InFocus INF7020 User manual

INF7020
Regulatory model: PN-L702B
p/n: 009-1422-00
Quick Setup Guide

Page 1INF7020 Quick Setup Guide
What's Included
Quick Start
Guide
• Monitor
• Wireless keyboard and mouse*
• Stylus
• Quick Start guide
• Remote
• Camera
• Antenna (2)
• Sound bar (not shown)
• Sound bar remote (not shown)
• Sound bar bracket (not shown)
*Keyboard and mouse not included in all countries. For setup purposes, a keyboard and mouse are recommended. Any standard
wired or wireless mouse or keyboard, connected through the computer module USB ports is supported.
IMPORTANT: A stand or cart is recommended for use with this monitor.

Page 2
Setup
IMPORTANT: Beforefollowingtheseinstrucons,yourmonitormustbewallmountedoraachedtoastandorcartwhichmeets
orexceedsthesafetyrequirementsforthismonitorandfollowsallmanufacturersafetyprecauonsandinstrucons.
Removing Orange Tape
AermounngtheINF7020monitor,carefullyremoveallorangetape.
Attaching the HD Video Conferencing Camera
1) Center the camera along the top edge of the monitor, aligning the camera bracket with the screw hole on the back of the moni-
tor.
2) Securelyaachthecamerabrackettothemonitorusingtheprovidedscrew.
3) PlugtheUSBcableintoanavailableUSBslotonthecomputermodule.NOTE: It is not necessary to unwrap the cable. It has
been pre-measured.
4) Removetheplasclmfromthecameralens.
5) Manuallyltandpanthecamera(+/40°)asdesired.
Attaching the Antennas
1) Aachthetwoantennasintothecomputermoduleonthebackofthemonitorbyturningtheantennasclockwiseunlsecure.
2) Adjust the angle of the antennas as needed to maximize wireless signal strength.
Attaching the Sound Bar
RefertotheSoundBaruserdocumentaon.

Page 3INF7020 Quick Setup Guide
Cable Connection
1) Cutthezipeholdingthepowercordtothebackofthemonitor.
2) Connect the power cord to an AC outlet.
3) PressthemonitorpowerswitchtotheONposion.
WARNINGS:
• Themainpowermustbeturnedonandowiththemonitorpowerswitch.Donotconnectordisconnectthepowercordorturn
thebreakeronandowhilethemonitorpowerswitchison.
• WhenswitchingthemonitorpowerswitchorthePOWERbuonoandandbackon,alwayswaitforatleast5seconds.For
completeelectricaldisconnecon,pulloutthemainplug.
Turning the INF7020 On/Off
Thecomputermodule,soundbarandmonitorfunconindependently.Eachcomponentmustbecontrolledseparately.
TO TURN THE INF7020 ON
1) PressthecomputermodulePOWERbuonlocatedonthebackofthemonitor.
2) PressthePOWERbuonlocatedonthefrontofthemonitor(orusethemonitor'sremote).
3) Ifinstalled,pressthesoundbarPOWERbuonon.Thecomputermodule,monitorandsoundbarturnon.
POWER BUTTON
POWER LED
TOUCH PANEL LED

Page 4
NOTE: Ifthepowerisnotturningon,checkthepowerswitchonthebackofthemonitorandverifythatallpowercordsandpower
supplies are properly connected and connected to AC.
TO PUT THE INF7020 MONITOR INTO STANDBY
1) PressthePOWERbuononthefrontoftheINF7020(orusethemonitor'sremote).
2) Ifyouwanttoputthecomputermoduleintostandbymode,pressthePOWERbuonlocatedonthebackofthemonitor.
TO COMPLETELY POWER DOWN THE INF7020
1) PressthePOWERbuononthefrontoftheINF7020(orusethemonitor'sremote).
2) PressthecomputermodulePOWERbuonlocatedonthebackofthemonitor.
3) Turnothepowerswitchonthebackofthemonitorandunplugthepowercordfromthepoweroutlet.
NOTE:WhentogglingthepowerswitchorthePOWERbuonoandon,waitatleast5seconds.
For More Information about the INF7020
FormoreinformaonabouttheINF7020,refertotheINF7020HardwareGuideandtheMondopadSowareGuideonthewebat
www.infocus.com/INF7020.