Inland 103M User manual

TILTING FLAT PANEL DISPLAY MOUNT
INSTALLATION GUIDE
Model 103M
Read all instructions carefully before installation.
The installer of this product must verify that the mounting surface, ceiling or wall
will safely support the combined weight of all attached equipment and hardware.
Improper mounting installation and/or exceeding recommended TV weight can
result in damage to the TV and may cause injury or death. This product is not
intended to hold more than the maximum weight advised on the packaging. If you
do not understand these directions, or have any doubts about the safe installation
of your television mount please contact a professional installer to install it for you.
TV Display Size Range: 37" to 70" (940mm to 1778mm)
Maximum Load Capacity: 165lbs (75kgs)
TOOLS REQUIRED:
__ Cordless or Electric Drill
5mm (3/16") Drill Bit for Drywall/Wood Stud Installation
10mm (3/8") Drill Bit for Concrete/Masonry Installation
__ Socket Wrench with 13mm Socket
__ High Quality Stud Finder
__ Long & Regular Phillips Head Screwdrivers
__ Safety Goggles
__ Measuring Tape
__ Level
__ Pencil
Flat Panel Display Mounts
1-Year Limited Warranty
IPSG warrants that this product is free from any defects in materials or work-
manship within one year of purchase date. If such a defect is discovered within
this warranty’s limitations, IPSG agrees at its sole discretion to repair this prod-
uct or to replace it with the same item or one of equal value, free of charge to
the original purchaser. Please return the defective product to the store where
it was purchased.
EXCLUSIONS:
This warranty does not apply to this product if the product has been modi-
ed, tampered with, subjected to abnormal conditions, installed incorrectly,
misused or transferred to another consumer other than the original purchaser.
IPSG requires professional installation for all display mounts and does not
accept damages or liability due to improper installation or installation within
and to structures that cannot support the mount and/or display weight.
Product Registration
Please register this product at www.ipsgproducts.com
Click the “REGISTRATION” link button in the side menu. Enter your name, ad-
dress and contact information. Continue to Step 2 and select your product
type as “LCD/TV/Display Accessories”. In Step 3 choose your model name and
number in the drop down menu and place of purchase to complete your reg-
istration. Your personal contact information will remain private and will not be
sold or given to another company.
If you have questons, please contact us through the side bar menu link on
the www.ipsgproducts.com web page. Enter all of your product and personal
information in the appropriate elds so we can best respond to your inquiry.
© International Products Sourcing Group, Inc. 2010. No part of this user manual may be reproduced in any form or by any
means, mechanical or electronic, including recording, photocopying, or by any information storage or retrieval system,
without permission in writing from IPSG.
Professional
Installation
Recommended

Step 1: Choose a Wall Location
Select the location on a wall where your display will be installed. The best height of
the wall mount is parallel to the eye level of a person who is sitting. Normally, the
horizontal distance of eye level is about 4' from ground level. Go through the following
list when making your choice:
• Determine the exact composition of the wall for your installation. You may need
to re-think your preferred display site in order to install your mount securely in the
wood stud locations available.
• Plan ahead. Make sure you have allowed for clearances once the display is mounted.
• Check the specications of the display for any ventilation requirements.
• Make sure the display will be readily viewable in the room where it is installed.
• Make sure the installation and viewing area is and will be free of obstacles.
• Choose a location that is neither too high nor too low for viewing.
• Choose a location that is near an AC wall outlet.
• Think about the video inputs such as DVI, VGA, PC, S-video, etc. and whether these
cables will be long enough to reach the display once it is mounted.
• Leave some room to the left and right of the installation location for adjustments
when needed.
Using your pencil, mark the location where you want to install your mount and display.
This mark will be the approximate center of the Wall Mount (1). Keep in mind that the
most desirable location may not be the safest location. Your display should hang in a
place where there is low trac and will not endanger anyone in the event of an accident.
Hardware Kit/Mount Parts
Actual appearance may dier from illustration shown here.
ID QTY DESCRIPTION
A 4 M4x12mm Bolt & Lock Washer
B 4 M4x15mm Bolt & Lock Washer
C 4 M5x15mm Bolt & Lock Washer
D 4 M6x15mm Bolt & Lock Washer
E 4 M8x15mm Bolt & Lock Washer
F 4 M5x35mm Bolt & Lock Washer
G 4 M6x35mm Bolt & Lock Washer
H 4 M8x35mm Bolt & Lock Washer
I 4 Square Washer
J 4 M8x50mm Lag Screw
K 4 M10x50mm Wall Anchor
L 4 M8 Lag Screw Washer
M 4 Spacer
Important:
1. This mount is intended for use with displays weighing not more than 165lbs
(75kgs). Use of a heavier display can result in property damage, serious injury
or death.
2. Make sure these instructions are read and completely understood before at-
tempting installation. If you are unsure of any part of this installation, contact a
professional installer for assistance.
3. The wall or mounting surface must be capable of supporting the combined
weight of the mount and the display; otherwise the structure must be reinforced.
4. Safety gear and proper tools must be used. A minimum of two people are
required for this installation. Failure to use safety gear and/or attempting this
installation alone can result in property damage, serious injury, or death.
5. Follow all instructions and recommendations regarding adequate ventilation
and suitable locations for mounting your display. Consult your display’s manual
for more information.
We are not responsible for any personal injury or product damage
due to mishandling, incorrect mounting, incorrect assembly or
incorrect use of this product.
1 2
1
2
A
B
C
D
E
F
G
H
I J
L
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualied contractor. If the hardware you require is not included please contact your local
hardware store.
M
K
13mm Socket Wrench
Included in Hardware Kit
for Lag Screw installation.
Built-in
Bubble
Level
3
ID QTY DESCRIPTION
11 Wall Mount
21 Left Bracket
31 Right Bracket
Left (L) and
Right (R) top rail
Locking Caps
Rotating
Locking Bar

3 4
Step 2: Install the Wall Mount (1) to the Wall
After determining the height of the wall mount and composition of your walls, use the
following installation instructions to install the wall mount to your wall – wood stud
frame, or concrete/masonry.
Wood Stud Walls:
A. Use a high quality stud nder to
locate two vertical studs nearest
where you want to install your
mount. Mark the edges of the studs
and then identify the exact stud
centers (Fig 1).
Step 3: Attach the Brackets to the Display
Important:
Use extra care during this portion of the installation. Avoid setting your display face
down if possible as it may damage the viewing surface. Protect the display surface
with a towel or blanket
Important:
Do not drill into mortar joints! Be sure to mount in solid parts at least 1" (25mm) from
the mortar lines. It is recommended to use a standard electric drill on slow to avoid
block breakage.
Fig. 3
Concrete or Masonry Wall:
A. For an accurate installation, make sure the included bubble level is at room
temperature to allow for the bubble to move freely. Place the Wall Mount (1) against
the wall in the desired location and height determined in Step 1. Level it using the
included bubble level.
B. With the help of another person, mark the holes with a pencil for securing the
mount and set the assembly aside.
C. Drill a 2" deep hole at each of the marked locations using a 10mm (3/8") masonry
bit. Remove any excess dust from the holes.
D. Insert one Anchor (K) into each hole so that it is ush with the concrete surface. A
hammer can be used to lightly tap the anchors into place if necessary.
E. With help, hold the Wall Mount back into position with the slots over the pilot holes.
Check again that it’s level. Use your socket wrench to install the Mount with the lag
screws and washers . Do not over-tighten these screws.
Fig. 4
A. Examine the back of your display. Consult your display’s manual or carefully test
the M4, M5, M6 or M8 bolts to nd the right diameter and length for your display’s
VESA mounting holes. For the correct diameter and length, you should not need to
force the bolts. If you feel any resistance, stop immediately to avoid damaging your
display and its internal components.
- If the back of your display is at and the mounting holes are ush with the surface,
you will use the shorter (12mm or 15mm) M4, M5, M6 or M8 bolts (Fig. 5a) from
the hardware kit.
Left
edge
of stud
Right
edge
of stud
Center
of stud
Fig. 1
Fig. 2
Important:
This mount must be secured to two
adjacent 2" x 4" vertical wood studs
no more than 16" apart. These studs
must be capable of supporting the
combined weight of the mount and
the display.
16"
B. For an accurate installation, make
sure the included bubble level is at
room temperature to allow for the
bubble to move freely. Based on
your edge and center marks, hold the
Wall Mount (1) at the desired height
as determined in Step 1. With the
help of another person, align the wall
plate slots over your left and right
stud marks and level the Mount with
the integrated bubble level. With a
pencil, mark your drilling holes in the
center of each stud through the top
and bottom plate slots in the left,
and right studs (Fig 2). Set the Mount
aside.
E. Drill a pilot hole at each marked
location using an electric or
portable drill with a 5mm (3/16") bit.
F. With help, hold the Wall Mount back
into position with the slots over
the pilot holes. Check again that
it’s level. Use your socket wrench to
install the Mount with the lag screws
and washers (Fig. 3). Do not over-
tighten these screws.
J L
Use the M8x50mm Lag Screws (J) and corresponding
Washers (L) to intall the Wall Mount (1) to the studs.
You will need to use the included Socket Wrench or
your own socket wrench with 13mm socket.
Note: If the concrete wall
is covered by a layer of
plaster or drywall. The
wall anchor must pass
completely through the
layer to rest ush with the
concrete surface (Fig. 4).

Fig. 5a Use the 12mm or 15mm M4,
M5, M6 or M8 bolts, lock
washers and square washers
for mounting brackets to
display WITHOUT spacers
Use the 35mm M5, M6 or
M8 bolts lock washers and
washers for mounting brackets
to display WITH spacers. Use
ONLY with curved or recessed
display backs or those backs
with protrusions
Fig. 5b
- If the back of your display is curved or has
a protrusion, or if the mounting holes are
recessed, you will need to use the enclosed
Spacers (M) with the longer (35mm) M5, M6
or M8 bolts (Fig. 5b) from the hardware kit.
B. Make sure that the Brackets (2 & 3) are facing up.
Examine the two brackets. When installed to the
back of your display, the large tightening knobs
should point to the outside of your display (Fig.
6a). The hooks should be positioned to grab the
rails from the top down (Fig. 6b).
Important:
Never force bolts into display as damage
may occur and NEVER use an electric drill
to secure the bolts.
5 6
Fig.7a
Mounting Brackets to a at-back display
Use the 12mm or 15mm M4, M5, M6 or M8 bolts, lock
washers and square washers for mounting plate to
display WITHOUT spacers
Mounting Brackets to a curved back display
or display with recessed holes or protrusions
Fig. 7b
Use the 35mm M5, M6 or M8 bolts lock washers and washers for
mounting plate to display WITH spacers. Use ONLY with curved
or recessed display backs or those backs with protrusions
Fig. 6b
Bracket View Facing the
BACK of your Display
2
3
Fig. 6a
View
of Left
Bracket
View
of Left
Bracket
Use your selected bolts, lock washers, square
washers and spacers if needed (Fig. 7a and 7b)
to attach the Brackets to the back of your display
using your phillips head screwdriver.
Once installed to the display, both brackets
should be of equal heights and level to each
other. Make sure all of the bolts are snug, but
do not over tighten!

7
Step 4: Hang the Display
A. Check that the top Rotating Locking Bar
is ipped up all of the way so that the top
rails have clearance for the brackets to
engage (Fig. 8).
Important:
You will need the assistance
of another person to lift your
display.
Fig. 8 Fig. 9
8
Note: Once in place, the lateral position of the
display can be adjusted by rmly grabbing both
sides of the display and carefully sliding it along
the rails.
D. Take your left and right Locking Caps and
slide them over the Rotating Locking Bar on
each side until they are snug against each
Bracket to secure (Figs. 10 and 11).
Step 5: Adjusting the Display
For up and down tilt, hold the installed display rmly at the top and bottom and gently
tilt the display up and down until you have reached your desired viewing angle. Make
sure that the Rotating Locking Bar is down and secured by the Locking Caps. The knobs
in the middle of the outside of the brackets can be tightened to secure the display.
Display Removal
Should you need to remove your display from the wall mount, slide the Left and Right
Locking Caps o from the top rail Locking Bar.
Have another person hold your display while you ip the Rotating Locking Bar up. With
your assistant, carefully lift the display o from the rails.
B. Make sure that the knobs on the side of the installed brackets have been tightened
to keep the display steady throughout installation.
B With assistance, lift the bracket-mounted display over the wall mount and then
hook the brackets over the top and bottom rails. You may need to slightly lift and
rotate the bracketed display to engage both top and bottom hooks with the rails.
Make sure that
both top and
bottom rails are
fully engaged
with all four
hooks before
releasing the
display.
C. After the display is
in position, ip the
Rotation Locking
Bar down so that
it is overlapping
each hook on top
(Fig. 9).
Fig. 10
Note: Slide the
Locking Caps all the
way to meet the Left
and Right Brackets
on the top rail. The “L”
and “R” on the caps.
should be facing
front when installed.
Fig. 11

Failure to follow these installation instructions or any other abuse,
mistreatment, unreasonable use or neglect of the product shall
constitute a waiver of all warranties, expressed and implied, and constitute a
waiver of all claims of liability against IPSG, its directors, ocers, shareholders,
parents, subsidiaries, aliates, agents, customers and licensors, for any direct,
indirect, special (including loss of revenue or income, pain and suering,
emotional distress, or similar damages), incidental, punitive, or consequential
damages arising out of or resulting from the improper installation, abuse,
mistreatment, unreasonable use or neglect regardless of whether such
damages arise in contract, tort, under statute, in equity, at law, or otherwise.
9