INPRO 51SS User manual

Please read all instructions before installing
wallguard.
51SS WALL GUARD
56SSF WALL GUARD
NOTE:The 51SS and the 56SSF
Stainless Steel Wall Guards
are manufactured to lengths
specified by the customer.
Installation Instructions
51SS and 56SSF Stainless Steel Wall Guards
Safety Glasses, Tape Measure, Level, Power Drill, Drill Bits - 1/4”masonry (concrete/concrete block), Power
Miter Saw, 1O” Blade with 60-80 Carbide Tipped Teeth
Recommended tools
Important
1. Acclimate materials 24 hrs
before installation. Maintain
temperature controlled
environment after installation
2. Install in accordance with
manufacturer’s installation
instructions. Failure to do so
will void the warranty.
Installation tips
1. Cut covers up to 1/16”(1.6mm)
longer to ensure a tight t.
2. Lubricate blades when cutting
aluminum to reduce burrs.
Section View
ALUMINUM
WALL
GUARD
BRACKET
1/4-20 x 6"
SLOTTED FLAT
HEAD BOLT AND
TOGGLE WING
STAINLESS STEEL
WALL GUARD
NEOPRENE GASKET
6"
[152mm]
4"
[102mm]
3 3/8"
[86mm]
1/16"
[2mm] 1/4"
[6mm]
IPC.481/REV.4

Please read all instructions before installing
wallguard.
51SS Wall Guard Components
51SSBAR - Wall Guard
51SSRR - Right Return
51SSLR - Left Return
51SSOC - Outside Corner
51SSIC - Insdie Corner
51SSBK-M - Bracket
51SSGA - Gasket
56SSF Wall Guard Components
56SSFBAR - Wall Guard
56SSFRR - Right Return
56SSFLR - Left Return
56SSFOC - Outside Corner
56SSFIC - Insdie Corner
51SSBK-M - Bracket
51SSGA - Gasket
Installation Instructions
51SS and 56SSF Stainless Steel Wall Guards
Components and fasteners
Wall Condition Specied Fasteners Inpro Part #
Drywall 1/4"-20 x 6" Flat Head Screw, Toggle Wing and Gasket 51SSBK-D
Wood #14 x 6 Phillips Flat Head Wood Screw and Gasket 51SSBK-W

Please read all instructions before installing
wallguard.
Installation Instructions
51SS and 56SSF Stainless Steel Wall Guards
FIELD
DIMENSIONS
(TYPICAL
ALL WALLS)
3 3/8"
[86mm]
32"
[686mm]
MAX O.C.
DISTANCE TO BE
DETERMINED BY
INSTALLER (TYP)
DISTANCE TO BE
DETERMINED BY
INSTALLER (TYP)
Layout Views

Please read all instructions before installing
wallguard.
STAINLESS STEEL
WALL GUARD
LEFT RETURN
1/4-20 x 6"
PHILLIPS FLAT HEAD SCREW
(OR APPROPRIATE FASTENER)
51SS
GASKET
51SS
BRACKET
TOGGLE
FIG. 3
CHALK LINE
FIG. 2
1. Layout the wall guard sections in the installation area.
SEE FIG. 1
2. Determine the height of the wall guard. Snap a chalk
line:
51SS - 2” [51mm] below that height
56SSF - 3”[76mm] below that height
The chalk line is the centerline of the fasteners.
3. Use the wall guard as a template to mark the mounting
hole locations. If inside and outside corners are part
of the installation allow 3-1/8” [80mm] for the bracket
and gasket depth when positioning the wall guard. The
distance from the wall to the back of the wall guard is
3-1/8” [80mm].
Drill marked holes with 3/4" drill bit for toggle bolts
(drywall installation) or 1/2" drill bit for lead anchor
(concrete wall installation). Mount brackets to wall,
tighten screws to secure.
SEE FIG. 2
4. Loosely attach the wall guard, gasket, mounting
bracket and appropriate fasteners at each mounting
location. When the installation involves longer lengths
or is a continuous installation with corners, a single
bracket is used at the butt joint.
SEE FIG. 3
STAINLESS STEEL
WALL GUARD
OUTSIDE
CORNER
INSIDE
CORNER
RIGHT
RETURN
LEFT RETURN
1/4-20 x 6"
PHILLIPS FLAT HEAD SCREW
(OR APPROPRIATE FASTENER)
51SS
GASKET
51SS
BRACKET
TOGGLE
FIG. 1
Installation Instructions
51SS and 56SSF Stainless Steel Wall Guards

Please read all instructions before installing
wallguard.
Installation Instructions
51SS and 56SSF Stainless Steel Wall Guards
FIG. 4 5. Lift the wall guard assembly to the wall, level and
tighten until secure making sure any butt joints are
aligned.
See Figure 4.
FIG. 5