Innovative WNST-1 User manual

800.524.2744 InnovativeWorkspaces.com
STEP 1 | COLUMN...................................................................................................................Page 3
STEP 2 | MOUNT.........................................................................................................................Page 4
STEP 3 | WORK SURFACE...............................................................................Page 5
STEP 4 | BEAM................................................................................................................................Page 6
STEP 5 | MONITOR TILTER..............................................................................Page 7
STEP 6 | MONITOR CUPS..................................................................................Page 8
STEP 7 | CABLE MANAGEMENT.....................................................Page 9
3
4
7
1
2
5
6
NOTE: Depending on your Winston Workstation®configuration,
you may not receive all the parts shown within this instruction booklet.
Installation may require two people.
© 2018 Innovative Office Products, LLC P512242 REV D
WNST-1 & WNST-2
Winston Workstation® Single & Dual | Installation Instructions
PAGE 1 OF 10

800.524.2744 InnovativeWorkspaces.com
A Work Surface
1114 3 5
B Column
411470
C Felt Pad
1114 6 4
D Freestanding Base (WNST-1 only)
1117 31
E Freestanding Base (WNST-2 only)
111 24 8
F Cable Retainer
111 73 5
G 3/8-16 x 1" FHSCS
701124
H Screws
713273
I Top Plate
111 73 6
J Utility Tray
11 3 0 2 5
K 10-32 x 1" FHSCS
7114 6 7
L Beam (10" or 30")
412036 or 412 037
M Column Clamp
111 0 4 0
N 1/8" Allen Wrench
701312
O 7/32" Allen Wrench
70112 7
P Column Cap
1112 7 5 -7 0 8
Q 10-32 x 3/8" PhPHS
702281
R 75/100 mm VESA Adapter
105587
S Standard Monitor Tilter
405397
T HD Monitor Tilter (optional)
407747
U M4 x 12mm PhPHS
702096
V Fine Tune Adjust (optional)
8473
W Dog Washer
1112 3 0 - 6 0 3
X 10-32 x 1/2" FHSCS
7 112 4 0
Y Column Cable Clip
1112 0 3 - 70 8
WNST-1 & WNST-2
Winston Workstation® Single & Dual | Parts List
Depending on your Winston Workstation® conguration,
you may not receive all parts shown below.
PAGE 2 OF 10

800.524.2744 InnovativeWorkspaces.com
COLUMNSTEP 1
i
1 2 3
A
B
Use 7/32" Allen wrench to
press cable firmly into place.
Confirm cable is
properly seated
into position.
O
IMPORTANT: Do not pull excessively
on cable – doing so may result in
accidental actuation of column.
CAUTION: Do not press height adjust
button until unit is fully assembled.
PAGE 3 OF 10

800.524.2744 InnovativeWorkspaces.com
FREESTANDING MOUNT
1 2 3
4 5
D or E
C
STEP 2
Hang base plate over edge of
work surface to allow access
to countersunk holes. Side
of base plate with felt pads
should be face down.
Place work surface
on base plate to aid as a
counterbalance.
G
7/32 "
F
PAGE 4 OF 10

800.524.2744 InnovativeWorkspaces.com
WORK SURFACE
1 2
J
STEP 3
Slide utility tray onto work surface.
Utility tray simply rests on top of
work surface.
I
H
PAGE 5 OF 10

800.524.2744 InnovativeWorkspaces.com
1
3
2
4
1/8"
1/8"
BEAM
M
K
L
1
3 4
2
P
STEP 4
IMPORTANT:
Tighten bolts evenly.
The beam should sit flush
against the column, ensure
there are no gaps. Also, it is
important the work surface
clamp is level.
i
N
PAGE 6 OF 10

800.524.2744 InnovativeWorkspaces.com
MONITOR TILTER
STANDARD TILTER & SPRING TILTER
FINE TUNE HEIGHT ADJUST TILTER
Q
Q
Q
R
S or T
U
Q
V
S or T
R
U
1
1 2 3 4
2
STEP 5
PAGE 7 OF 10

800.524.2744 InnovativeWorkspaces.com
i
MONITOR CUPS
1
7/32 "
STEP 6
1/8"
W
X
PAGE 8 OF 10

800.524.2744 InnovativeWorkspaces.com
CABLE MANAGEMENTSTEP 7
1
Y
PAGE 9 OF 10

800.524.2744 InnovativeWorkspaces.com
HEIGHT ADJUSTMENT
iIs your height adjust button not working?
If so, make the adjustments below.
Slide workstation so that
the work surface hangs over
desk edge to allow access to
underneath the work surface.
Loosen the two screws
as shown.
Slide bracket in the direction
shown and tighten screws.
Test height adjust button
– readjust by repeating the
steps above as necessary.
1
2
3
4
Press button and hold. Lift up/down. Release to lock in place.
PAGE 10 OF 10