inspectron WiScope WS1 User manual

LED DOWN
SWITCH IMAGER
LED UP
ZOOM
POWER / PHOTO
CONNECTION STATUS
POWER STATUS
WiScope
QUICK START GUIDE
Model: WS1

Download and Launch the App
1. Before you begin, plug your WiScope in to a wall charger or charge for
30 minutes
2. Go to the Google Play / Apple / Windows store and search "Inspectron"
3. Download App, Launch App, select "Setup WiScope / Change
communication mode", and follow the connection instructions.
What the Indicator Lights Mean
Point to Point
Connect your device
directly to the WiScope's
WIFI
Wifi Network Connection
Connect your WiScope
and your device to an
existing WIFI network
Solid - Updating WiScope to latest Firmware
Solid - An error has occured
Blinking - Booting
Solid - Connected in Hotspot mode
Blinking - Searching for a connection
Solid - Connected to WIFI and the app
Blinking Slow - Connected to WIFI, looking for app
Blinking Fast - Searching for a WIFI connection
Indicates poor signal quality when using
Wifi Network Connection

SAVE THESE INSTRUCTIONS!
General Safety Information
Read and understand all instructions.
Failure to follow all instructions listed
below may result in electric shock,
fire, and/or personal injury.
• Keep your work area clean and well lit. Cluttered benches and
dark areas may cause accidents.
• Do not operate electrical devices or video scope tool in
explosive atmospheres, such as in the presence of flammable
liquids, gases, or heavy dust. Electrical devices or visual
inspection tools create sparks which may ignite the dust or
fumes.
• Do not use the video scope around corrosive chemicals.
• Keep bystanders, children, and visitors away while operating
visual inspection tool. Do not let visitors contact the unit.
• Stay alert, watch what you are doing and use common sense.
Do not use video scope while tired or under the influence of
drugs, alcohol, or medications. A moment of inattention while
operating tools may result in serious personal injury.
• Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control of
the tool in unexpected situations.
• No naked flame sources, such as lighted candles, should be
placed on the apparatus.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Batteries (battery packs or installed batteries) shall not be
exposed to excessive heat such as sunshine, fire, or the like.
• Use safety equipment. Always wear eye protection
(users and bystanders). Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be
used for appropriate conditions.
• Use proper accessories. Do not place this product
on any unstable cart or surface. The product may
fall, causing serious injury to a person or serious
damage to the product.
Personal Safety
Work Area Safety

• Do not attempt to take any pieces of this unit apart unless
directed to by this manual.
• Provide proper cleaning. Do not use acetone to clean the
unit. Instead, use isopropanol.
• Gently clean the LCD with a dry cloth.
• Product is not CAT rated. Avoid touching live electrical
connections.
• Refer video scope to qualified service personnel under any
of the following conditions:
- If liquid has been spilled or objects have fallen into
product;
- If product does not operate normally by following the
operating instructions;
- If the product has been dropped or damaged in any way;
- When the product exhibits a distinct change in
performance.
Service
Video Scope Use and Care
• Use video scope only as directed.
• Do not immerse the handheld display unit in water. Store
in a dry place.
• Do not use the scope if condensation forms inside the lens.
Let the water evaporate before using again.
• Do not use tool if ON/OFF switch is not properly working.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Operational Temperature: 0°C to 50°C
Storage Temperature: -20°C to 60°C
• Remove batteries from product during extended storage
times.
• Protect against excessive heat. Do not use the unit near
moving machinery or areas where the temperature will
exceed 140°F (60°C).
• Replace batteries only with AA alkaline chemistry.

Warning Information to be included in a separate information sheet
included in the product.
Specific Safety Information Read this operator's manual carefully before using. Failure to
understand and follow the contents of this manual may result in electrical shock, fire
and/or severe personal injury.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: 1. This device may not cause harmful
interference. 2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE! This equipment has been tested and found to comply with the limits for Class A
digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. such modifications could void
the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. This
equipment complies with FCC's RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna(s) must not be co-located or conjunction
with any other antenna or transmitter.
IC Note : Cet appareil est conforme à la Partie 15 des règlements de la FCC et aux
normes RSS de l’Industrie du Canada. Son fonctionnement est soumis aux deux
conditions suivantes : (1) cet appareil ne doit pas causer des interférences nuisibles, et
(2) cet appareil doit accepter toute interférence reçue, y compris les interférences qui
peuvent provoquer un fonctionnement indésirable.
Le fabricant n'est pas responsable des toutes interférences radio ou télévision
causées par des modifications non autorisées apportées à cet appareil. De telles
modifications peuvent empêcher l’utilisateur d’utiliser l'appareil.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.