Humminbird HDR 650 User manual

531874-3_A
HDR 650 Installation
and Operations Manual
HDR 650 Installation
and Operations Manual
HDR_650_Ma ual_531874-3EN_A.qxp_531440-2_A - HDR 610 IG.qxd 7/18/18 10:07 AM Page A

Ta
How
Inst
In
Ope
T
P
K
U
S
D
S
Ma
H
T
Tro
H
Thank You!
Thank you for choosing Humminbird®, America's #1 name in fishfinders.
Humminbird has built its reputation by designing and manufacturing
top-quality, thoroughly reliable marine equipment.
Your Humminbird is designed for trouble-free use in even the harshest marine
environment. In the unlikely event that your Humminbird does require repairs,
we offer an exclusive Service Policy. For complete details, see the separate
warranty card included with your unit.
Contact Humminbird Customer Service at 1-800-633-1468 or visit our Web site
at humminbird.com.
WARNING! This device should not be used as a navigational aid to prevent
collision, grounding, boat damage, or personal injur . When the boat is moving,
water depth ma change too quickl to allow time for ou to react. Alwa s operate
the boat at ver slow speeds if ou suspect shallow water or submerged objects.
WARNING! Disassembl and repair of this electronic unit should onl be
performed b authorized service personnel. An modification of the serial number
or attempt to repair the original equipment or accessories b unauthorized
individuals will void the warrant .
NOTE: The procedures and features described in this manual are subject to change
without notice. This manual was written in English and ma have been translated
to another language. Humminbird is not responsible for incorrect translations or
discrepancies between documents.
Humminbird®is a registered trademark of Johnson utdoors Marine Electronics, Inc.
© 2018 Johnson utdoors Marine Electronics, Inc. All rights reserved.
HDR_650_Ma ual_531874-3EN_A.qxp_531440-2_A - HDR 610 IG.qxd 7/18/18 10:07 AM Page B

Table o Contents
i
How Sonar Works 1
Installation Overview 2
Installing the DR 650 .................................................................................................... 3
1. Locating the RD 650 Mounting Position ............................................................ 4
2. Cutting the Mounting ole .................................................................................... 4
3. Customizing and Assembling the DR 650 .......................................................... 5
4. Installing the DR 650 .......................................................................................... 6
5. Installing the Buzzer................................................................................................ 7
6. Connecting to the Power Supply............................................................................ 7
7. Installing the Transducer ........................................................................................ 8
8. Connecting the Transducer Cable.......................................................................... 9
9. Testing and Finishing the Installation.................................................................... 9
Operating the HDR 650 10
The DR 650 Control ead............................................................................................ 10
Power On/Off.................................................................................................................. 11
Key Functions Overview ................................................................................................ 11
Units................................................................................................................................ 12
Shallow Alarm ................................................................................................................ 13
Deep Alarm .................................................................................................................... 14
Set Offset (waterline or keel) ........................................................................................ 15
Maintenance 16
DR 650 Maintenance .................................................................................................. 16
Transducer Maintenance .............................................................................................. 16
Troubleshooting 17
DR 650 Doesn't Power Up .......................................................................................... 17
ers.
ring
rine
airs,
rate
site
to
nt
g,
te
be
er
ed
ge
ed
or
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page i

Table o Contents
ii
Ho
Son
uses
Digi
the
the
surf
puls
and
Son
(70
can
No Bottom Reading on the Display .............................................................................. 18
No Continuous Depth Display in Very Shallow Water ................................................ 18
Screen Fades, Images are not Sharp............................................................................ 18
Bottom Reading Disappears During a ard Turn ........................................................ 18
Specifications 19
Contact Humminbird 22
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page ii

How Sonar Works
Sonar technology is based on sound waves. The DR 650 Digital Depth Sounder
uses sonar to determine depth directly below the transducer. Your DR 650
Digital Depth Sounder consists of two components: the DR 650 sonar unit and
the transducer. The sonar unit contains the transmitter and receiver, as well as
the user controls and display. The transducer is mounted beneath the water
surface and converts electrical energy from the transmitter into mechanical
pulses or sound waves. The transducer also receives the reflected sound waves
and converts them back into electrical signals for display on the sonar unit.
Sonar is very fast. A sound wave can travel from the surface to a depth of 240 ft
(70 m) and back again in less than 1/4 of a second. It is unlikely that your boat
can "outrun" this sonar signal.
1How Sonar Works
. 18
. 18
. 18
. 18
19
22
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 1

Installation Overview
Before you start installation, we encourage you to read these instructions
carefully in order to get the full benefit from your DR 650 Digital Depth Sounder.
In addition to the hardware included in the installation kit, you will also
need the following supplies:
•powered hand drill and various drill bits, including a 2 1/8" hole saw if your
boat does not have an existing gauge hole
•Phillips-head and flat-head screwdrivers
•ruler or measuring tape
•pen or pencil
•12 Volt power source (your boat's battery)
•marine-grade silicone sealant (for sealing drilled holes)
NOTE: If you are wiring directly to the boat's battery, you will also need a 1 Amp
fuse and a fuse holder.
2
Installation
Ins
You
you
insta
step
soun
1.
2.
3.
4.
5.
6.
7.
8.
9.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 2

ions
der.
also
your
p
Installing the HDR 650
You will install your DR 650 depth sounder first, then your transducer. When
you are done with both of these installation tasks, you should perform a final
installation test before operating your DR 650. Perform the following high-level
steps by following the instructions in each numbered section to install the depth
sounder:
1. Locating the RD 650 mounting position
2. Cutting the mounting hole
3. Customizing and assembling the DR 650
4. Installing the DR 650
5. Installing the buzzer
6. Connecting to the power supply
7. Installing the transducer: See the transducer installation guide included
with your product.
8. Connecting the transducer cable
9. Testing and finishing the installation
3Installation
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 3

1. Locating the HDR 650 Mounting Position
You must select an appropriate mounting location for the DR 650. Consider
different positions on the console or deck of the boat, and note the following:
•The cables for the transducer and power must reach the mounting location.
Extension cables are available.
•The mounting surface should be visible to the boat operator and adequately
supported to protect the DR 650 from excessive wave shock and vibration.
•Allow at least 2" clearance at the back, sides, and top of the unit for
connection, air flow, and ease of installation and removal.
2. Cutting the Mounting Hole
Once you have selected your mounting location, perform the following steps:
1. Mark the desired mounting location, then drill a pilot hole.
2. Drill a 2 1/8" diameter hole using a hole saw and hand drill. This is a
standard hole saw readily available for rental or purchase. If you prefer, any
marine service shop can perform this task.
Choosing Mounting Hole Location
4
Installation
3. C
Your
cust
1.
2.
CA
is
it
3.
4.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 4

ider
g:
tion.
ately
tion.
for
:
is a
any
3. Customizing and Assembling the HDR 650
Your DR 650 includes a variety of face plates and trim rings so you can
customize the appearance.
1. Select one face plate and one trim ring.
2. Peel off the protective backing from the face plate. Be careful not to let the
adhesive touch anything prematurely.
CAUTION: In order to provide a lasting, waterproof bond, the face plate adhesive
is extremely sticky, and you will N T be able to re-position it once you have stuck
it onto the face of the HDR 650.
3. Carefully line up the face plate with the face of the DR 650. Press the face
plate into place so that all keys are accessible and the display is visible (see
illustration).
4. Align the inside tabs of the trim ring with the DR 650 tabs, and snap the
trim ring onto the front of the DR 650 (see illustration).
HDR 650
Face Plate
Trim Ring
Tabs
5Installation
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 5

4. Installing the HDR 650
After the mounting hole has been cut (see section 2), continue the installation as
follows:
1. Remove the gasket and collar by unscrewing them from the DR.
2. Insert the DR through the front hole of the dashboard.
3. From the rear of the dashboard, install the gasket and collar onto the DR.
4. and-tighten the collar until the
DR is securely mounted in the
dashboard. Make sure that the
face of the DR stays oriented
upright.
Hand-tightening the Collar
Collar
Gasket
Dashboard View HDR 650 Control Head
Attaching the Gasket and Collar
6
Installation
5. I
1.
6. C
Use
supp
•
•
•
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 6

n as
DR.
5. Installing the Buzzer
1. Secure the buzzer to a nearby wire bundle
using the cable ties (included).
6. Connecting to the Power Supply
Use the following information to connect your DR 650 to an appropriate power
supply:
• If your boat has an electrical system, there is probably a fuse panel in the
console area that can be used to attach the DR 650 power cable.
• If a fuse terminal is available, use crimp-on type electrical connectors (not
included) that match the terminal on the fuse panel. Attach the black wire
to ground and the red wire to 12 VDC power. You must use a 1-Amp fuse in
the connection.
• 36" of power cable is included; you may shorten or lengthen this cable using
18-gauge, multi-strand copper wire.
Buzzer
Securing the Buzzer
7Installation
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 7

CAUTION: Some boats have 24 or 36 Volt electrical systems. Make sure that your
HDR 650 is connected to a 12 VDC power supply. Use a voltage conditioner for
variable inputs.
NOTE: Humminbird is not responsible for over-voltage or over-current failures. The
control head must have adequate protection through the proper selection and
installation of a 1 amp fuse.
7. Installing the Transducer
Proceed to the transducer installation guide (included with your product) to install
the transducer.
Before you start installation, we encourage you to read the instructions carefully
so that you may understand the installation requirements.
1a. If a fuse terminal is available, use crimp-on type electrical connectors
(not included) that match the terminal on the fuse panel. Attach the
black wire to ground (-), and the red wire to positive (+) 12 VDC power.
Install a 1 amp fuse (not included) for protection of the unit.
umminbird is not responsible for over-voltage of over-current failures.
or...
1b. If you need to wire the DR 650 directly to a battery, obtain and install
an inline fuse holder and a 1 amp fuse (not included) for the protection
of the unit. umminbird is not responsible for overvoltage or
overcurrent failures.
GROUNDGROUND
POSITIVEPOSITIVE
Inline Fuse Holder
8
Installation
8. C
1.
9. T
Onc
rout
in p
1.
2.
3.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 8

ur
or
he
nd
stall
fully
rs
e
r.
t.
s.
ll
n
or
8. Connecting the Transducer Cable
1. Plug the transducer cable into the matching connector cable on the DR.
NOTE: The connector is keyed to prevent reverse installation, so be careful not
to force the plug into the connector the wrong way.
9. Testing and Finishing the Installation
Once you have installed both the DR 650 and the transom transducer, and have
routed all the cables, you must perform a final test before locking the transducer
in place.
1. Turn on the power source to power on the DR. If the unit does not power
up, make sure the connector is secure and that power is available.
2. The DR will start normal operation. If the digital depth readout displays
on the screen, the unit is working properly.
3. Test and Finalize the Installation: Follow the instructions in the
Transducer Installation Guide: Testing and Finishing the Installation.
You will test the transducer at high speeds, make adjustments, and secure
the installation.
9Installation
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 9

Operating the HDR 650
Your DR 650 Digital Depth Sounder sends a sound wave signal and determines
distance by measuring the time between the transmission of the sound wave and
when the sound wave is reflected off of an object. As your DR 650 transducer
receives sonar signals, it converts them to a digital depth that is shown on the
DR 650 display. The depth reading is continuously updated as you travel across
the water. The liquid crystal display (LCD) offers sharp viewing, even in bright,
direct sunlight, and is continuously lit for nighttime operation.
NOTE: Actual depth capability depends on such factors as bottom hardness, water
conditions, and transducer installation. Units will typically read to deeper depths in
freshwater than in saltwater.
The HDR 650 Control Head
The DR 650 uses a backlit display, together with a 3-button keypad, to control
all user functions. The illustration below shows an example of the digital display.
HD 650
Depth
Alarm Icon
(flashes to
indicate
alert)
Shallow Alarm
Icon
(indicates
Shallow Alarm
is set)
Units
D WN arrow key MENU key UP arrow key
10
Operations
Po
The
the
sour
Ke
1.
2.
3.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 10

ines
an
ucer
the
ross
ght,
er
in
ntrol
play.
rm
rm
Power On/Off
The power is controlle by the power source connecte to the HDR 650. When
the power source is turne on, the HDR 650 is powere on. When the power
source is turne off, the HDR 650 is powere off.
Key Functions O er iew
1. Select a Function: Press the MENU key repeate ly until you reach the
appropriate menu.
2. Adjust the Setting: Press the UP or DOWN arrow key to a just the
setting. Press an hol either key to scroll through the range of settings
quickly.
3. Save: After your selection is ma e, wait 5 secon s for the unit to return
to normal operation. Your settings are save automatically even after the
unit is powere off.
11 Operations
HDR_650_Manual_531874-2EN_A.qx :531440-2_A - HDR 610 IG.qxd 8/31/15 3:09 PM Page 11

Units
The Units control function selects the units of measure for depth readout
and alarm functions. You can set the units of measurement to feet, meters,
or fathoms.
1. Press the MENU key until the Units icon is displayed and flashing on the
screen.
2. Press the UP or DOWN arrow key to scroll through the available units.
(FT = feet, M = meters, FA = fathoms).
3. After your selection is made, wait 5 seconds for the unit to return to normal
operation. Your settings are saved automatically.
Set
Units
12
Operations
Sh
The
1.
2.
3.
4.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 12

dout
ters,
the
nits.
rmal
Shallow Alarm
The Shallow Alarm will sound when the measured depth is less than the setting.
1. Press the MENU key until the Shallow Alarm icon is displayed and flashing
on the screen.
2. Press the UP or DOWN arrow key to change the setting.
(Off, 1 - 20 feet, .1 - 6 meters, or .1 - 3.2 fathoms; Default = Off)
NOTE: The maximum Shallow Alarm setting cannot meet or exceed the current
Deep Alarm setting (see the Deep Alar section).
3. After your selection is made, wait 5 seconds for the unit to return to normal
operation. Your settings are saved automatically, and the Shallow icon will
be visible on the display.
4. Alarm: If the depth of the water is less than the saved setting, the alarm
will sound and the alarm icon will flash on the screen.
Mute: Press any key to mute the alarm.
Adjust: Press the MENU key and follow the instructions in step 2 to adjust
the alarm setting.
Set
Shallow Alarm Icon
13 Operations
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 13

Deep Alarm
The Deep Alarm will sound when the measured depth is greater than the setting.
1. Press the MENU key until the Deep Alarm icon is displayed and flashing on
the screen.
2. Press the UP or DOWN arrow key to change the setting. (Off, 20 - 99 feet,
6 - 30 meters, or 3.3 - 16 fathoms; Default = Off)
NOTE: The minimum Deep Alarm setting cannot meet or drop below the
current Shallow Alarm setting (see the Shallow Alar section).
3. After your selection is made, wait 5 seconds for the unit to return to normal
operation. Your settings are saved automatically, and the Deep icon will be
visible on the display.
4. Alarm: If the depth of the water is greater than the saved setting, the
alarm will sound and the alarm icon will flash on the screen.
Mute: Press any key to mute the alarm.
Adjust: Press the MENU key and follow the instructions in step 2 to adjust
the alarm setting.
Set
Deep Alarm Icon
14
Operations
Se
The
read
tran
1.
2.
3.
4.
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 14

ting.
g on
feet,
he
rmal
ll be
the
djust
Set O set (waterline or keel)
The Set Offset function adjusts the digital depth readout to display depth
readings from the waterline or the keel (lowest point of the boat) instead of the
transducer location.
1. Choose to measure the depth from the keel or waterline.
Keel: Measure the vertical distance between the face of the transducer
and the keel of the boat.
Waterline: Measure the vertical distance between the face of the
transducer and the waterline of the boat.
2. Press the MENU key until Set Offset is displayed and flashing on the screen.
3. Enter your chosen offset measurement as follows:
Keel: Press the DOWN arrow key to enter the
measurement from step 1 as a negative (-)
number. (-1 to -10 feet, -.1 to -3.0 meters, or
-.1 to -1.6 fathoms; Default = 0)
Waterline: Press the UP arrow key to enter the
measurement from step 1 as a positive (+)
number. (+1 to +10 feet, +.1 to +3.0 meters, or
+.1 to +1.6 fathoms; Default = 0)
4. After your selection is made, wait 5 seconds for the unit to return to normal
operation. Your settings are saved automatically, and the offset icon will be
visible on the display.
ffset
Icon
Postive
Number
Waterline Offset
(Set a Positive Number)
ffset
Icon
Negative
Number
Keel Offset
(Set a Negative Number)
15 Operations
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 15

Maintenance
To keep both your DR 650 and your transducer working properly, perform the
following maintenance tasks as needed.
HDR 650 Maintenance
If your DR 650 unit comes into contact with salt spray, simply wipe the affected
surfaces with a cloth dampened in fresh water. Do not use a chemical glass
cleaner on the lens, as chemicals in the solution may cause cracking in the lens.
When cleaning the LCD protective lens, use a chamois and non-abrasive, mild
cleaner. Do not wipe while dirt or grease is on the lens. Be careful to avoid
scratching the lens.
WARNING: Never leave your HDR 650 in a closed car or trunk; the extremely high
temperatures generated in hot weather can damage the electronics.
Transducer Maintenance
If your boat remains in the water for long periods of time, algae and other marine
growth can reduce the effectiveness of the transducer. Periodically clean the face
of the transducer with hot water. Pivoting the transducer up in the bracket may
allow better access for inspection or cleaning.
If your boat remains out of the water for a long period of time, it may take some
time to wet the transducer after it is returned to the water. Small air bubbles can
cling to the surface of the transducer and interfere with proper operation. These
bubbles will dissipate with time, or you may wipe the face of the transducer with
your fingers after the transducer is in the water.
16
Maintenance
Tro
Befo
sect
you
unit
N
pa
m
au
HD
If yo
sure
•
•
•
•
•
Corr
term
HDR_650_Manua _531874-2EN_A.qxp:531440-2_A - HDR 610 IG.qxd 8/27/15 3:02 PM Page 16