Innovative WINSTON WORKSTATION User manual

800.524.2744 www.LCDarms.com
INSTALLATION INSTRUCTIONS
STEP 1 | COLUMN ..............................................................................................................Page 3
STEP 2 | MOUNTS
Freestanding Base .............................................................................................................................................Page 4
Clamp Mount ...........................................................................................................................................................Page 5
Thru Mount ................................................................................................................................................................Page 6
STEP 3 | WORK SURFACE ...........................................................................Page 7
STEP 4 | CABLE MANAGEMENT...................................................Page 10
WINSTON WORKSTATION®
for Apple iMac
© 2015 Innovative Office Products, LLC P511767 REV B
NOTE: Depending on your Winston Workstation®configuration,
you may not receive all the parts shown within this instruction booklet.
Installation may require two people.
2
3
4
1
PAGE 1 OF 11

800.524.2744 www.LCDarms.com
A Work Surface
411 4 6 9
B Column
411 47 0 - M
C 7/32" Allen Wrench
701127
D Felt Pad
111 4 6 4
E Freestanding Base
1117 31
F Cable Retainer
11173 5
G 3/8-16 x 1" FHSCS
7 0112 4
H Large “L”
111311
I 1/4-20 x 1/2" PhPHS
700435
J Small “L”
111312
K Spacer
701544
L 1/2-13 x 3" Set Screw
701126
M Thru Mount Base Plate
11 0 9 78
N 1/4-20 x 2-1/2" Hex Head Bolt
711570
O Thru Mount Washer
711572
P Thru Mount Nut
711571
Q 1/8" Allen Wrench
701312
R 10-32 x 1" FHSCS
711 4 6 7
S Column Cap
111 0 4 0
T Shelf Bracket
1116 0 4 -1 24
U Enclosure
1116 0 3 -1 24
V #6 x 3/4" FHPhS
711 8 8 0
W Shelf
1116 2 9 -1 24
X Cover
1116 0 5 -2 4 8
Y Column Cap
1112 7 5 - 70 8
Z Column Cable Clip
111 2 0 3 -7 0 8
PARTS LIST* WINSTON WORKSTATION®
for Apple iMac
* Depending on your Winston Workstation® conguration,
you may not receive all parts shown above.
PAGE 2 OF 11

800.524.2744 www.LCDarms.com
COLUMNSTEP 1
i
1 2 3
A
B
Use 7/32" Allen wrench to
press cable firmly into place.
Confirm cable is
properly seated
into position.
C
IMPORTANT: Do not pull excessively
on cable – doing so may result in
accidental actuation of column.
PAGE 3 OF 11

800.524.2744 www.LCDarms.com
FREESTANDING BASE | MOUNTSSTEP 2
1 2 3
4 5
E
D
G
Hang base plate over edge of
work surface to allow access
to countersunk holes. Side
of base plate with felt pads
should be face down.
Place work surface
on base plate to aid as a
counterbalance.
Note the orientation of
column cable exit and
base plate – cable should
exit in direction as shown.
7/3 2 "
F
PAGE 4 OF 11

800.524.2744 www.LCDarms.com
CLAMP MOUNT | MOUNTSSTEP 2
1 2 3
7/3 2 "
7/3 2 "
HF
I
J
L
K
G
A
B
Note the orientation of
column cable exit and
mount – cable should exit
in direction as shown.
PAGE 5 OF 11

800.524.2744 www.LCDarms.com
THRU MOUNT | MOUNTS
* The supplied mounting hardware may need to change depending upon mounting substrate.
STEP 2
1 2
*
7/3 2 "
E
M
F
N
O
P
A
B
*
Note the orientation of
column cable exit and
mount – cable should exit
in direction as shown.
PAGE 6 OF 11

800.524.2744 www.LCDarms.com
WORK SURFACE
1
1/8"
R
Q
S
1
3
2
4
IMPORTANT: Tighten bolts evenly.
Work surface clamp should sit flush
against the column, ensure there
are no gaps. Also, it is important the
work surface clamp is level.
i
STEP 3
Two people may be required to
install work surface to column.
One to hold the work surface
and the second person to secure
the column clamp.
PAGE 7 OF 11

800.524.2744 www.LCDarms.com
WORK SURFACE
2 3
STEP 3
Place the platform base on the work
surface. Align the platform tabs at the
back of the work surface as shown.
V
U
T
PAGE 8 OF 11

800.524.2744 www.LCDarms.com
WORK SURFACE
4
STEP 3
OROR
Choose from three
height settings
for your iMac.
Note: In the lowest
height setting,
the shelf (item V)
is not used.
5 6
W
X
W
Y
PAGE 9 OF 11

800.524.2744 www.LCDarms.com
CABLE MANAGEMENTSTEP 4
Z
PAGE 10 OF 11

800.524.2744 www.LCDarms.com
Press button and hold. Lift up/down. Release to lock in place.
HEIGHT ADJUSTMENT
iIs your height adjust button not working?
If so, make the adjustments below.
Slide workstation so that
the work surface hangs over
desk edge to allow access to
underneath the work surface.
Loosen the two screws
as shown.
Slide bracket in the direction
shown and tighten screws.
Test height adjust button –
readjust by repeating the steps
above as necessary.
1
2
3
4
PAG E 11 OF 11