inergy APEX User manual

APEX USER MANUAL
#POWERFORLIFE

TABLE OF CONTENTS
1. Table of Contents (You Are Here)
2. Charging Your Apex
3. Using Your Apex
6. Apex Infographic
7. Apex Infographic Key & Specifications
8. Solar Energy General Guidelines
10. External Battery Guidelines
12. Connecting an External Battery
13. Safe Use & Storage Guidelines
15. Limited Warranty
1
FAQ
Q: How much does the Apex weigh?
A: The Apex weighs 25 pounds total.
Q: What type of AC Inverter is built into the Apex?
A: 1,500 Watt Continuous Pure Sine Wave, maximum starting surge of 3,000
Watts.
Q: What is the expected lifespan of the Apex battery?
A: Up to 2,000 cycles or 10 years if the battery is well maintained.
Q: What is the warranty for the Apex?
A: The warranty is one year limited.
Q: Is the internal lithium battery user replaceable?
A: No. Any battery service must be rendered by Inergy.
Q: How long will the battery hold its charge?
A: Up to a full year, however; we recommend checking the battery level every
3 months to ensure it is over 10% charged.
Q: Can I use the Apex while it is charging?
A: Yes. It’s capable of outputting power while charging.
Q: Can I fly on an airplane with the Apex, or ship it myself?
A: No. The Apex cannot be carried on or checked onto passenger aircraft.
Similarly, due to the size of the internal lithium battery, shipping the Apex
needs to be facilitated by a hazmat certified shipper ONLY.
Q: Can I connect lithium ion batteries to the Apex?
A: ONLY lithium batteries supplied by Inergy should be connected to the Apex.
Q: The LCD is still on, but I’m no longer getting power from the Apex -
why?
A: The Apex is equipped with resettable circuit breakers on the side of the
unit to prevent damage. In the event power output maximums are exceeded,
one of these breakers will pop and turn off that portion of the Apex. Simply
reset the breaker by allowing it to cool for several minutes, then push it back
into place. Reduce the power demand on the Apex, and you’re good to go!

CHARGING YOUR APEX
The Apex has two ports for charging. Only connect one
charge source at a time, connecting two simultaneously
will damage your Apex and may be dangerous.
•Port 1: Low current charge input for use with the included
Inergy Standard Wall Charger or Apex Car Charger ONLY.
DO NOT USE FOR SOLAR CHARGING. Both the Standard Wall
Charger and Apex Car Charger have a small LED light on the pow-
er supply that will turn red when the system is charging. Once
the light turns green, the system is fully charged. Another way
to verify the system is charging is by turning the Power Switch
to DC ONLY mode (see page 3 for more information). The LCD
should display CHG in the top middle to indicate the system is
charging, and the Wattage figure on the top right will display the
charge rate in Watts.
•Port 2: High current charge input for use with the Apex Quick
Wall charger and Inergy solar panels.
MAXIMUM INPUT: UP TO 500 WATTS, NOT TO EXCEED 26 VOLTS
DC (OPEN CIRCUIT, ABBREVIATED AS VOC) or 30 AMPS. When a
charge source is connected to Port 2, the blue charge indicator
LED will illuminate to indicate the system is charging. Another
way to verify the system is charging is by turning the Power
Switch to DC ONLY mode (see page 3 for more information). The
LCD should display CHG in the top middle to indicate the system
is charging, and the Wattage figure on the top right will display
the charge rate in Watts.
Charging with Solar Panel(s)
Charge times vary depending on solar panels used, sun condi-
tions, and angle of panel(s) relative to the sun. If using third
party panels not supplied by Inergy, always connect panels in a
PARALLEL wiring configuration - not a SERIES wiring configu-
ration. See PAGE 8 “Solar Energy General Guidelines.”
Charging with Standard or Quick Wall Charger
-The provided Standard Wall Charger is a 100 Watt charge source,
taking approximately 11 hours to fully recharge. Connect to Port 1.
-The Quick Wall Charger is a 189 Watt charge source, taking approxi-
mately 6 hours to fully recharge the Apex. Connect to Port 2.
Charging with Car Charger
Using a vehicle’s 12V DC socket charges the Apex at up to 113
Watts, taking approximately 10-11 hours to fully recharge. Con-
nect car charger to Port 1.
USING YOUR APEX
The Apex has a 3-position power switch that allows only specific
output ports to be activated based on your needs. The Apex can
be charged with the 3 position power switch in any position. See
the illustration and descriptions below for more information:
3
2
LEFT POSITION: All DC ports (12V DC sockets, Basecamp LED
Light ports, and the USB ports) on, otherwise referred to as DC
ONLY mode. This will also activate the LCD Display.
MIDDLE POSITION: All output ports off, otherwise referred to
as OFF mode.
RIGHT POSITION: All AC & DC ports on, otherwise referred to
as ALL ON mode. This will also activate the LCD display.

Powering Your Gear
Simply plug in your devices and turn on the power switch byfol-
lowing the guide above!
• Powering devices that consume very large amounts of elec-
tricity quickly (800 Watts or greater, like a refrigerator) can
deplete your battery capacity rapidly, and you may not get all
of the 1,100 Watt hours of energy stored in the Apex when fully
charged.
• When using large amounts of AC power at lower battery levels,
the inverter may turn off earlier than normal with useable bat-
tery capacity still available. Try reducing the amount of power
being used via AC. DC power may still be available, but more bat-
tery capacity is needed to power the inverter (AC outlets). Often
the last 10 - 20% of the battery is only available via DC.
• For safety, we have equipped the Apex with 3 resettable circuit
breakers on the side of the unit to prevent exceeding the maxi-
mum output rating for the various outputs. If the LCD remains
on, but power is no longer available from the Apex - it is possible
one of the circuit breakers opened. In the event power output
maximums are exceeded, one of these breakers will open by
popping outward, and turn off power output to the portion of the
Apex that was under stress. They are labeled as AC, DC 1, and DC
2. Simply reset the breaker by allowing it to cool for several min-
utes, then press it back into place. Reduce the power demand
on the Apex, and you’re good to go!
Reading the LCD Display
• The LCD Display is activated by the power switch in both DC
mode (DC ONLY) or AC/DC mode (ALL ON). A fully charged Apex
will be between 12.3 - 12.6 Volts. A completely discharged Apex
will be between 9.3 - 9.6 Volts. The LCD Display is used for deter-
mining battery capacity, how much power is being used (power
output), and how much power is coming into the Apex (charge
input).
NOTE: Very small power outputs (< 50 Watts) may not register
on the LCD on Section E, but remaining battery capacity percent-
age will be accurately reflected. See the illustration and descrip-
tions below for more information:
HOW TO READ THE LCD DISPLAY
54
Safety Mode
• Sometimes following transport, heavy use, or extended storage,
the Apex will go into Safety Mode. During Safety Mode, the Apex
will not turn on with the Power Switch. To take the system out
of Safety Mode, simply connect a charge source to either Charge
Input and leave it in for approximately 10 - 15 seconds. This
should restart the system. If the battery is depleted from long
term storage at a low battery level, the charge source may need
to remain connected for several minutes before the system will
turn on again.

7
APEX INFOGRAPHIC KEY
(A) Charge Port 1: Low current charge input for use with the included Iner-
gy Standard Wall Charger or Apex Car Charger ONLY. DO NOT USE FOR SOLAR
CHARGING.
(B) Charge Port 2: High current charge input for use with the Inergy Apex
Quick Wall charger and Inergy solar panels. MAXIMUM INPUT: UP TO 500
WATTS, NOT TO EXCEED 26 VOLTS DC (OPEN CIRCUIT VOLTAGE, ABBREVIATED
AS VOC) or 30 AMPS.
(C) External Battery Bank Connection: Battery posts for use with con-
necting external batteries. For use with Lead Acid, AGM, Gel Cell or INERGY
LITHIUM 12 Volt Batteries ONLY. NEVER CONNECT A CHARGE SOURCE TO ANY
CONNECTED EXTERNAL BATTERIES. See page 12 (External Battery Guidelines)
for more information. Connector Type: Ring Terminals.
(D) 110V AC Outlets: 1,000 Watts (10 Amps) maximum continuous output
per outlet. 1,500 Watts combined total output from all outlets, 3,000 Watt
starting surge maximum.
(E) RV Plug: Outlet for connecting to RV shore power cord. 1,500 Watt max-
imum continuous output (12.5 Amps), 3,000 Watt starting surge maximum.
Connector Type: Nema TT-30R.
(F) 12V DC Sockets: 180 Watts (15 Amps) maximum continuous output per
socket.
(G) USB Ports: USB-C PD: 5V 3A / 9V 2A / 12V 1.5A; USB-A QC 3.0: 5V 3A / 9V
2A / 12V 1.5A. NOTE: For full quick-charge or power delivery performance, the
Apex battery must be charged over 12 Volts.
(H) Basecamp LED Light Ports: 12V DC output. Connect up to 10 Base-
camp LED Lights chained together per port.
(I) Power Switch: 3 Position rotary switch: DC (DC ONLY MODE), ALL OFF,
AC/DC (ALL ON MODE)
(J) Carrying Handle & Shoulder Strap
(K) LCD Display: Turns on with power switch in either “on” position.
(L) High Current Charge Indicator Light: Illuminates when a high current
charge source is connected to Port 2 (see above).
Storing the Apex
•The Apex will retain a charge for up to a full year, but it is rec-
ommended that the battery level is checked every 3 months
to ensure it is not below 10%. Never leave in environments
exceeding 140˚F (like a hot vehicle), or in damp environments.
PRO TIP: Storing the Apex at half charge ensures the longest
battery life. See page 15 (Important Notice Regarding Lithium
Batteries) for more information about storing the Apex.
6
APEX INFOGRAPHIC

98
APEX SPECIFICATIONS
General Specifications
• Weight: 25 lbs (11.3 kg)
• Dimensions: 7” tall, 14” wide, 8” deep (17.78 x 35.56 x 20.32 cm)
• Operating Temperatures (Ambient):
-Charging Temperatures: 32°F - 104°F (0°C - 40°C)
-Discharging Temperatures: 20°F - 115°F (-6°C - 46°C)
•Charge Controller Type: MPPT
• Inverter: Pure Sine Wave - 1500 Watts Maximum Output, 3000
Watt Starting Surge
• Warranty: 12 Months
Battery Specifications
• Chemistry: Lithium NMC
• Capacity: 1,100 Wh (12.6V, 90 Ah), 550 Watts discharge contin-
uous for 2 hours
• Life Expectancy: Up to 2,000 Cycles to 80% Capacity
• Shelf Life: Up to 10 years - charge every 6 months, stored at
68°F (20°C).
• Management: Over-charge protection, over-discharge protec-
tion, short circuit protection, thermal protection, battery balanc-
ing.
SOLAR ENERGY: GENERAL GUIDELINES
Solar energy IS as simple as pointing panels at the sun. Howev-
er, there are many variables that CAN affect the panel’s perfor-
mance, and as such there are few hard and fast rules involved.
Our panels are rated at maximum output in IDEAL CONDITIONS.
On the nect page are a few of the most common variables that
affect performance, and some safety tips.
Ideal Time of Day
As a general rule of thumb, the brighter the sun is shining and
the clearer the day, the better solar panels will work. Panels op-
erate at peak efficiency when the sun is most direct – typically
around midday.
Solar panels run off of light, not heat. In fact, solar panels pro-
duce the most during cold, clear days rather than in extremely
hot conditions. Even during windy or rainy conditions, they are
able to function. While cloud cover will significantly reduce the
efficiency of the panels, they will still generate electricity.
Time of Year
The amount of daylight changes with the seasons. Summer
months offer the most day light hours. Because of this, overall
solar production is generally higher during those months.
While the winter months have fewer daylight hours, it is import-
ant to note that cold temperatures do not negatively affect the
panel’s performance. In fact, colder temperatures in clear condi-
tions can generate the most solar production overall.
Panel Angle
As a general rule of thumb, pointing your panel directly at the
sun will yield the best results. The angle will vary from month to
month and season to season. A panel angle of 30-60 degrees
from flat is generally considered the optimal angle, but as long
as you position your panels facing the sun, you will see results.
Tracking the sun throughout the day maximizes these results.

11
10
Unobstructed Sunlight
Solar panels function through the interaction of many individual
cells. Keeping this in mind, solar results can be greatly affected
with even the slightest obstruction to a single cell of the pan-
el. When selecting a location for panel placement, keep this in
mind. Make sure the panel is free of any debris, or any shadows
created by things like tree branches, overhead structures, or any
other objects in the environment.
Safety Tips
The Apex is designed for use with Inergy branded solar panels.
These solar panels will provide the best experience possible. As
a hard rule - all solar panels must be connected to the Apex (and
to each other) in a PARALLEL wiring configuration. Inergy solar
panels are designed in this way.
EXTERNAL BATTERY GUIDELINES
The Apex was designed with user customization in mind, in an
effort to expand the number of applications and versatility of
the system. External batteries are one of the main ways we have
done this. Below are some guidelines for expanding the power of
the Apex through additional batteries, as well as some import-
ant safety tips.
Connecting Batteries
Before external batteries are connected, they must be balanced
to match the Voltage of the Apex. Discharge the Apex to 10.5
Volts prior to connecting any external batteries. Similarly, ALL
EXTERNAL BATTERIES MUST BE WITHIN 0.1 VOLTS OF APEX
VOLTAGE (10.4 VOLTS - 10.6 VOLTS) BEFORE CONNECTING.
FAILURE TO DO SO VOIDS THE WARRANTY AND CAN RESULT
IN IRREPARABLE DAMAGE TO THE APEX AND/OR RISK OF
FIRE.
External batteries should be connected in a PARALLEL wiring
configuration to expand the battery capacity of the Apex (see
page 13 for more information). This is done by connecting
positive to positive, and negative to negative. This is the only
approved method for expanding battery capacity, any deviation
can result in severe damage to the Apex and create a potentially
dangerous situation. It will also void any and all warranties.
Battery wires & connectors: When connecting external
batteries to the Apex, we recommend using 2/0 Gauge battery
cables (made of pure copper, NOT copper plated) with 3/8” ring
terminals for up to a 5 foot long cable. Call our technical sup-
port for questions about longer lengths at [phone].
Number of Batteries
“How many batteries can I connect to the Apex?”
In general, we recommend connecting no more than 3,000 Watt
Hours (238 Ah, 12.6V) of external batteries for best results. Re-
member, the maximum charge input of the Apex remains steady
at 500 Watts. The more batteries that are connected, the lon-
ger they all take to charge.
Types of Batteries
“What types of batteries can I connect to the Apex?”
Any 12 Volt Deep Cycle Lead Acid, AGM, or Gel Cell battery can be
connected to the Apex. DO NOT connect external lithium batter-
ies not supplied by Inergy. Irreparable damage to the Apex or
fire could result.

CONNECTING EXTERNAL BATTERIES
12 13
SAFE USE AND STORAGE GUIDELINES
• NEVER connect solar panels or other charge sources exceeding
26 Volts (Open Circuit, abbreviated as VOC) to the Apex.
• NEVER connect solar panels in a SERIES wiring configuration.
All solar panels must be connected in a PARALLEL wiring config-
uration.
• NEVER store the Apex in environments exceeding 140 F, like a
hot vehicle.
• NEVER connect an external battery charger to any external
batteries that are connected to the Apex.
• NEVER connect any external battery to the Apex that is
charged higher than 12.6 Volts. We strongly recommend con-
necting external batteries charged to 10.5 Volts.
• NEVER connect an external battery that measures more than
0.1 Volts different than the Apex voltage at the time they are
connected. To illustrate, if your Apex is charged to 10.5 Volts at
the time you wish to connect an external battery, ensure the
external battery measures between 10.4 - 10.6 Volts before it is
connected. A Voltage meter (available at local hardware or auto
parts store) can be used to measure your external batteries.
IMPORTANT NOTICE REGARDING LITHIUM BATTERIES
In general, devices with large quantities of lithium ion batteries
(like the Apex) should be stored similar to a gas powered gen-
erator: away from flammable items and on a cool, dry, non-com-
bustible surface (like a garage or storage shed). When handling
lithium batteries, do not short-circuit, crush, drop, mutilate,
penetrate with foreign objects, apply reverse polarity, expose to
high temperature or disassemble packs and cells. If a Lithium
ion battery (or Apex) overheats, hisses, bulges, or pops, immedi-
ately move the device away from flammable materials and place
it on a non-combustible surface for at least 48 hours. If you
experience a lithium battery fire and the fire cannot be extin-
guished, allow the fire to burn out on its own in a controlled and
safe manner. It is possible for burning lithium- ion

15
14
***IMPORTANT SAFETY INFORMATION***
• NEVER connect an external battery charger to any external
batteries that are connected to the Apex. If connecting the
Apex to “house batteries” on an RV or Van, ensure those house
batteries are disconnected from any charge source in the vehi-
cle. Similarly, never attempt to charge external batteries that
are still connected to the Apex with a solar charge controller and
solar panels. ANY CONNECTED EXTERNAL BATTERIES MUST
BE MANAGED SOLELY BY THE APEX!
• NEVER connect any external battery to the Apex that is
charged higher than 12.6 Volts. We strongly recommend con-
necting external batteries charged to 10.5 Volts.
• NEVER connect an external battery that is more than 0.1 Volts
different than the Apex at the time they are connected. To
illustrate, if your Apex is charged to 10.5 Volts at the time you
wish to connect an external battery, any external battery must
measure between 10.4 - 10.6 Volts before they are connected. A
simple Voltage meter commonly available at local department
stores can be used to measure external batteries.
• NEVER connect external lithium batteries not supplied by Iner-
gy.
FAILURE TO FOLLOW THE ABOVE SAFETY TIPS MAY RESULT
IN PERMANENT DAMAGE TO YOUR APEX, RISK OF FIRE, OR
BODILY HARM. CALL OUR TECHNICAL SUPPORT TEAM IF YOU
HAVE ANY QUESTIONS AT [phone].
LIMITED WARRANTY
INERGY HOLDINGS (INERGY SOLAR) LLC warrants to the original
consumer purchaser that this INERGY SOLAR product will be
free from defects in workmanship and material under normal
consumer use during the applicable warranty period identified
in Paragraph 2, below, subject to the exclusions set forth in
Paragraph 6, below. This warranty statement sets forth INER-
GY SOLAR’s total and exclusive warranty obligation. We will not
assume, nor authorize any person to assume for us, any other
liability in connection with the sales of our products.
WARRANTY PERIOD
The warranty period for all INERGY SOLAR products and compo-
nents is one (1) year. In each case, the warranty period is mea-
sured starting on the date of purchase by the original consumer
purchaser. The sales receipt from the first consumer purchase,
or other reasonable documentary proof, is required in order to
establish the start date of the warranty period. Registration is
not required.
NO LEMON POLICY
INERGY SOLAR warrants to the original consumer purchaser that
should this INERGY SOLAR product require service (rendered
only by INERGY SOLAR) on (3) three separate occasions with-
in the above stated one (1) year warranty period, the unit can
be exchanged for a replacement product of comparable type,
quality, and functionality at the request of the original consumer
purchaser. Validation by an INERGY SOLAR technician of product
failure is required prior to replacement. Your warranty remains in
force for the duration of the original one (1) year warranty period,
and is in no way terminated by replacement product under this
No Lemon Policy.
batteries to reignite after being extinguished, so allow the
device to remain on a non-combustible surface for at least 48
hours.
If you have any questions about your Apex or the above instruc-
tions, please call us at [phone].

880 N 5th Ave, Pocatello, ID 83201
[e-mail]
[phone]
#POWERFORLIFE