INNO Instrument V20 User manual
V20
Please read this manual before operating the device.
Please keep this manual together with the device.
2017/11 Rev.1.4
Fiber
Microscope
2
V20
User Manual
3
Important: INNO Instrument strongly recommends all users to read this manual
before operating the V20.
This manual is valid for the following software version:
4
Contents
Fiber microscope
Importance of a cleaning the connector end interface
Operation
Patchcord Tip Adapters
Convenient test with PC software
Test report
Specications
Maintenance and technical support
7
8
9
10
11
12
13
14
5
Fiber microscope
Handheld ber microscope enables ber face inspection
Available in 200(μm) x or 360(μm) x magnication
With this tool, the process of ber testing can be simplied and performed quickly.
Accurate test results can be generated to demonstrate successful pass.
•Test report
•S/W program to use with PC
•Pass/Fail Result
•Image magnication
6
Importance of a cleaning the connector end interface
It is essential to utilize auto-analysis software to test the connector and assess its
quality during the commissioning and installation of the ber. It is important to save
the verication records of the connector for future reference. The end-to-end
verication can be achieved by combining the connector test with the ber
verication. The following are the displayed test images.
It can also analyze and report data through the corresponding software, as shown
in the following picture:
Passed Failed
7
Operation
Fiber interface: Connect the ber connector to V20 after
unscrewing the cap of V20.
USB interface: It is used for connecting to PC and other
corresponding instrument.
Rotary knob for adjusting focus: It is used for focusing to make
the image clear. In order to enable the fuction of V20, you just
need to connect the V20 with the ber connector to the
instrument or to the PC which is able to communicate with upper
computer. After making the image of the ber, it will become clear
by adjusting the rotary knob for focus, allowing you to analyze the
image.
8
Patchcord Tip Adapters
2.5mm / APC 2.5mm / UPC
Universal patchcord tip
for 2.5 mm ferrules(APC)
Universal patchcord
tip for 2.5 mm ferrules(UPC)
1.25mm / APC 1.25mm / UPC
Universal patchcord tip
for 1.25 mm ferrules(APC)
Universal patchcord tip
for 1.25 mm ferrules(UPC)
9
Convenient test with PC software
The result of INNO software can be analyzed through the following step:
connecting the optical ber to the device, adjusting the sharpness and then
tapping “screenshot”.
Meanwhile, the data can be analyzed in detail.
The corresponding test task can be marked under the identication function.
10
Test report
11
Specications
Parameters
Size 150 x 35 x 34mm
Weight 168g
Resolution 3.2μm
Image sensor 640 x 480 (VGA)
Visual test < 5μm
View angle
200μm*200μm of high magnication
360μm*360μm of low magnication
Light source Blue LED
Digital zoom 3 grades
Connector USB 2.0
Operating temperature -10°C to 50°C
Storage temperature -40°C to 70°C
Bulkhead tips 2.5mm (UPC, APC), 1.25mm (UPC, APC)
12
Maintenance and technical support
Any operation, such as alignment, maintenance or repair of the device, can only be
performed by qualied maintenance personnel. Please contact the engineers
of INNO Instrument. You can also consult any queries through the following
website.
www.innoinstrument.com
Tel: +82-32-837-5600
Fax: +82-32-837-5601
Email: [email protected]
Please visit us on Facebook www.facebook.com/innoinstrument
www.innoinstrument.com
Copyright
ⓒ
2017
INNO
Instrument
Inc.
All
rights
reserved.
E-22F,
30,
Songdomirae-ro,
Yeonsu-gu,
Incheon
21990,
Republic
of
Korea
tel
82-32-837-5600
fax
82-32-837-5601
Printed in Korea
Table of contents
