Infiniti Direct X9 Series User manual

11
Check List IF ANY OF THESE PARTS ARE MISSING CONTACT YOUR DEALER IMMEDIATELY.
Introduction
Check List
Care and Maintenance
Assembly Steps 1~5
Assembly Steps 6~9
Detailed Parts List
Exploded Drawing
page 1
page 1
page 1
page 2
page 3
page 4
page 5
Congratulations on your purchase of the ELLIPTICAL
CROSS TRAINER. This product has been designed
and manufactured to meet the needs and requirements
of domestic use.
Please carefully read the instructions prior to assembly
and first use. Be sure to keep the instructions for
reference and/or maintenance.
If you have any further questions, please contact us.
We wish you lots of success and fun while training.
Introduction Table of Contents Care and Maintenance
Your ELLIPTICAL CROSS TRAINER is made of the
highest quality materials, even so it is still important
that you take care of your ELLIPTICAL CROSS
TRAINER on a regular basis. Your ELLIPTICAL
CROSS TRAINER is for indoor use only and should
NOT be used or stored in damp areas. Wipe all
perspiration from your ELLIPTICAL CROSS TRAINER
after each use.
The safety level of your ELLIPTICAL CROSSTRAINER
can only be maintained if it is examined regularly for
damage and wear. As a sensible precaution quickly
visually safety check and clean before use. We
suggest a more thorough inspection every two to three
weeks. If any defects are found discontinue use
immediately and contact your dealer for advice on how
to proceed.
Components most Susceptible to Wear
DUALACTION HANDLE [part# 201,306,401]
STATIONARY HANDLE BAR [part# 302]
STABILIZER - FRONT and REAR [part# 202,308,403]
FOOT PEDAL [part# 116]
These parts are assembled by the consumer and
should be checked regularly. Make sure that all Nuts,
Bolts and Knobs are tight and secure.
All FASTENERS [Nuts, Bolts, and Screws]
All fasteners that are easily accessible should be
tightened on a regular basis.
The 3x Pivot Points
[part#17,22,24,27,30,32,36,62]
The 3x Pivot Points combine BEARINGS with
BUSHINGS. The BEARINGS should last a
lifetime with normal use. The BUSHINGS are a
special design incorporating a space age plastic
with lubricate built inside. As well they are
greased by the manufacturer and should last a
lifetime with normal use.
WARNING: Do NOT apply oil to any moving parts
as this will wash the grease away damaging the
ELLIPTICALCROSS TRAINER.
If you want to replace the BEARINGS then do so
with care. If you wish to grease the BUSHINGS
use a good quality grease that is friendly to
plastic (some greases destroys plastic).
To replace the BEARINGS and grease the
BUSHINGS disconnect the FOOT PEDAL TUBE
[011&012]andtheDUALACTIONARM[005&006].
Replace the BEARINGS and grease the
BUSHINGS.Thenreassemble.
M13
M14
M5
ASSEMBLY INSTRUCTIONS

2
STEP1
Clear a 2 x Meter by 2.5 Meter working space before
unpacking your ELLIPTICALCROSS TRAINER.
STEP2
a) Use a sharp knife, open the carton and lay it flat
on the floor.
b) Remove all loose components.
c) Refer to the checklist and check that everything is
present.
NOTE: To protect the ELLIPTICAL CROSS TRAINER
while assembling we suggest that you do not remove
the Protective Packing Material until it is absolutely
necessary.
STEP3
a) Lift the rear of the machine off the floor and slide
a Polystyrene Block under the rear-end of the
machine.
b) Assemble the REAR STABILIZER [003] with 2 x
BOLT [308] + 2 x WASHER [403] + 2 x NUT [202]
and tighten firmly.
308
403
003
STEP4
a) Remove all Polystyrene Blocks.
b) With another person helping you carefully lift the
UPRIGHT TUBE [004] until it is vertical while the
other person joins the plugs of the COMPUTER
CABLE [703] to MOTOR with CABLE [701] as
shown in the illustration below. Then slide the
UPRIGHTTUBE[004]intotheMAINFRAME[001].
c) Looselyassembly6xBOLT[302]+WASHER[401]
intoMAIN FRAME[001]. Rotatethe FOOTPEDAL
TUBES [011 & 012] at least two times to correctly
align the UPRIGHT TUBE [004] then firmly tighten
6xBOLT[302].
d) Slide down the HAT COVER [111] and push firmly.
701
703
302
401
1
004
STEP5
a) Assemble the FRONT STABILIZER [002] with
2xBOLT[308]+2xWASHER[403]+2xNUT[202]
andtightenfirmly.
b) Remove2xBOLT[300]fromUPRIGHTTUBE[004].
Align WATER BOTTLE HOLDER [135] and fasten
withthesame2xBOLT[300].
ASSEMBLY INSTRUCTIONS
300
135
308
002
202
403
004
202

STEP8
a) Insert the LEFT DUAL ACTION HANDLE [007]
into the top of the LEFT DUALACTIONARM [005]
Note Left Sticker.
b) Insert the RIGHT DUAL ACTION HANDLE [008]
intothetopoftheRIGHTDUALACTIONARM[006]
Note Right Sticker.
c) Securewith4xBOLT[306]+4xWASHER[401] + 4 x
NUT[201]andtightenfirmlybutDONOTovertighten.
STEP9
a) Connect the to the COMPUTER [710].
b) Feed the excess cables into the hole in the
STATIONARY HANDLE BAR [013].
COMPUTER CABLE [703] + HAND
PULSE CABLE [704]
c) On the top of the STATIONARY HANDLE BAR
[013] is the Computer Plate. Position the
COMPUTER [710] on the Computer Plate and
secure with 4 x BOLTS [310].
13
STEP7
a) Slide the ADJUSTABLE FOOT PEDAL [115] onto
the left and right FOOT PEDAL TUBE [011 & 012].
Secure with ADJUSTABLE FOOT PEDAL KNOB
[116] and tighten firmly.
NOTE: The ADJUSTABLE FOOT PEDAL [115] can be
adjusted to your personal preference, but we suggest
that you start with the middle setting number 3.
STEP6
a) Feed both the COMPUTER CABLE [703] + HAND
PULSE CABLE [704] out through the top of the
STATIONARY HANDLE BAR [013] then slide the
STATIONARY HANDLE BAR [013] into the
UPRIGHT TUBE [004].
b) Secure with 3 x BOLT [302] + 3 x WASHER [401].
Before tightening make sure the STATIONARY
HANDLEBAR[013]correctlypositioned.
008
007
005
006
201 306
401
013
004
115012
116
011
ASSEMBLY INSTRUCTIONS
704
703
302 401
115
310
013 703
704
710

4
DESCRIPTION Q’TY
PART
No. DESCRIPTION Q’TY
PART
No. DESCRIPTION Q’TY
PART
No.
X9 Series Elliptical Cross Trainer
April 2006
DETAILED PARTS LIST
MAIN FRAME
STABILIZER - FRONT
STABILIZER - REAR
UPRIGHT TUBE
DUALACTION ARM - LEFT
DUALACTION ARM - RIGHT
DUALACTION HANDLE - LEFT
DUALACTION HANDLE - RIGHT
DISC COVER FRAME - LEFT
DISC COVER FRAME - RIGHT
FOOT PEDAL TUBE - LEFT
FOOT PEDAL TUBE - RIGHT
STATIONARY HANDLE BAR
ANGLE ADJUSTMENT TUBE
FRONT PIVOT SHAFT
TENSION WHEELARM
TENSION WHEEL SPACER
PANCAKE SLIDER
PANCAKE SLIDER WHEEL
PANCAKE CABLE GUIDE
DISC COVER - LEFT
DISC COVER - RIGHT
DISC COVER PLUG
FRONT COVER - LEFT
FRONT COVER - RIGHT
REAR COVER - LEFT
REAR COVER - RIGHT
MIDDLE COVER
HAT COVER
FOOT PLUG with WHEEL
HEIGHT ADJUSTER CAP
HEIGHT ADJUSTER FOOT
ADJUSTABLE FOOT PEDAL
ADJUSTABLE FOOT PEDAL KNOB
TENSION WHEEL
BUSHING - BEARING
BUSHING - STANDARD
UPRIGHT TUBE SPACER
DUALACTION ARM KNOB
PLUG
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
119
120
121
122
123
124
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
3
1
1
2
1
1
1
1
1
1
2
2
2
2
4
1
4
6
2
2
2
NUT COVER
PLUG
FOAM GRIP
FOAM GRIP
BUSHING - CUP
PANCAKE ALUMINUM
PANCAKE SLEEVE
HUTCHINSON BELT
WATER BOTTLE
WATER BOTTLE HOLDER
FLYWHEEL with MAGNETS
ANGLE ADJUSTMENT SLEEVE
ANGLE ADJUSTMENT KNOB
PLUG
NUT
NUT
NUT
NUT
NUT
NUT
NUT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
BOLT
WASHER
WASHER
WASHER
WASHER
WASHER
WASHER
WASHER
WASHER
125
126
127
128
129
130
131
133
134
135
136
137
138
139
200
201
202
203
204
205
206
300
301
302
303
304
305
306
307
308
309
310
400
401
402
403
404
405
406
407
6
2
2
2
4
1
2
1
1
1
1
2
2
2
6
4
4
1
1
1
1
2
1
9
1
1
1
4
2
4
1
4
1
13
6
4
1
1
1
1
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
MOTOR TENSION CABLE
MOTOR with CABLE
SENSOR with CABLE
COMPUTER CABLE
HAND PULSE CABLE
HAND PULSE SENSOR
PANCAKE SLIDER CABLE
PANCAKE FLYWHEEL SHAFT
PANCAKE SPRING
SENSOR MAGNET
COMPUTER
D/C ADAPTOR SOCKET with CABLE
A/CADAPTOR
BEARING
BEARING
BEARING
500
501
502
503
504
505
506
507
508
700
701
702
703
704
705
706
707
708
709
710
711
712
800
801
802
1
14
3
3
2
12
4
2
4
1
1
1
1
1
4
1
1
1
1
1
1
1
3
3
4

15
EXPLODED DRAWING
X9 Series Elliptical Cross Trainer
April 2006