/F)
Installation-mounting frame Griddle/Kombi
For Griddle and Kombi Plates
Further Options
Available models
Description
Grease filter
Air filter to protect the generator from grease ingress
Grease filter frame
Frame to mount and hold the grease filter.
Cable kit with 4m length
Cable kit for situations in which the generator is place up to
4m away from the coil carrier sheet
Cable kit with 6m length
Cable kit for situations in which the generator is place up to
6m away from the coil carrier sheet
Coil ventilation kit (with 2.5, 4 and 6m
cable length)
The coil ventilation kit provides additional air cooling to the
coil carrier.
Control-unit with EMI
Control-unit which allow to connect the Modul Line system
to an Energy Management System (according to DIN 18875)
Control-unit with RS-458 Interface
Control-unit which allow to connect the Modul Line system
to an IoT or Connectivity solution.

16
Section 2
Installation
INSTALLATION SAFETY −DISCLAIMER
DANGER
Installation must be carried out by registered installation contractors only.
The contractors are responsible for interpreting all instructions correctly and performing the installation in
compliance with all applicable national and local regulations.
The warning signs and serial plates on the equipment must strictly be followed.
Warning
This equipment is intended for indoor use only. Do not install or operate this equipment in outdoor areas.
Warning
Before installation, make sure that the load capacity of the stove or counter is sufficient. It is important to
ensure that the ceramic glass is mounted flush with the stove top sheet. Lateral impacts on the ceramic glass
can quickly lead to a bursting of the ceramic glass.
Caution
Consultants, fabricators and designers must consult their induction suppliers when designing an appropriate
support structure and device clearance and the installation.
Notice
The Ceran® glass must be bonded using silicone that is compatible with foodstuff.
Notice
Induction equipment that is not installed correctly will have warranty voided.
INSTALLATION SAFETY—CLEARANCE AND VENTILATION
DANGER
Risk of Fire or Shock or Equipment Failure
All minimum clearances must be maintained. Air intake vents and exhaust vents must not be blocked or be
restricted.
Caution
This equipment must only be operated under an approved ventilation system in accordance with all
applicable national and local regulations. Exceptions may apply.
Notice
The maximum ambient temperature for the induction appliance to operate must not exceed 40 °C.
Failure to provide adequate ventilation will cause the appliance to overheat, to reduce power, or to
shutdown.
NOTE: Always maintain enough space between and around the equipment for maintenance and service.

17
Installation Section 2
INSTALLATION SAFETY—ELECTRICAL
DANGER
Installation must be carried out by registered installation contractors only.
The contractors are responsible for interpreting all instructions correctly and performing the installation in
compliance with all applicable national and local regulations.
The warning signs and serial plates on the equipment must strictly be followed.
DANGER
The device must be protected and connected with an all-pole circuit breaker which ensures complete
separation under overvoltage category III.
Warning
This equipment is intended for indoor use only. Do not install or operate this equipment in outdoor areas.
Warning
The device must be operated with an all-pole circuit breaker or disconnector of overvoltage category III.
Warning
CE Induction Appliance only: If ground fault current protective switches are used, they must be designed for
a minimum fault current of 30mA, Type B or B+.
Notice
Ensure the supply voltage and the line current match the specifications given on the serial plate affixed to the
appliance. Wrong voltage will damage the appliance. A stable power supply must be provided.
Notice
Always refer to the serial plate on the appliance to verify the electrical data. When the data listed on the serial
plate is different than that listed in this manual, contact the manufacturer or the authorized representative.
Notice
All cables must be routed, protected and tension free.

18
Installation Section 2
PERSONAL PROTECTION
DANGER
All utilities (gas, electric, water and steam) must be OFF to all equipment and locked out of operation according
to national/regional regulations, as well as company approved practices during installation, maintenance, and
servicing. Always allow appliance to cool.
DANGER
Use appropriate safety equipment during installation, maintenance, and servicing.
DANGER
Never stand, sit, or lean on the equipment!
They are not designed to hold the weight of an adult and may collapse or tip if misused in this manner.
DANGER
To avoid cardiac pacemaker malfunction, consult your physician or pacemaker manufacture about effects of
electromagnetic field on your pacemaker.
DANGER
Replace defective power cables immediately by an authorized service agency.
Warning
Markings and warning labels mounted directly on the equipment must be observed at all times and kept in a
fully legible condition.
Warning
Risk of burns from high temperatures. You may get burnt if you touch any of the parts during operation.
Surfaces close to the cooking area including side panels may get hot enough to burn skin. Use extreme caution
to avoid coming in contact with hot surfaces or hot grease. Wear personal protective equipment.
Caution
Use caution when handling the device. The device may have sharp metal edges.

19
Installation Section 2
Scope of delivery
The Modul Line is a modular induction system which is composed of interchangeable or optional components,
which can be ordered individually to ideally fit your built-in situation and application.
All Modul Line systems have crucial components. You need all of them to make the system work.
Interchangeable components are parts which replace a crucial component to match a specification which is
not part of the standard. Optional components are parts which are not required to run the system. You need
them to ease the built-in of the components or fulfill special specifications.
Crucial components
Generator
Potentiometer
Control-unit
Cable kit
Coil carrier
Interchangeable components
Operations Options (see General Information –Operations)
Cable kit 4 and 6m
Control-unit with EMI (see General Information –Further Option)
Control-unit with RS-485 (see General Information –Further Option)
Optional components
Ceran® glass
Mounting frame
Grease filter
Grease filter frame
Coil ventilation kit

20
Installation Section 2
Specifications - Dimensions
for the following Versions:
Modul Line 360 R 1x5 kW
Modul Line 360 R 2x3.5 kW
Modul Line 360 R 2x5 kW
Modul Line 360 R 4x3.5 kW
Modul Line 360 R 4x5 kW
The cut-out in the work top must be at least 368 x 368 mm for one coil carrier. The minimum available
depth for the coil carrier is 150 mm. The recommended distance between two coil carriers is 12 cm.
The required number of each component may vary according to the chosen version.
Dimensions are specified in mm [inches].
Coil carrier
Installation frame
Generator & Control-unit (please see specification Generator & Control-unit)