INPRO 1100/G2 User manual

IPC.329/REV.8
Important
1. Acclimate materials 24 hrs
before installation. Maintain
temperature controlled
environment after installation
2. Install in accordance with
manufacturer’s installation
instructions. Failure to do so
will void the warranty.
Installation tips
1. Cut covers up to 1/16” (1.6mm)
longer to ensure a tight  t.
2. Lubricate blades when cutting
aluminum to reduce burrs.
SECTION VIEW
Safety Glasses, Tape Measure, 3/8” socket for machine screw hex bolt, 7/16” socket for wood screw
hex bolt Level, Power Drill, Drill Bits - 1/4” masonry (concrete/concrete block), Power Miter Saw, 1O”
Blade with 60-80 Carbide Tipped Teeth
Recommended tools
1/4 - 20 x 5" Hex
Head Screw W/
Phillips Head Slot
Mounting
Bracket
Cont. Alum.
Retainer
.080" (2mm)
5 5/16"
[135mm]
2 11/16"
[69mm]
3 3/4"
[95mm]
1 1/2"
[38mm]
1 1/2"
[38mm]
Diameter
Vinyl Cover
.080" (2mm)
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails

Components and fasteners
1100A
CONTINUOUS
ALUMINUM RETAINER
801
MOUNTING
BRACKET
1100V
VINYL
COVER
1102
LEFT RETURN
1103
RIGHT RETURN
1104
OUTSIDE CORNER
804-910-SPL
SPLICE
1/4"
LOCK WASHER
SPRING REGULAR
1/4" - 20
FLANGED SCREW
HEX NUT
1/4" - 20
HEX WASHER
SCREW
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails

Layout view
DISTANCE TO BE
DETERMINED BY
INSTALLER (TYP)
DISTANCE TO
BE DETERMINED
BY INSTALLER
OUTSIDE CORNER
MAX FIRST
BRACKET LOCATION
FROM WALL
SPLICE
RETURN
DISTANCE TO
BE DETERMINED
BY INSTALLER
1 1/2"
[38.1mm]
4"
[102mm]
RETURN
MAX BRACKETS
ON CENTER 4"
[102mm]
4"
[102mm]
4"
[102mm]
32"
[812.8mm]
FIELD DIMENSIONS
(TYPICAL ALL WALLS)
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails

Exploded view assembly
804-910-SPL
SPLICE
1/4"-20 FLANGE
NUT
1/4-20 LOCK
WASHER
1/4-20X5"
PHILLIPS HEX HEAD
TOGGLE BOLT 1100V
VINYL COVER
1100A
CONTINUOUS
ALUMINIM
RETAINER
1103
RIGHT RETURN
1102
LEFT RETURN
801
MOUNTING
BRACKET
1/4"-20 X 1"
SERATED FLANGE
HEX BOLT
1/4" TOGGLE
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails

FIG. 1
FIG. 2
2. Drill holes in centerline of aluminum retainer for
brackets, returns, corners and splices using /4" (6mm)
drill bit. Position aluminum retainer against wall at
desired height allowing for returns and corners. Level
and mark bracket holes on wall. Drill marked holes
with 3/4" (19mm) drill bit for toggle bolts (drywall
installation) or 1/2" (13mm) drill bit for lead anchor
(concrete wall installation). See Figure 2.
Please read all instructions before installing handrail.
1. Cut aluminum retainer to desired length, leaving
allowance for returns and outside corners.
See Figure 1.
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails

FIG. 3
FIG. 4
3. Attach returns and corners to retainer leaving a
1/16" (1.5mm) gap between returns/corners and
retainer to allow for adjustment. Loosely attach
brackets to retainer. Mount on wall, level retainer
and tighten screws to secure. See Figure 3.
3a. For long runs of handrail, secure each section of
aluminum retainer to the next with the supplied
splice piece.
NOTE: Make sure you install the splice with side
"A" facing out.
4. Cut vinyl cover to length between returns and/or
corners. (Note: Trim factory edges square before
installation). Position cover on retainer and
adjust returns and/or corners for a tight fit. Snap
cover on retainer by starting at top and pivoting
over the bottom of retainer. See Figure 4.
Please read all instructions
before installing handrail.
Installation Instructions
1100/G2-1100 Handrails