innotool toolset User manual

Page 1
innotool austria Gerätebau GmbH / Oberhub 11/ 6844 Altach / Austria
T [phone] / F [phone] / [e-mail]
toolset
– Instruction Manual
Counter-weight lock screw
use a 4mm hex. wrench
Adjustable guide rail
X – axis fine adjustment
Z – axis lock
X – axis lock
Dual axis indicator head
Precision spindle
Z – axis fine adjustment
LCD Display Keyboard
Turn the knob left or right and the clamping will be loosed

Page 2
innotool austria Gerätebau GmbH / Oberhub 11/ 6844 Altach / Austria
T [phone] / F [phone] / [e-mail]
toolset
– unpack and set up
Take the TOOLSET with the mounted wood board out of the cardboard
and put it to his work place.
Re
move the 3 screws on the bottom of the wood board and put the
TOOLSET away from the board.
Remove the transport screw on the top of the column
under holding
the weight rope
(Important!!!). The weight is transport saved at the
column. After removing the
transport screw put the weight rope
softly to the column.
Loose the Z-
Clamp and move up with the measuring wagon. Now take
away the indicator pad.
Caution:
If the Optic is not mounted and the transport screw is
already loosed it is possible that the
measuring wagon move
automatically up because of the heavier Optic weight. That could result
in damage of the system.
OPTION OPTIC:
Stick the Optic with the distance tube on the Optic holder and tight
the clamp screw a little. Adjust the Optic on the z-
axis with a test bar
and fix the clamp screw.
PACKAGING:
Please use the original transport elements if you have to send the TOOLSET back to the
supplier (for maintenance). Transportation elements are: transportation cardboard, wood
board with the three screws and the plastic elements, Indicator pad.

Page 3
innotool austria Gerätebau GmbH / Oberhub 11/ 6844 Altach / Austria
T [phone] / F [phone] / [e-mail]
toolset
– Documentation
TOOLSET initial steps and operating instructions.
Set up:
The instrument should be shipped upright only and inspected after unpacking for any damage in
transit. To remove the shipping base, it is best to slide just one edge of the base at a time over
the table end so as to undo the screw at that point.
The unit should be installed on a stable support in an environment that is as dust-free as
possible and near a 220 V plug (line voltage adapter).
Strong electrical interference fields (high-power engines, welding equipment and the liks) are to
be avoided.
The counter-weight is to be fastened with a screw used to anchor the unit during transit. Do not
slide the measuring carriage before removing the screw and cleaning the guide rails of any
packaging debris.
Adjustment and locking:
Coarse adjustment for both axes is carried out by turning the control grips on the measuring
carriage to the right or left. Locking of the axes is carried out in the mid-position of the control
grips (fine adjustment function). Do not turn out the control grips completely.
Diameter fine adjustment is carried out by turn in the control button on the front face.
Vertical fine adjustment is carried out using the hand wheel on the instrument foot at the side.
Precision bearing:
The bearing and the receiving cone are to be cleaned before a tool is inserted. The precision
bearing has a test collar with reference diameter and height for scale calibration (R 44.45mm/R
1.750inch engraved in the hand wheel)
Electronics:
When the unit is first placed in service, it is important to check the bearing reference. This is
carried out following the reference start up in the measuring mode for measuring the calibration
edges.
Reference correction is possible in the set menu. The main menu is reached using the procedure
described (depress Set about 3 seconds immediately after ESC). Select the TOOLSET reference
in the main menu (depress number 1) which brings up the reference menu.
This procedure is described the reference menu.