Inland 1L35648-U3 User manual

fainiand
USER
MANUAL
USB 3.0 2.5”/ 3.5” External Enclosure
1.0
Introduction
Congratulations
on
your
purchase
of
the
Super-speed
USB
3.0
External
Enclosure.
The
Enclosure
provides
a
fast
and
easy
way
to
add
more
storage
space
to
your
computer.
Please
read
this
manual
carefully
rene
using
this
device.
2.0
Features
and
Specificatio
+
Supports
9.5mm
2.5
inen
SATAMII
HDDs
up
to
2TB
(for
2.5’
HDD
enclosur
»*
Supports
3.5
inch
HDDs
up
to
4TB
(for
3.5”
HDD
enclosure)
+
Convenient
and
Trendy
Design
+
Supports
USB
3.0
super-speed
(5Gbps)
+
Complies
with
USB
2.0
high
speed
(480Mbps),
USB
1.1{12Mbps),
Low
speed
(1.5Mbps)
+
Easy
installation
plug
&
play
and
hot-swappable
+
Supports
One
Touch
Backup
(iL35648-U3)
For
One-Touch-Backup
software»
ave
a
CD
included
in
the
colorbox.
NOTE: One Touch Backup (OTB) is available strictly to
Windows based operating systems; it is not natively
supported
by
Mac
OS.
Instead,
Mac
OS
users
are
encouraged to use the built-in “Time Machine”
software
for
their
back
up
needs.
Requirements:
Windows2000, XP, VISTA,Win7,Win8
Mac
OS
9.1
or
above
Linux
2.4.X
AMD
or
Intel
Pentium
133
MHz
or
better
*
Warranty:
1
year,
limited
Note:
To
enjoy
USB
3.0
super
speed
up
to
5Gbps,
your
computer
must
be
equipped
with
built-in
USB
3.0
port
or
installed
USB
3.0
host
PCi-e
card.
3.0
Packing
Contents
+
USB
3.0
to
HDD
enclosure
+
AC
Power
Adapter
(for
3.5"
HDD
enclosure)
+
User
manual
+
USB
3.0
Super-speed
cable
4.0
Hardware
Setup
*Connect
your
hard
disk
drive
to
the
port
connector
on
the
HDD
enclosure.
+
Connect
the
AC
adapter
to
the
enclosure
and
power
up
the
enclosure
(for
3.5"
HDD
enclosure).
+
Connect
the
enclosure
to
your
computer
using
the
included
USB
cabie.
*
The
computer
should
now
detect
the
new
hardware
.For
Windows2000/XP/VISTA/7/8,
no
driver
installation
is
Please
Proceed
to
chapter
6.0
to
format
your
rive.

5.0 Hardware Installation
Windows
2000/XP/VISTA/7/8
+ No driver installation is necessary.
* The enclosure will be detected by your computer
automatically.
IMPORTANT: Unplugging a device that supports safe
removal
without
first
using
the
“Safely
Remove
Hardware” feature to warn the system can cause data to
be
lost
or
your
system
to
become
unstable.
6.0 Formatting a Hard Drive
WARNING!!
Before
you
partition
your
hard
disk,
please
be
aware
that
this will destroy all your existing data on the drive, so make
sure
you
have
a
backup!
This
step
is
usually
only
required
the
first
time
you
install
a
factory
new
hard
drive
or
if
you
want
to
change
the
existing
format.
Windows 2000/ XP/VISTA/T/8
Step1
Right-click
on
[My
Computer],
choose
[Manage].
A
[Computer
Management]
window
will
appear.
Step2
.
Click
on
[Disk
Management]
on
the
left
part
of
this
window
and
all
connected
disk
drives
will
be
listed
in
the
right
part. Find the Hard Disk that you added with its partition
status
on
the
right.
You
can
create
or
delete
a
new
or
existing
partition by right clicking on this area.
Step3
Right-click
on
the
hard
disk
partition
status
area
and
choose
[New
Partition...].
The
“New
partition
wizard”
will
appear.
Step4
Following the "wizard" instructions to partition and format
your HDD
Step5
Wait until "wizard" finish format your SATA drive. It should
now
appear
in
[My
Computer]
ready
to
use.
Attention:
About
Windows
2000/XP/VISTA/7/8,
Please
choose
NTFS
Format,
When
the
capacity
is
below
32GB,
You
can
choose
FAT32
format.
FAQs:
Q: | can't find the drive under my computer, why?
A: Please make sure your new hard disk has been
partitioned
and
formatted.
Q:
After
plugging
the
USB
port,
the
drive
is
not
spinning
at
all, why?
A:
This
usually
means
the
AC
adapter
is
not
connected
yet,
so
there
is
no
power
(for
3.5”
HDD
enclosure)
The
USB
cable
doesn't
connect
successfully
(for
2.5°
HDD
enclosure)
Q: My device is still recognized as “Unknown device”
A:
This
means
the
driver
installation
is
not
successful,
please unplug the USB cable and re-plug it back in.
Q: My computer doesn't have USB 3.0 port, Can | use
USB 3.0 host adapter?
A:
USB
3.0
host
adapter
works
in
the
same
way
as
the
built-in USB ports.

Installation hard disk drive (1L35648-U3)
Step
1:
Take
out
the
two
screws
on
the
back
Step
3:
First
Take
off
the
left
L/R
panel
from
plastic
frame,
and
then
Insert
15P
and
7P
cable
to
the
hard
disk
Corresponding
145P
and
7P
connector
on
the
HDD.Then
put
HDD
into
the
plastic frame

Step
4:
Gently
move
the
location
of
the
HDD,
HDD's
left
and
right
side
screw
hole
align
the
holes
on
the
plastic
frame,
Then
using L/R panel to fix HDD. (note the difference between L, R)
Step
7:
HDD
Installation
completed
Step
5:
Inset
the
plastic
frame
into
the
aluminum
housing
2/4
3/4