INIM Electronics Air2 Series Assembly instructions

"JS4NBSUZ8
8JSFMFTT JOEPPS TPVOEFS
*OTUBMMBUJPO BOE QSPHSBNNJOH NBOVBM

Table of contents
1. Air2 system description 3
2. Description Air2-Smarty/W 4
2.1 Description of parts 5
2.2 Technical specifications Air2-Smarty/W 6
3. Sounder/flasher functions 7
3.1 Types of signalling 7
3.2 Sounder/flasher activations 7
3.3 Faults and tampers 8
4. Installation of Air2-Smarty/W 9
4.1 Enrolling a wireless device 10
4.2 Battery replacement 10
5. Programming of Air2-Smarty/W 11
5.1 Wireless sounder/flasher parameters 11
5.2 Programming the patterns 12
5.3 Real-time 12
6. General information 14
6.1 About this manual 14
6.2 Manufacturer's details 14
6.3 Notes from the Manufacturer 14
6.4 Simplified EU Declaration of Conformity 14
6.5 Documents for the users 15
6.6 WEEE 15
2Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 3
1. Air2 system description
All anti-intrusion systems INIM can manage the two-way wireless system Air2 characterized by a MHz carrier
frequency 868 MHz.
The system components Air2 are:
Air2-BS200/50 transceiver module, 50 terminals
Air2-BS200/30 transceiver module, 30 terminals
Air2-BS200/10 transceiver module, 10 terminals
Air2-KF100/S 4 button remote-control key
Air2-Ergo/S 4 button remote-controlkey
Air2-Pebble/S 4 button remote-control key
Air2-MC200 magnetic contact with shock and tilt sensor in white or brown
Air2-MC300 magnetic contact with two I/O terminals, in white or brown
Air2-FD100 smoke detector
Air2-Aria/W keypad with graphic display
Air2-Hedera outdoor sounder, in white or chrome effect
Air2-Smarty/W indoor sounderflasher
Air2-DT200T dual technology curtain detector, in white or brown
Air2-XIR200W PIR detector, 12 m
Air2-XDT200W dual technology curtain detector
Air2-UT100 universal transceiver
Air2-ODI100W outdoor wireless dual-infrared detector
Air2-OTT100W outdoor wireless triple-technology detector
Technicalspecifications of the system Air2
Operating frequency
range 868.0 - 868.6 MHz
selectable channels 868.1, 868.3, 868.5 MHz
RF output power 25mW e.r.p.
Communication type Two-way
Modulation GFSK
Device supervision from 12 to 250 minutes
/PUF
In order tocomply with theEN 50131-1 standards the alarm system supervision time must be below 120 minutes.

2. Description Air2-Smarty/W
2. Description Air2-Smarty/W
Wireless sounder/flasher for outdoor use Air2-Smarty/W interfaces with control panels INIM via an Air2-
BS200 transceiver through which it is controlled and monitored by the control panel.
The sounder/flasher can be programmed from the control panel via software that allows the configuration of
the various parameters (tone, maximum alarm time, flash rate, signalling activation mode, etc.) and the activ-
ation of different signals for different events.
The control panel, via wireless system at all times Air2 is capable of monitoring tamper, low battery, fault and
battery level signals.
Air2-Smarty/W it provides self-diagnostic functions for prompt identification of faults and, during the install-
ation phase, allows the operator to choose the type of signal type forwireless-signal loss events.
The super bright LED flasher offers long autonomy and reduced power consumption and has two ancillary
signal LEDs.
'VODUJPOT
Piezoelectric horn
Super bright LED-technology flasher
3.6V 2.8Ah battery
Anti-opening and protection
Tamper-protection device
Degree of protection IP31
Communication with the transceiver Air2-BS200 two-way at 868
Direct control via control panel
Battery with test circuit
Programmable sound-output time
4 programmable volume levels
Programmable flasher sequence
Programmable flasher time
STATUS and PRG LEDs activation via control panel
#BUUFSZ
The sounder/flasher is powered by a 3.6V 2.8Ah (ER17505M) battery to be located in its housing inside the
casing and connected up during the installation phase.
The battery may not be capable of meeting the declared duration as this depends on how the sounder-
/flasheris employed and the number and length of activations.
Used batteries must be disposed of in accordance with the information provided in the leaflet inside the pack-
age.
1BDLBHFDPOUFOUT
Sounder/flasher Air2-Smarty/W
2 wall plugs for mounting the backplate and tamper bracket
Drilling pattern
Installation manual
1 battery to be connected
4Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 5
2.1 Description of parts
2.1 Description of parts
<">LJ Locations for the cover pin
<#>LJ Battery
<$>LJ Battery connector
<%>LJ ENROLL button
<&>LJ Piezoelectric horn
<'>LJ Tamper microswitch: Dis-
lodgement
<(>LJ Tamper microswitch: Open
cover
<)>LJ Red STATUS LED
<*> Green PRG LED
<+>LJ LED flasher
<,>LJ Cover screw
<->LJ Coverpin
<.>LJ Cable entry
</>LJ Mounting screw location
<0>LJ Tamper-screw location

2. Description Air2-Smarty/W
2.2 Technical specifications Air2-Smarty/W
Battery
Warningdevice type For indoor use, self-powered, type W
type ER17505M 3,6V 2,8Ah with connector
estimated life 3 years (depending on activations)
“Low battery” fault voltage Less than 3.2V
Current draw
during standby 50µA
maximum 200mA
Acoustic output type tones
Sound pressure at 1m. 85dB(A)
Carrier frequency 1148 Hz
Flash rate per minute (programmable) 36 - 56
Maximum alarm-time (programmable) 4 min
Operating environmental conditions
Temperature from -25 to +60°C
Relative humidity ≤93% without condensation
Degree of protection IP31
Security grade 2
Environmentalclass IV
Dimensions (W x H x D) 111 x 75 x 30 mm
Weight 130 g
Number of sounder/flasher units supported by Air2-BS200 Maximum 4
6Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 7
3.1 Types of signalling
3. Sounder/flasher functions
The sounder/flasher Air2-Smarty/W provides various audible and visual signals. The signals will activate or
deactivate in accordance with the sounder/flasher settings Air2-Smarty/W or the connected control panel.
The parameters of each signal can be programmed individually, combined with other signals, or deac-
tivated.
3.1 Types of signalling
'MBTIFS
The high intensity luminous signalis achieved by means of high-efficiency LEDs ( LEDflasher) which, due to
their extra-low power consumption, provide optimum autonomy.
45"564-&%13(-&%
The two LEDs on the sides of the flasher can be used for signalling purposes as well as during installation
operations ( RedSTATUSLED,GreenPRGLED).
These two LEDs, if suitably programmed, will signal device faults and tamperevents.
"VEJCMF TJHOBMMJOH
The speaker emits an audible signal which can be programmed for tone (3 tones available), duration,
volume and associated events.
3.2 Sounder/flasher activations
Sounder/Flasher units Air2-Smarty/W can be triggered by signals from the intrusion control panel and also
by events generated by the sounder/flasheritself.
$POUSPMQBOFM FWFOUBDUJWBUJPOT
The occurrence of control-panel events (activations or resets) can activate a sounder/flasher and generate
signalling.
Each event can be associated with one or more sounder/flashers, configured as “Outputs” during the event
programming phase. Each event can be associated with one of the tone types (patterns) available.
4PVOEFSGMBTIFSFWFOUT
The sounder/flasher processes the signals detected by the devices it is equipped with, in such a way as to
generate events to which one or more signals can be associated:
Low battery
Open casing
Device dislodgement
Loss of wireless communication with the control panel
Wireless noise

3. Sounder/flasher functions
/PUF
The “Open casing” event does not trigger audible signals when the connected intrusion control panel is operating
in “Programming” mode.
%FBDUJWBUJPOT
Signalling will cease when one of the following conditions occurs:
Deactivations from the control panel:
with the “Stop alarms” shortcut
by accessing maintenance mode
by pre-set disarm scenarios
with the events associated with the causes of shutdown
The alarm condition clears
The maximum alarm time expires
If an alarm condition exceeds the maximum soundersignalling time, the signalling will be interrupted.
3.3 Faults and tampers
The STATUS and PRG LEDs will signal fault or tamper conditions on the sounder/flasher only when set up
to do so during the programming phase.
/PUF
This type of activation prevents the control panel from activating the LEDs.
This signalling consists of a series of flashes. If several conditions are detected simultaneously, both LEDs
are capable of signalling the events consecutively.
LED Number of blinks Event
STATUS 1
Fault
Low battery
2Loss of communication with the control
panel
PRG 1 Tamper Open casing tamper
Dislodgement tamper
Fault signalling will stop automatically when the cause of the fault clears.
8Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 9
4. Installation of Air2-Smarty/W
1. Choose a suitable mounting placement.
The sounder/flasher must be installed high up on a flat surface/wall.
Ferromagnetic materials which are located in the vicinity of the mounting position can influence the mag-
netic field and can result in the reduced operating capacity of the device.
2. Remove the cover by first unscrewing the screw then lifting the catch on the base ( Cover screw).
3. Using the wall plugs, attach the base to the wall.
4. Insert the tamper-protection screw into its location ( Tamper-screw location).
5. Connect the battery to the connector on the PCB ( Batteryconnector) and place it in its housing.
The STATUS LED will alternate 5 flashes and 5 second pauses (waiting to be enrolled).
6. Enroll the device.
The STATUS LED will alternate 3 flashes and 3 second pauses (waiting for the dislodgement/ Open tamper
device to close).
7. Close the cover by positioning the pin in its location on the base, then turn it until the catch clicks
closed.
The STATUS LED will flash with a frequency of one flash per second for15 seconds.
The STATUS LED will stop flashing and the sounder/flasher will be ready to operate.

4. Installation of Air2-Smarty/W
4.1 Enrolling a wireless device
The enrolling procedure allows you to associate a wireless device INIM with the transceiver Air2-BS200
which acts in conjunction with the intrusion control panel.
This procedure varies depending on the control panel in use and the programming software orapplication:
1. Access the control panel programming.
2. Select the device to be enrolled in accordance with its type:
an input terminal, for a detector (motion detector, magnetic contact, etc.)
an output terminal, for an output device connected to a terminal of a magnetic contact Air2-
MC300
a keypad
a sounder/flasher
a key, for a remote control device, selecting as the associated reader the one simulated by the
transceiver
3. Set the device as “Wireless”.
4. Start the learning phase from the control panel.
5. Press the ENROLL button on the wireless device.
4.2 Battery replacement
When changing the battery, it is advisable to press the ENROLL button in order to be sure that the device is
synchronized with the wireless transceiver.
10 Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 11
5.1 Wireless sounder/flasher parameters
5. Programming of Air2-Smarty/W
Programming sounder/flasher units Air2-Smarty/W can only be done through the control panel pro-
gramming software.
On accessing the software, it is necessary to open a solution, configuration of the real system to be
designed. The system project must provide for the addition of wireless sounders/flasher units.
For a new installation or the creation of a new solution, it is necessary to select a sounder/flasher from the
devices available and include it in the system project.
If you are using an already programmed solution, you must check that the system includes a sounder-
/flasher. At this point it is possible to proceed with the programming of the sounder/flasher.
/PUF
Once the programming has been completed andthe parameter have been “written” on the control panel, it will
take at least 30 seconds for the device to become operative.
5.1 Wireless sounder/flasher parameters
After the selection of a wireless sounder/flasher, the programming software provides the following para-
meters in addition to the parameters common to all “wired” sounder/flasherunits:
Communicationloss sig-
nalling
It is possible to select when the sounder/flasher is to activate in the event of communication loss with
the control panel:
never
only when wireless jamming affects communication
each time communication is lost
In the latter two cases it is necessary to indicate the “Wireless supervision time”, in minutes, after
which if the communication continues to be absent the sounder/flasher will activate.
Enable anti-tampersig-
nalling Options that enable the signalling of tamper or low battery charge
Enable battery inef-
ficient signalling
PRG/STATUS LEDactiv-
ation
Parameter to indicate the source (control panel or the sounder/flasher itself) of the activation of the
PRG and STATUS LEDs.
The selection of one of the two LED activation sources excludes the other.
Sounder/flasher LED
activations Each sounder/flasher LED (PRG or STATUS) provides 5 options which allow you to select the con- trol panel event that will activate the LED.
Cause of deactivationof
sounder and flasher A maximum of 5 options allow you to select a control panel event that will deactivate the sounder and flasher.
Inversion
If the option is disabled, the LED or sounder and flasher will switch off when activation of the event
occurs.
If the option is enabled, the LED or sounder and flasher will switch off when deactivation of the event
occurs.

5. Programming of Air2-Smarty/W
5.2 Programming the patterns
By selecting the system “Sounder/Flasher” category, it is possible to program the tone types (patterns) for all
the sounder/flasherunits in the configuration.
Description
Description of the pattern to program.
Burglary
Burglary low volume
Fire
Tamper
Pre-alarm
Automation
Squawk
Chime
Activate sounder Enable/Disable sounder activation
Tone Sound of the audible signal 3 types available.
Sounder duration Sounder activation time from 1 to 127 seconds or from 1 to 127 minutes
Volume Sound level of the sounder
Activate flasher Enable/Disable flasher activation
Flash type Flash rate (number of flashes per minute). 36 flash/min
56 flash/min
Flasherduration Flasher activation time from 1 to 127 seconds or from 1 to 127 minutes
Activate STATUS LED Enable/Disable activation of the STATUS LED
Activate PRG LED Enable/Disable activation of LED PRG output.
%FGBVMU
The following default patterns are available, each of which can be modified:
Description Sounder/flasher Sounder dur-
ation Tone Volume Flasher Flasher duration Flash type STATUS/ PRG LED
Burglary ON 3 minutes 1 high ON 3 minutes 56 OFF
Burglary low
volume ON 4 minutes 1 low ON 4 minutes 56 OFF
Fire ON 3 minutes 3 high ON 3 minutes 56 OFF
Tamper ON 127 seconds 1 high ON 127
seconds 36 OFF
Pre-alarm ON 30 seconds 1 low ON 30 seconds 36 OFF
Automation ON 3 seconds 1 low OFF OFF
Signalling ON 1 second 3 low ON 1 second 56 OFF
Chime ON 3 seconds 3 low ON 3 seconds 56 OFF
Total cut off OFF / / low OFF / / OFF
5.3 Real-time
For each of the configured sounder/flasher units, the software provides a direct software-to-sounder/flasher
connection which allows visualization of the current values of the following features of the wireless sounder-
/flasher.
In this section, the monitoring window lists the parts of the sounder/flasher whose status is represented by
icons/LED:
12 Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 13
5.3 Real-time
LED Colour Status
Tamper
Green
Sounder/flasher
not in tamper
status
Red
Sounder/flasher
in tamper status
(open or dis-
lodged)
Battery
inefficient
Green Battery charged
Red
Battery charge
low (below
40%)
Sounder
active
Green Audible sig-
nalling Off
Red Audible sig-
nalling On
Flasher
active
Green Visual sig-
nalling Off
Red Visual sig-
nalling On
STATUS
LED ON
Green STATUS LED
off
Red STATUS LED
On
PRG LED
ON
Green PRG LED off
Red PRG LED On
Signal
reception
level
Series of notches that represent the reception level of the wireless signal of the sounder/flasher as received by the
transceiver Air2-Smarty/W.
Battery
charge
level Percentage of the sounder/flasher battery charge.
.POJUPSJOH XJSFMFTT
This software section starts a monitoring phase on the variation of the signal transmitted by the device and
background noise detected over time.

6. General information
6. General information
6.1 About this manual
Manual code:DCMIINE0A2SMARTYW8E
Revision: 101
Copyright: The information contained in this document is the sole property of Inim Electronics S.r.l.. Copy-
ing, reprinting or modification of this document, in part or as a whole, is not permitted without prior autho-
rization in writing from Inim Electronics S.r.l.. All rights reserved.
6.2 Manufacturer's details
Manufacturer:Inim Electronics S.r.l.
Production plant:Centobuchi, via Dei Lavoratori 10
63076 Monteprandone (AP),Italy
Tel.: [phone]
Fax: [phone]
E-mail [e-mail]
Web: www.inim.biz
The persons authorized by the manufacturer to repair or replace the parts of this system have authorization
to work only on devices marketed underthe brand Inim Electronics.
6.3 Notes from the Manufacturer
The devices Air2 are certified by IMQ-Sistemi di sicurezza (Italian certification body).
The information relating to the power-supply batteries required by the devices Air2 are provided in the fol-
lowing TechnicalSpecification table.
The manufacturer cannot guarantee the declared battery life.
"UUFOUJPO
Do not use batteries other than those indicated by the manufactureras they may
explode.
6.4 Simplified EU Declaration of Conformity
Hereby, Inim Electronics S.r.l. declares that the radio equipment type Air2-Smarty/W is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet
address: www.inim.biz.
14 Installation and programming manual- 101

Air2-Smarty/W | © 2020 Inim Electronics S.r.l. 15
6.5 Documents for the users
6.5 Documents for the users
Declarations of Performance, Declarations of Conformity and Certificates concerning to Inim Electronics
S.r.l. products may be downloaded free of charge from the web address www.inim.biz, getting access to
Extended Access and then selecting "Certifications" or requested to the e-mail address [e-mail] or
requested by ordinary mail to the address shown in this document.
Manuals may be downloaded free of charge from the web address www.inim.biz, getting access to the
reserved area, afterthe login, and then to the section of each product.
6.6 WEEE
Informative notice regarding the disposal of electrical and electronic equipment (appli-
cable in countries with differentiated waste collection systems)
The crossed-out bin symbol on the equipment or on its packaging indicates that the product must be
disposed of correctly at the end of its working life and should neverbe disposed of togetherwith gene-
ral household waste. The user, therefore, must take the equipment that has reached the end of its working
life to the appropriate civic amenities site designated to the differentiated collection of electrical and elec-
tronic waste. As an alternative to the autonomous-management of electrical and electronic waste, you can
hand over the equipment you wish to dispose of to a dealer when purchasing new equipment of the same
type. You are also entitled to convey for disposal small electronic-waste products with dimensions of less
than 25cm to the premises of electronic retail outlets with sales areas of at least 400m2, free of charge and
without any obligation to buy. Appropriate differentiated waste collection for the subsequent recycling of the
discarded equipment, its treatment and its environmentally compatible disposal helps to avoid possible
negative effects on the environment and on health and favours the re-use and/orrecycling of the materials it
is made of.
Information about disposal of batteries and accumulators (applicable in Countries
with separate collection systems)
This marking on batteries and/or their manual and/or their packaging, indicates that batteries of this
products, at the end of their working life, should not be disposed of as unsorted municipal waste, but must
be object of a separate collection. Where marked, the chemical symbols Hg, Cd o Pb indicate that the bat-
tery contains mercury, cadmium or lead above the reference levels of the directive 2006/66/EC. If batteries
are not properly disposed of, these substances, together with other ones contained, can cause harm to
human health and to the environment. To protect human health and the environment, to facilitate treatment
and recycling of materials, separate batteries from other kind of waste and use the collection scheme stated
in your area, in accordance to current laws. Before disposing of the above, it's appropriate to remove them
from their holders avoiding to damage them or causing short circuits.

[email protected] _ www.inim.biz
Via dei Lavoratori 10, Loc. Centobuchi
63076 Monteprandone (AP) ITALY
Tel. [phone] _ Fax [phone]
DCMIINE0A2SMARTYW8E-101-20200921