Inflatable Marine Products Wolf Cub User manual

1
Inflatable Marine Products Inc.
OWNERS MANUAL
Wolf Cub/Predator/Survivor
Your SeaWolf Inflatable is a “performance watercraft”.
Please use caution when running this craft. Be sure to respect
all water safety laws for your state or country AS WELL AS
THE RESPECT FOR FELLOW BOATERS, SWIMMERS
AND ALL WATER ACTIVITIES .
You must remain seated at all times while this craft is in
motion.
Stay clear of the outboard and spinning propeller.

2
Table of contents
Page
3 Getting started
4 Parts list
5 Assembly
7 Maintenance (Care of your SeaWolf Inflatable)
8 Registering, Your Inflatable
(FOR WATER USE IN YOUR STATE)
9 Specification
10 Technical Support

3
Getting Started
CAUTION!
Your SeaWolf Inflatable is a “performance watercraft”.
Please use caution when running this craft. Be sure to respect
all water safety laws for your state or country AS WELL AS
THE RESPECT FOR FELLOW BOATERS, SWIMMERS
AND ALL WATER ACTIVITIES.
You must remain seated at all times while this craft is in
motion.
Stay clear of the outboard and spinning propeller. Never enter
or exit your boat from the rear!
BE A SAFE BOATER AND STAY ALIVE!
PARTS LIST

4
SeaWolf Inflatable Standard Equipment.
Wolf Cub//Predator/Survivor
1 Inflatable Hull
Floor Boards
Wolf Cub 2 pieces
Predator, and Survivor 3 pieces
Aluminum floor joiners
Wolf Cub 2 pieces
Predator, and Survivor 3 pieces
Foot or hand straps (unattached)
Wolf Cub 2 pieces
Predator, and Survivor 3 pieces
1 Registration Kit (optional)
1 Dual action Bravo Hand Pump
1 Small puncture repair kit
Warranty / Registration card
Assembly
Wolf Cub/Predator/Survivor .
STEP 1. Insert rear floor board STEP 2. Insert front floorboard
(place aluminum H sections over the ends of both back and front boards)

5
STEP 3, 4 and 5: Insert middle section, join with floor joiners and press down. Place the edge of the
floorboard down under the floor rubber as shown along both sides of boat.
Step 6: Inflate using pump included to 6 PSI
Outboard Installation

6
WARNING!
Be sure to bolt your motor in place.
The transom is designed to accommodate the Nissan &
Mercury line of Outboards. However other outboards
can still be mounted. Some minor modifications may be
necessary to ensure proper installation. If you are not
using Nissan outboards please feel free to contact our
toll free technical service at: 1-877-937-8270.
Place your outboard on the transom plate centered.
You may want to raise and lower your outboard for
better performance depending on the water conditions.
If the water is rough, position your outboard in the
lowest position possible. Flat water may require a
higher setting to get the desired performance.
If additional adjustment is desired, be sure that the
water pickup is still getting water to ensure proper
outboard cooling. Be sure to drill holes through the
plate too securely attach the outboard. For remote
steering outboards, please consult a dealer near you for
proper installation.

7
MAINTANENCE
Care of Your SeaWolf Inflatable
Your new SeaWolf Inflatable is built with only the finest in materials. The hull material is PVC and has
been treated with UV protection at the factory. You inflatable is manufactured to handle both fresh and salt
water. Be sure to follow the below instructions to ensure a long life for your inflatable.
NEVER WASH YOUR INFLATABLE WITH;
• A CLEANER CONTAINING BLEACH
• MEK OR ACID TONE
• GASOLINE
• PAINT OR LAQUER THINER
• WD-40 OR ANY OTHER OIL
Prior to using it may be good to apply an inflatable boat protectant (contact dealer).
Use soap and water to remove all lose dirt after using. For tuff stains please contact your nearest Inflatable
dealer for options. If you plan to leave your inflatable in the water for extended periods of time, you
should consider bottom paint. (See Dealer) Try to keep your inflatable covered from the direct sun for
extended periods of time, as anything UV protected it will eventually start to dry and fade. It is
recommended that you add UV protection after washing with any tuff staining removing product and at
least 1 time per month during the hot summer.
STORAGE
Prior to storing your inflatable for the winter or for whatever reason, you must first remove the floors.
Clean and dry the boat completely. Roll it up if you wish. It is not important to keep it warm but if it dose
get cold, DO NOT ATTEMPT TO UNROLL IT OR MOVE IT AROUND. Keep it in an out of the way
place to ensure that it dose not get damaged. When PVC gets cold it may crack. It is made of plastic.
Allow it to warm to at least 50 degrees before attempting inflation after the cold winter.
CONTACT YOUR DEALER FOR MOTOR
MOUNTING INSTRUCTION

8
Call Toll Free 1-877-937-8270
Are you looking for a way to add registration numbers,
boat names or graphics to your Inflatable Boat?
If So,
Like all inflatable owners you are limited to a few
choices
Tie on a board.
Magic markers.
the current best is
Inflatable Paint!
It’s Messy, and Expensive, … it runs, rubs off, smears,
scratches, and quickly fades.
FINALLY!

9
Registration Numbers
$99.95 (Add $5.00 for shipping)
Quick and easy installation
To place your order call Toll Free;
1-877-937-8270
Allow 7-10 working days for delivery.
24 HOUR EXPRESS DELIVARY AVAILABLE
(ask for details)
Sorry,
No C.O.D orders.
To place your order call Toll Free;
1-877-937-8270