Infinity FPS-1000 User manual

Technical Manual
FPS-1000
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance 6 ohms
• Max Amp Power 75 watts
• Frequency Response 75Hz - 20kHz
• Sensitivity 88 dB (1 watt @ 1 meter)
• Crossover Frequency 3800 Hz
SYSTEM COMPONENTS:
• Enclosure FPS-1000 (Not for Sale)
• Grille 196851
• Low Frequency Transducer 5¹⁄₄” Low-profile Woofer
(310143)
DC Resistance 3.1 ohms ±10%
• High Frequency Transducer 1” (25mm) Soft Dome
Rotatable (310144)
DC Resistance 3.7 ohms ±10%
• Passive Radiator 196849
• Crossover Network 197317
AURAL SWEEP TEST SPECIFICATIONS:
• System Aural Sweep Test 6.0V Input 75 Hz to 20 kHz
• L.F. Aural Sweep Test 6.0V Input 75 Hz to 4 kHz
• H.F. Aural Sweep Test 2.0V Input 3 kHz to 20 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure dimensions: 25¹⁄₄ x 11¹⁄₂ x 1¹⁄₂” (H x W x D)
641 x 292 x 38 mm
• Weight 26 lbs. (11.8kg) Sold in Pairs
WARRANTY:
• Refer to Warranty Statement packed with each product.
Plastic Bag
Outer carton
196902
Foam End Pads (2)
42191
Owner's Manual
197287
Warranty Card
333715-001
Survey Card
330033-001
OWNER'S
MANUAL
Flat Wire (40')
197174
Allen Hex Key
197228
PACKAGING WIRING DIAGRAM
7-99
Infinity Systems, Inc. 250 Crossways Park Dr., Woodbury, New York 11797
FPS-1000
Ð +
RED
BLK
RED
BLK
Ð +
Driver High
Frequency
310144
Driver Low
Frequency
310143
Crossover
Network
197317
L2
0.35 mH
L1
0.17 mH
C1
4.7 mfd, 100V
C2
22 mfd
100V
PL1 R1
2.7 , 5W +
+
+205
110
205
110
H.F.
L.F.
RED
BLACK
RED
BLACK
INPUT
FPS-1000 SCHEMATIC

Grille
196851
Logo
197102
Grille Gasket
197169
Tweeter
310144
Screws (33)
³⁄₈" Black FHD
Enclosure
FPS-1000
(Not for Sale)
Woofer
310143
Screws (4)
⁵⁄₁₆" FHD
Network
197317
Passive Radiator
196849
Screws (8)
⁷⁄₃₂" Plated
Screws (8)
⁷⁄₃₂" Plated
Back Panel
(Not for Sale)
Screws (4)
10mm white
FPS-1000
FPS-1000
7-99
Infinity Systems, Inc. 250 Crossways Park Dr., Woodbury, New York 11797
EXPLODED VIEW
SERVICE NOTE
To adjust direction of rotatable tweeter:
1. Remove the (4) 10mm white Grille screws (Use the 2mm
hex key supplied in the hardware).
2. Remove the grille
3. Depress the outer edge of the tweeter with your finger to
rotate it to the desired position.
4. Replace the grille.
To access the drivers or network:
1. Lay the loudspeaker face down on a padded surface.
2. Remove all (33) ³⁄₈” Black flat head screws from the back panel.
3. Lift the back panel up and off the enclosure.
4. Lift the Dacron filler carefully up and out of the enclosure,
taking care not to dislodge gaskets or wires.
Tweeter removal:
1. Follow steps 1-4 above. (To access the drivers or network)
2. Locate the 3-lobed retainer at the rear of the tweeter; dis
lodge the prongs from the sealant and rotate the retainer
CCW until free of the plastic cup.
3. Pull the tweeter up and out of the enclosure.