Innovative Technology ITNS-500 User manual

Quick Start Guide
innovativetechnology
ITNS-500

-1-
Note
This film scanner supports Windows XP, Vista, Windows 7 and Windows 8
(32/64bits) Mac OS 10.7.5 /10.8.4 via USB 2.0 only.
We strongly suggest using a clean, dry, non-alcohol coon swab to clean the glass
surface on the backlight holder and the business card fixture periodically to
produce a clear image.
Make sure all negave films, slide films, cover trays and photos are free of dust
and dirt before inserng into the ITNS-500 as this may affect the image quality
when scanning.
When cleaning films, please use a professionally recommended purger from a
photo store to avoid damaging old or precious films.
Unpacking theITNS-500
ITNS-500
User Manual
innovativetechnology
ITNS-500
User Manual
Backlight Holder
Photo/Business Card Holder
innovativetechnology
ITNS-500
Quick Installation Guide
Quick Installation Guide
Business card Fixture

Software Installation
To use the ITNS-500, please complete the following installaon in advance.
Windows Installaon
1. Turn on the computer.
2. Insert the installaon CD into the CD-ROM drive and the installaon
CD menu will appear. Click the “Installaon” buon to begin.
4. Aer the installaon completes, you can browse the video instrucons
and user manual from the CD.
5. Click ''Exit'' to quit the driver installaon menu.
6. Aer compleng the installaon, the film-scanner is ready to use with
“Image Scan Tool” under program files. Remark: If you are using Win XP
64 or Vista 32/64, you may also need to run "Launch vcredist_x86.exe" as
the Microso Visual C++ 2010 Redistributable Package is necessary for this
installaon. It is recommended (but not required) to restart your PC aer
installaon or un-installaon.
-2-
ITNS-500 Negative/Slide Scanner

-3-
Mac Installaon
1. Turn on Mac computer.
2. Insert the installaon CD into the CD/DVD drive.
3. Copy “ImageScanTool.mpkg” to your computer and double-click it. If
you are using a 10.7 operang system, copy the 10.7.5 file. If you are
using a 10.8 operang system, copy the 10.8.4 file.
4. Click Connue to install “ImageScanTool” and follow the on-screen
instrucons.
5. Once the installaon completes, click Close.

-4-
Using the ITNS-500
Power status LED
Copy buon
Photo/Business
Card slot
Film/Slide
slot
Slot for Backlight
holder
USB Port

-5-
Note
To avoid a mirror image, follow the serial numbers (from leto right)
on top of film when installing negave film into holder.
Figure 1
If the image is upside down [see fig. 2], the image can be corrected with
the ”Rotate” funcon in the Image Scan Tool aer capture [see fig. 3].
Figure 2
Figure 3

-6-
How to use ITNS-500
1. Put Film into film holder
2. Insert the film/slide backlight holder at the rear side of the ITNS-500 unit.
ScanningFilm/Slide
3. Plug the USB end of the supplied cable into your PC/Mac and the other
end into the ITNS-500 unit.

-7-
4. Insert the film holder into the right side of the ITNS-500 unit.
PC Mac
5. Open the “Image Scan Tool” program to enter the operaon interface
as shown below. The program will go into Film/Slide Mode automacally.

-8-
Scanning Photos
1. Remove the film/slide holder, as well as the backlight holder, from the
ITNS-500 unit if either one is aached.
Remove film/slide holder by sliding
the holder to the le hand side.
Remove backlight holder by pressing
down the handle and pulling it out.
2. Open the photo holder as illustrated. Place the photo on the base of the
photo holder and close the photo holder.

-9-
3. Insert the photo holder into the photo slot of the ITNS-500 unit.
4. Open the “ImageScanTool” program to enter the operaon interface
as shown below. The program will go into Picture Mode automacally.
PC Mac

-10-
Scanning Business Cards
1. Follow Step 1 from “Scanning Photos” to remove Film/Slide holder as well
as the backlight holder.
2. Close the photo holder and place the business card on the base of the
photo holder according to the engraved guideline on the holder.
3. Put the Business Card fixture on top of the Photo Holder.
4. Insert the enre photo holder, with the business card fixture, into the
photo slot on the ITNS-500 unit, and select "Business Card" mode in the
"Image ScanTool".

-11-
5. Press the “Copy” buon or click the “Snap Shot” buon in the Image
Scan Tool program to capture the image.
6. Make any necessary adjustments to the scanned image using the funcon
buons on right hand side of the Image Scan Tool program.
PC Mac

-12-
7. Save captured images to your computer.
8. Get final images from PC/Mac for further review and edit.
PC Mac

Revision: 1.0_8