Infiniton CMPP-RU92 User manual

DECORATIVE CHIMNEY HOOD
CAMPANA EXTRACTORA DECORATIVO
User Manual ES
GB
Manual De Instrucciones
H10-20-300-048 Rev 002

2
Dear Customer,
Thank you very much for your preference for products. Our objective is to
ensure that you enjoy this product, manufactured environmentally-friendly
with a total sense of quality in a precise working environment at our modern
facilities, most efciently.
We recommend you to read the instruction manual carefully and keep
it handy before you use this chimney hood so that it maintains its quality
just like the rst day you bought it and serves you most efciently.
NOTE:
This Instruction Manual has been prepared for a variety of models.
Some of the features specied in the Manual may not exist in your device.
These features are marked with *.
Our devices are designed for domestic use. They are not for professional
use.
“PLEASE READ THE INSTRUCTIONS BEFORE YOU INSTALL OR USE THIS
DEVICE.”
This product has been manufactured in an environmentally-friendly
and modern plants without harming the nature.
“Conforms with the AEEE Regulations.”
GB

3
CONTENTS
1. Safety Instructions 4
2. Introduction And Technical Drawing
Of The Chimney Hood 7
3. Installation Of Chimney Hood 8
3.1. Location Of The Chimney Hood 8
3.2. Mounting Chimney Hood On The Wall 8
3.3. Mounting The Aluminum Pipe 8
3.4. Installation Of Outer Duct 9
3.5. Installation of Inner Duct Mounting Bracket 9
4. Functions Of The Chimney Hood 9
4.1. Control Panel 9
4.2. Symbols Functions 9
5. Operating The Chimney Hood 10
5.1. In Ducted Use 10
5.2. Round Charcoal Filter 10
5.3. Use Of Charcoal Filter 11
5.4. Installation Of Charcoal Filter 11
5.5. Use Of Aluminum Cartridge Filter 11
6. Replacing The Bulb 11
7. Maintenance Of The Chimney Hood 12
8. If Chimney Hood Does Not Work 13
9. Environmentally-Friendly Disposal 14
10. Package Information 14
GB

4
1. SAFETY INSTRUCTIONS
1.This product is designed for domestic use.
2.Product Voltage is 220-240 Volts 50Hz.
3.Power cord of your product is tted with grounded
plug. This cord must be plugged into a grounding socket.
4.All electrical installation must be done by a qualied
electrician.
5.Installation by unqualied persons may lead the
product run with lower performance, be damaged or
cause accidents.
6.Power supply cord should not be jammed or crushed.
Power cord should not be close to hobs, etc, otherwise
it may melt and cause re.
7.Do not plug in the product into a socket before the
installation is complete.
8.Make sure the mains switch is easily accessible in
order to cut the power of the product in case of any
danger.
9.Do not touch the bulbs of your product if used for a
long period of time. The bulbs will be hot and may burn
your hand.
10.Kitchen chimneys are designed for domestic use.
If used for other purposes, it may lead to a failure and
not be covered under the warranty.
11.Follow the authorized agencies’ rules and regula-
tions regarding letting out the air. (This warning does
not apply to usage with non-ducted chimney hoods.)
GB

5
12.Food that may burst into ames should not be
cooked under the device.
13.Turn on the product after you place pots, pans, etc on
the hobs. Otherwise excess heat may cause deformation
of some parts of your product.
14.Do not leave hot oil on the hobs. Pans with hot oil
inside may cause self-ignition.
15.When cooking i.e. deep frying, hot oil may burst
into ames. Be careful on your curtains and cloths.
16.Make sure you replace the lters at the recom-
mended intervals. Filters not replaced on time carry
re risk due to increase of grease on them.
17.Do not use non-re-resistant materials instead of
lters.
18.Keep the potentially dangerous packaging materials
away from children.
19.Do not use your product without a lter, do not
remove lters when the product is operating.
20.In case of start of ames, cut off the power of the
chimney fan and cooker.(Cut off the power by unplugging
the device).
21.Turn off the hobs before you remove pots, pans,
etc.
22.If the cleaning is not done periodically, your product
may carry re risk.
23.Cut off the power supply before any maintenance
work. (Cut off the power by unplugging the device.)
GB

6
GB
24.For duct-out chimney hoods, use pipes with a di-
ameter of 150 mm or 120 mm. You should minimize
the ducting distance with minimum bends.
25.Make sure your children do not play with the
product. Do not let young children operate the product.
26.If the power cord is damaged, the damaged cord
should be replaced by the manufacturer or its service
agent or similarly specialized personnel in order to
avoid a dangerous situation.
27.In case of start of ames, cut off the power of the
chimney fan and cooker and cover the ame. Do not
use water to extinguish the re.
28.WARNING: Install “MAX. 6 A” fuse for the extractor
fan.

7
2. INTRODUCTION AND TECHNICAL DRAWING OF THE CHIMNEY HOOD
E
F
1. Duct
2. Control panel
3. Filter
4. Lighting
A170 mm
B200 mm
C700 mm
D25 mm
E450 mm
F596 mm / 896 mm
1
2
3
4
AB
C
D
GB

8
3. INSTALLATION OF CHIMNEY HOOD
3.1. Location Of The Chimney Hood
3.2. Mounting Chimney Hood On The Wall
2 drywall (8mm) anchors are nailed into the holes drilled according to
installation template (A,B). They are xed into the wall through 2 key
holes by screws as shown in Figure 1.
3.3. Mounting The Aluminum Pipe
Place the aluminum pipe on the plastic duct. Place the other end of the
pipe into the air outlet in the kitchen. (Figure 2)
Twists and bends on the aluminum pipe may cause minimizing the air suction
so avoid unnecessary bends and twists as much as possible. (Figure 3-4)
Place the inner duct and outer duct carefully on the product.
0
80
50
130
220
180
250
MAX
90
80
70
40
30
10
20
50
0
60
Min. 650 mm.
Figure 1
Installation Template
A B
GB

9
Fix the inner duct to inner duct connection plate with 2 screws.
3.4. Installation Of Outer Duct
Put the outer duct on the chimney hood and x to it by 2 screws (Figure 5)
3.5. Installation of Inner Duct Mounting Bracket
2 xing holes are drilled on the wall with Ø 6 mm electric drill at a suitable
height and place to x the inner duct hanger plate onto the wall. 6mm
drywall anchors are nailed into those holes and inner duct mounting
brackrets are pinned down. (Figure 6)
At the last step of chimney hood installation, the inner duct is screwed
on the inner duct mounting brackets.
Note: Packaging may not include inner duct according to model.
4. FUNCTIONS OF THE CHIMNEY HOOD
4.1. Control Panel
Digital Control: Touch the symbols on
the keys. (On/Off function and timer
are on the same key; if pressed for 1
sec on-off function will operate.
If pressed for 3 sec. 15 minutes timer will operate.
Figure 3 Figure 4
Figure 2
Figure 5 Figure 6
GB

10
4.2. Symbols Functions
Note: When the product operates for a certain time, the aluminum lters
get dirty and the digital display shows “C” Clean sign. This means the l-
ters should be cleaned. Press the speed reduction key for 5 secs in order
to delete “C” sign from the display.
Push Buton: Pressing the buttons will enable different functions. In order
to disable them, press only the button Off.
5. OPERATING THE CHIMNEY HOOD
Chimney hood is used in ducted and non-ducted kitchens.
5.1. In Ducted Use
In ducted use, extractor fan should be connected to an air outlet to
send the air out. In order to use your chimney hood efciently, make sure
length of the pipe system between the chimney hood and the air outlet
should be short. Your product has been manufactured suitable for ducted
and non-ducted use.
5.2. Round Charcoal Filter
In kitchens with no duct, a round charcoal lter should be reintroduced
the clean air into the kitchen. You can obtain the round lter from your
service or dealer.
Switches on and off the motor.
(Except for the lighting)
Increases the speed when the motor
is running.
Decreases the speed when the motor
is running.
If pressed this symbol, the motor
turns itself off 15 minutes later.
Display Only switches on and off the lighting
system.
OFF MIN MID MAX
Medium speed
Stops the motor, except for the ligh Intense speed
Low speed It turns on and off the lighting
system only.
OFF
MIN
MID
MAX
GB

11
5.3. Use Of Charcoal Filter
• Our products allow the installation of charcoal lter.
• Regardless of use of charcoal lters or not, grease lters should be
installed on the product. Do not use your product without grease
lter.
• Use of charcoal lteris as follows.
• Cut off the device power before replacing charcoal lter.
• Charcoal lter is used in the kitchens with no duct therefore should
be replaced in every 3-5 months depending on the frequency of use.
• Charcoal lter should never be washed.
5.4. Installation Of Charcoal Filter
• Charcoal lters are used in the kitchens with no duct.
• Charcoal lters are installed onto both sides of the fan as shown
in Figure 7 by turning 10 degrees clock-wise.
• When uninstalling, reverse the same procedure.
5.5. Use Of Aluminum Cartridge Filter
Aluminum cartridge lter holds dust and grease in the air. Chimney
hoodshould never be used without aluminum cartridge lter. (Figure 8)
6. REPLACING THE BULB
Always switch off the electrical supply before carrying out any operation.
6.1. Led
• LED bulb does not operate is possible to remove as shown in Figure 9
• A new bulb to be supplied from service points is replaced with the
same reoperation.
• Cables are designed with sockets. The plug in should be made according
to previous connection.
Installing Position
Figure 7 Figure 8
GB

12
GB
6.2. Candle Type Halogen Bulb
• Bulb does not operate is possible to remove as shown in. (Figure 9)
• A new bulb with the same features is replaced with removed bulb.
• Remove the holder on the LED bulb. Put the new LED bulb on the
holder housing of the LED bulb you removed as shown in Figure 10.
7. MAINTENANCE OF THE CHIMNEY HOOD
• Device should be unplugged or switch should be turned off before
cleaning and maintenance procedures.
• Metal lter should be cleaned once a month with hot soapy water or
in the dishwasher, if possible. (60 °C)
• Remove the aluminum cartridge lter by pressing on the spring
catches on the side. Do not ret before drying after wash.
• Outer surface of the extractor hood should be wiped with a damp
cloth soaked with soapy water.
• Make sure electronic parts do not contact with water or similar materials.
• For inox products, using inox cleaning and maintenance products
available in the market will provide longer usage life for your device.
• Aluminum lters can be washed in dishwasher. After several washes,
aluminum lters may change colour. This is normal and lters do not
need to be replaced.
WARNING: When used with devices which use fuel (heaters working with
gas, diesel fuel, coal or rewood, water heaters, etc) and the air in the
environment; should be used cautiously. The chimney hood sending the
air out in the environment may affect the burning adversely.
This warning is not applicable to non-ducted use.
Figure 10
Red
Black
Figure 9

13
GB
Efficient Use Of Chimney Hood;
• When installing the chimney hood to the air duct, use 150/120
mm diameter pipes and use bends as minimum as possible.
• Be ware of cleaning periods of metal lters and replacing times
of charcoal lters.
• When dense suction power is not required, use the product in
medium setting.
• For right ventilation, the windows in the kitchen leading to the
outside should be kept closed.
8. IF CHIMNEY HOOD DOES NOT WORK;
Before contacting the service, make sure the product is plugged and
the fuse in the electrical installation is working. Do not do anything that
may harm the product.
Service And Spare Parts
Have one of our authorized services install your device free of charge.
You can supply spare parts of your device from your dealer or authorized
services. The package includes a list of authorized services with the product.
When you contact your service or dealer to ask for any spare parts,
notify them of product model name shown in the product label. When
you remove the aluminum cartridge lter, you will see the product label.
Before contacting your service, check your chimney hood against the
table below. If problem persists, contact your dealer or authorized service
point.

14
GB
9. ENVIRONMENTALLY-FRIENDLY DISPOSAL
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with European
Directive 2012/19/EU concerning used electrical and
electronic appliances (waste electrical and electronic
equipment - WEEE). The guideline determines the frame
work for the return and recycling of used appliances as
applicable throughout to the EU.
10. PACKAGE INFORMATION
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations.
Do not dispose of the packaging materials together with the domestic
or other wastes. Take them to the packaging material collection points
designated by the local authorities.
Chimney Hood
does not work
Light bulb is
not working
Chimney hood air
suction is poor
Do not send air out
(in non-ducted cases)
Check electricity connection (mains voltage should be 220-240 V, Chimney hood should be connected to grounding socket.) Check motor switch (Motor switch should be on.) Check bulb switch (Bulb switch should be on.) Check bulbs (Bulbs should be in working condition.) Check aluminum filter (Aluminum cartridge filter should be washed once a month in normal use.) Check air outlet shaft (Air outlet shaft should be unblocked.) Check charcoal filter (Charcoal filters should be replaced quarterly in normal use.

15
Estimado Cliente,
Antes de todo, agradecemos para comprar productos de. Nuestro objetivo
es obtener su uso con desempeño máximo de este producto que ha sido
producido según el principio de cualidad total en nuestros plantas mod-
ernas, sin dañar el ambiente.
Para que la campana extractora de que vd. ha comprado sirva son sus
rasgos de primer día y en el desempeño máximo por favor lea este manual
antes de usarlo y lo guarde para siempre.
NOTA:
Este manual es preparado para modelos diferentes. Algunos rasgos
que son especicados en este manual no podría ser en su aparato.
Estos rasgos son marcados con la marca *.
Nuestros aparatos tienen el objetivo de usar en la casa. No son producidos
a usar con objetivos comerciales.
“ POR FAVOR LEA LOS INSTRUCCIONES ANTES DE MONTAR O USAR ESTE
APARATO.”
Este producto es manufacturado en plantas modernas sin dañar el a
biente natural.
“Conveniente al Reglamento de AEEE”
ES

16
ÍNDICE
1. Instrucciones De Seguridad 17
2. Introduccion De Campana Extractora
Y Diseño Técnico 20
3. Montaje De Campana Extractora 21
3.1. La Posición De La Campana Extractora 21
3.2. Montaje De Campana A La Pared 21
3.3. Montaje De Manguera De Aluminio 21
3.4. Inserción Del Eje Exterior 22
3.5. Montaje De Placa De Gancho
De La Chimenea Interior 22
4. Funciones De Campana Extractora 23
4.1. El Panel De Control Y Sus Funciones 23
4.2. Símbolo Funciones 23
5. El Uso De La Campana Extractora 23
5.1. En El Uso Con Chimenea 23
5.2. Filtro Redondo De Carbón 24
5.3. Uso De Filtro De Carbón 24
5.4. Montaje De Filtro De Carbón 24
5.5. Uso De Filtro Cartucho De Aluminio 24
6. Cambio De Lámpara 24
7. Mantenimiento Y Limpieza De La Campana 25
8. Si La Campana No Funciona 26
9. Eliminación Respetuosa Con El Medio Ambiente 27
10. Información De Embalaje 27
ES

17
1. INSTRUCCIONES DE SEGURIDAD
1.Este producto es diseñado para uso doméstico.
2.El voltaje del producto es 220-240 V y 50Hz.
3.El producto debe conectarse mediante un cable
a la toma de tierra.
4.Toda la instalación eléctrica debe ser realizada
por un técnico cualicado.
5.Una instalación realizada por personas no cualicadas
puede provocar daños al producto, accidentes o un
funcionamiento ineciente.
6.Debe asegurarse de que el cable de alimentación
no esté apretado o comprimido. No deje el cable de
alimentación cerca de otros objetos calientes como
estufas o fuegos, ya que podría derretirse y causar
fuego.
7.No ponga el clavija en el enchufe antes del montaje
del producto.
8.Asegurese de que la clavija de anclaje y el enchufe
son de fácil acceso para poder cortar la electricidad
en caso de emergencia.
9.Si su producto ha estado en funcionamiento
durante un largo tiempo, no toque las lámparas ya
que podría quemarse.
10.Las campanas extractoras son para uso exclusiva-
mente doméstico. Si se usa para otros nes hay riesgo
de defecto y la garantía queda anulada.
ES

18
11.No cocine productos inamables debajo de este
aparato.
12.Instale este producto antes de cocinar. El calor de
los fuegos podría dañar algunas partes de su campana.
13.Apague los fuegos antes de retirar las cacerolas,
ollas, etc para evitar quemaduras.
14.No deje aceite caliente sobre la estufa. Los recipi-
entes con aceite podrían inamarse espontáneamente.
15.Cuando cocine fritos tenga cuidado, los aceites
pueden inamarse y causar quemaduras personales o
materiales.
16.Se recomienda sustituir los ltros en el tiempo no-
ticado por el fabricante. Sino se cambian los ltros en
el tiempo recomendable existe riesgo de inamación por
el aceite que se acumula en elllos.
17.No use elementos sustitutos para el ltro, ya que
podrían ser inamables.
18.Los elementos de embalaje son peligrosos para
los niños. Guárdelos fuera del alcance de los niños.
19.No ponga en funcionamiento el aparato sin ltro y
no quite los ltros mientras el aparato está encendido.
20.En caso de inamación: corte la energía eléctrica
del aparato y de otros aparatos cercano. Desconecte el
enchufe. Tape los fuegos con una tela húmeda o una
toalla mojada pero nunca use agua para extinguir el
fuego.
21.La limpieza del aparato debe ser periódica para
evitar riesgo de fuego.
ES

19
22.Corte la energía del aparato antes de mantenimiento.
(Corte la energía del aparato tirando el clavija del
enchufe.)
23.Cuando instala la tubería de extracción a la chime-
nea debe usar un tubo de 150mm o 120mm. La conex-
ión tiene que ser lo más corta posible, sin pliegues y con
pocas curvas.
24.Asegúrese que los niños no juegan con este
producto.No deje que los niños usen el aparato.
25.Si el cable de alimentación está dañado debe
ser sustituido por personal cualicado para evitar
situaciones peligrosas.
26.Para su seguridad use fusibles de plomo “Máximo
6A” en la instalación de su campana extractora.
ES

20
2. INTRODUCCION DE CAMPANA EXTRACTORA Y DISEÑO TÉCNICO
E
F
1. Chimenea
2. Panel de control
3. Filtro
4. Iluminación
A170 mm
B200 mm
C700 mm
D25 mm
E450 mm
F596 mm / 896 mm
1
2
3
4
AB
C
D
ES