Innovative Technology ITNS-500 User manual

Quick Installation Guide
innovative technology
ITNS-500

-1-
Note
This film scanner supports Windows XP, Vista and Windows7(32/64bits) via
USB 2.0 only.
We strongly suggest using a clean, dry, non-alcohol cotton swab to clean the glass
surface on the back-light holder and the business card fixture periodically to
produce a clear image.
Make sure all negative films, slide films, cover trays and photos are free of dust
and dirt before inserting into the ITNS-500 as this may affect the image quality
when scanning.
When cleaning films, please use a professionally recommended purger from a
photo store to avoid damaging old or precious films.
I. Unpack the ITNS-500
ITNS-500
User Manual
innovative technology
ITNS-500
User Manual
Backlight Holder
Photo/Business Card Holder
innovative technology
ITNS-500
Quick Installation Guide
Quick Installation Guide
Business card Fixture

-2-
III. Using the ITNS-500
Power status LED
Copy button
Photo/Business
Card slot
Film/Slide
slot
Slot for Backlight
holder
USB Port
After completing the installation, the film-scanner is ready to start
with “ Image scan Tool” under program files.
(WindowsXP/Vista/Windows7) It is recommended (but not
required) to restart your PC after installation or un-installation.

Installing film into the film holder
Install slide Film into the holder entitled “Slides Only”
1. Open the slide holder as illustrated
2. Place slide in recessed slot in holder 3. Close the film holder
-3-

Install Negative Film into the holder entitled “Negative Film Only”:
1. Open the film holder as illustrated
2. Install film into negative film slot 3. Close the film holder
-4-

Note
To avoid a mirror image, follow the serial numbers (from left to right) on
top of film when installing negative film into holder.
Figure 1
If the image is upside down [see fig.2], the image can be corrected by
”Rotate” function in Image Scan Tool after capture [see fig.3].
Figure 2
Figure 3
-5-

II. Driver Installation
1. Turn on the computer
2. Insert the installation CD into the CD-ROM drive and the installation CD
menu will appear
3. Click the “Installation” button to begin.
4. After the installation completed, you can browse the video instructions
and user manual from the CD.
5. Click ''Exit'' to quit the driver installation menu.
To use the ITNS-500, please complete the following installation in advance.
-6-
scanner Installation

How to use ITNS-500
1. Put Film into film holder
2. Insert the film/slide backlight holder at the rear side of the ITNS-500 unit.
-7-
Scanning Film/Slide
3. Plug in your USB cable to your PC with another side on the ITNS-500 unit.

-8-
4. Insert the film holder into the right side of the ITNS-500 unit
5. Click “Image Scan Tool” PC program to enter operation interface as
shown below. The PC program will go into Film/Slide Mode
automatically.

Scanning Photo
1. Remove the film / slide holder as well as the back-light holder from the
ITNS-500 unit if either one is attached.
Remove film /slide holder by sliding
the holder to the left hand side.
Remove back-light holder by pressing
down the handle and pulling it out.
2.Open the photo holder as illustrated, place the photo on the base of the
photo holder and close the photo holder.
-9-

4. Insert the photo holder into the photo slot of the ITNS-500 unit.
-10-
5. Click “Image Scan Tool” PC program to enter operation interface as
shown below. The program will go into Picture Mode automatically.

-11-
Scanning Business Card
1. Follow Step 1 to remove Film/Slide holder as well as back-light holder in
the previous pages.
2.Close the photo holder and Place the business card on the base of the
photo holder following the engraved guide line on the holder.
3.Put the Business Card fixture on the top of Photo Holder.
4.Insert the entire photo holder with the business card fixture into the
photo slot of the ITNS-500 unit.

-12-
5. Press “Copy” button or press “Snap Shot” button in the PC program to capture
the image
6. Process necessary modification by using the function buttons on right
hand side

-13-
7. Save captured images to PC
8. Get final images from PC for further review and edit

-14-
V. Cleaning the ITNS-500
Detach the backlight holder from the ITNS-500 unit.
Using the provided clean brush or a clean, dry,
nonalcohol cotton swab to clean the glass surface
periodically to produce a clear image during operation.
Cleaning the backlight holder
Cleaning the business card fixture
Using the provided clean brush or a clean, dry,
non-alcohol cotton swab to clean the surface
of the business card holder periodically to
produce a clear image during operation.
You can double check the result of cleaning
by removing the film holder from the
device and insert the cleaned back-light
holder back into the unit. When you
haven't noticed any dust in the live view
window that means you can stop cleaning.
Caution
The backlight holder should be handled with extra care to avoid any
scratching the glass surface in order to maintain the quality of scanned
image.
Note: If there's any abnormal condition cause user special behaviour, Combo Scanner can be
reset by pull/insert USB cable again.

1 Channel Drive

Instructions shall caution users that modifications not approved by the party responsible
for compliance could void user's authority to operate the equipment.
The following or equivalent as appropriate:
“NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.”
Statement that the product complies with Part 15 (i.e. “This device complies with Part 15
of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.”)
WARNING : This product contains chemicals known to the State of California to cause
birth defects or other reproductive harm. For more information on these regulations and
a list of chemicals, log on the following website address:
http://www.oehha.ca.gov/prop65.html
●
●
●
●
CALIFORNIA PROP 65 WARNING

Revision: 1.0_2