Inspiration Pursuit User manual

OWNER’S GUIDE
Pursuit Cross Trainer
JAN31/2010

2
Congratulations on purchasing
a fitness equipment from
Inspiration Fitness
You have chosen a high quality, safe and innovative piece of equipment as your training
partner and we are certain it will keep you motivated on the way to achieving your personal
fitness goals.
Please take the time to read this owner’s manual as it will help you to get the most out of
your new equipment.
INTRODUCTION

3
Contents
Safety Information 04
Customer Support 05
Assembly Instructions 06
Operational Instructions 12
• Quick start ................................................................. 12
• Computer instructions ....................................... 12
• Adjusting the resistance .................................... 12
• Leveling your cross trainer ............................... 13
• Battery replacement instructions ................. 13
Maintenance 14
• Storage ........................................................................ 14
• Cleaning ..................................................................... 14
• Maintenance ............................................................ 14
• Troubleshooting .................................................... 14
Warranty 15
Fitness Guide 16
• Starting and finishing your workout .......... 16
• Correct cross training form .............................. 16
• How long should I exercise for ...................... 16
• Heart rate training ................................................. 16
• Calculating your target heart rate ................ 16
• Suggested stretches ............................................ 17
Exploded Drawing / Part List 18
TABLE OF CONTENTS

4
SAFETY INFORMATION
Please read this information manual before
you begin assembly. Great care has been
taken to design these instructions and
following them will help you with quicker
assembly and minimize the risk of injury.
It is important that you keep these
instructions for future reference.
This list is not exhaustive -
You are responsible for your own safety!
• Always assemble and operate the equipment on a level surface.
• Ensure the equipment is stable before use.
• Always ensure that the equipment has adequate space
on each side.
• Try to ensure that your back is straight while exercising,
especially for long periods.
• Don’t rock the unit from side to side.
• The safety level of this equipment can only be
maintained if it is regularly examined for wear and tear.
• Keep hands away from moving parts.
• Replace defective components immediately and keep the
equipment out of use until it is repaired.
• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment pin /
fixing.
• Always check that any pins / fixings are tight and secure
before use and after adjustment.
• Never leave any adjustment devices projecting from the
equipment.
• Take care to protect carpets and floor in case of leakages.
This product is a machine that contains moving parts
which have been greased / lubricated and could leak.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear. (e.g. tracksuit
/ shorts / training shoes)
• Remove all personal jewelry before exercising.
• Ensure you warm-up well before using the equipment as
this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as this will
help to prevent muscle strain.
• Never overload the equipment. (See maximum user
weight)
• Never use the equipment in any other manner other than
the ways explained in these instructions and any wall-
chart supplied.
• Injuries to health may result from incorrect or excessive
training.
• Parents and others in charge of children should be aware
of their responsibility, because the natural play instinct
and the fondness of experimenting of children can
lead to situations and behavior for which the training
equipment is not intended.
• If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They should
be controlled and instructed in the correct use of the
equipment.
• The equipment is under no circumstances suitable as a
children’s toy.
• Children should not be allowed on or around the
equipment, especially when it is not in use.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
• This product is not suitable for therapeutic purposes.
This product has an integrated speed independent braking
system without a constant power mode that is governed by
magnetic resistance.
Maximum user weight
The maximum user weight of this equipment is 120kg.
Safety Standards
This equipment meets the requirements of the EU’s EMC and
Low Voltage directives (where applicable), AS4092-1993,
EN957 PARTS 1 & 9 - CLASS HC. Therefore the equipment
carries the following marks:
Protect the environment by not disposing of this
product or batteries with household waste. Check
your local authority for recycling advice and
facilities.

5
CUSTOMER SUppORT
Care & Maintenance
• Always place the equipment in a dry environment.
• Use a warm, damp cloth to keep the product clean.
• No wet cleaning of electrical components. Unplug before
any care and maintenance.
• The safety level of the equipment can be maintained
only if it is regularly examined for damage and wear. This
includes any ropes, pulleys, nuts, bolts, moving parts,
bushes, chains, wheels, bearings & connection points etc.
• Ensure that you inspect the product regularly - at least
once a week is recommended.
• Ensure that all fixings are tight before use.
• Always replace damaged / worn components with
original parts from the manufacturer.
Customer Support
Should you require any assistance regarding this product
please gather the following information and then contact us
using the details below:
• Serial No. - This can be found on the sticker below,
located as indicated. For future reference, please write
down your serial number in the space provided below.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
Your serial no. is:
Contact Us
ENGLAND
York Way, Daventry, Northants, England NN11 4YB
Tel: (01327) 701800
Helpdesk Tel: (01327) 701824
Fax: (01327) 706704
AUSTRALIA
Unit 1, Lot 2, Swaffham Road, Minto, N.S.W. 2566 Australia
Tel: (02) 9603 8444
Fax: (02) 9603 8555

6
ASSEMBLY INSTRUCTIONS
If you suspect you may have some parts
missing, please contact us before going
back to your retailer. Refer to the Customer
Support section for contact details.
Before you start
1. Prepare your work area -
It is important you assemble the product in a clean and
uncluttered space.
2. Work with a friend -
We recommend you have someone assist you with the
assembly as some of the components are quite heavy.
3. Open the carton -
Checking any warnings on the carton and make sure you
have it the right way up.
4. Unpack the carton -
Make sure you have the following parts:
Part No. 74 x 4
Plastic End Cap (M8)
Part No. 21 x 15
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Part No. 12 x 11
Round Head Allen Screw (M8 x 20)
Part No. 75 x 2
Hex Head Bolt (M8 x 15)
Part No. 66 x 2
Plastic End Cap
Part No. 23 x 2
Cap Nut (M10 x 1.5P x 10H)
Part No. 13 x 17
Spring Washer (M8)
Part No. 76 x 4
Spring Washer (M6)
Part No. 67 (R-Black / L) x 1 set
Lock Nut (M10 x 1.25P x 7H)
Part No. 24 x 2
Flat Washer (Ø20 x Ø11 x 2.0T)
Part No. 14 x 2
Flat Washer (Ø32 x Ø8.4 x 2.0T)
Part No. 68 x 2
Tooth Lock Washer
Part No. 79 x 2
Flat Washer (Ø24 x Ø13 x 1.5T)
Part No. 82 x 1
Wheel Knob (M8 x 1.25P x 24)
Part No. 25 x 2
Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80)
Part No. 15 x 2
Adjusting Washer (Ø32 x Ø19 x 0.5T)
Part No. 73 x 4
Plastic End Cap (M10)
Part No. 31 x 4
Carriage Bolt (M8 x 1.25P x 75)
Part No. 18 x 2
Curved Bushing (Ø32 x Ø19 x 13.5H)
Fixings
Part No. 32 x 4
End Cap Nut (M8)
Part No. 36 x 4
End Cap Nut (M6)
Part No. 43 x 4
Curved Washer (Ø12 x Ø6.4 x 1.5T)
Part No. 46 x 4
Hex Head Bolt (M6 x 1.25P x 38)
Part No. GJ-11 Part No. GJ-26-01
Part No. GJ-19
Tools

7
ASSEMBLY INSTRUCTIONS
Step 1
Step 2
Part No. 21 x 2
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Part No. 13 x 2
Spring Washer (M8)
Fixings
Part No. 32 x 2
End Cap Nut (M8)
Part No. 31 x 2
Carriage Bolt (M8 x 1.25P x 75)
Part No. 13 x 2
Spring Washer (M8)
Fixings
Part No. 32 x 2
End Cap Nut (M8)
Part No. 21 x 2
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Part No. 31 x 2
Carriage Bolt (M8 x 1.25P x 75)
Part No. 82 x 1
Wheel Knob (M8 x 1.25P x 24)

8
Step 4
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Step 3
ASSEMBLY INSTRUCTIONS
Fixings
Part No. 12 x 4
Round Head Allen Screw (M8 x 20)
Part No. 13 x 4
Spring Washer (M8)
Part No. 21 x 4
Curved Washer (Ø19 x Ø8.4 x 1.5T)

9
Step 5
ASSEMBLY INSTRUCTIONS
Fixings
Part No. 65 x 4
Cap Nut (M6)
Pre-installed
Part No. 45 x 4
Flat Washer (Ø12 x Ø6.5 x 1.5T)
Pre-installed
Part No. 74 x 2
Plastic End Cap (M8)
Step 6
Fixings
Part No. 74 x 2
Plastic End Cap (M8)
Part No. 75 x 2
Hex Head Bolt (M8 x 15)
Part No. 13 x 2
Spring Washer (M8)
Part No. 14 x 2
Flat Washer (Ø32 x Ø8.4 x 2.0T)
Part No. 15 x 2
Adjusting Washer (Ø32 x Ø19 x 0.5T)
Part No. 18 x 2
Curved Bushing (Ø32 x Ø19 x 13.5H)
Part No. 73 x 4
Plastic End Cap (M10)
Part No. 25 x 2
Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80)
Part No. 79 x 2
Flat Washer (Ø24 x Ø13 x 1.5T)
Part No. 23 x 2
Cap Nut (M10 x 1.5P x 10H)
Part No. 24 x 2
Flat Washer (Ø20 x Ø11 x 2.0T)

10
ASSEMBLY INSTRUCTIONS
Step 8
Fixings
Part No. 46 x 4
Hex Head Bolt (M6 x 1.25P x 38)
Part No. 43 x 4
Curved Washer (Ø12 x Ø6.4 x 1.5T)
Part No. 76 x 4
Spring Washer (M6)
Part No. 36 x 4
End Cap Nut (M6)
Step 7
Fixings
Part No. 66 x 2
Plastic End Cap
Part No. 67 (R-Black / L) x 1 set
Lock Nut (M10 x 1.25P x 7H)
Part No. 68 x 2
Tooth Lock Washer

11
Final Checks
Your cross trainer is now assembled. Please make the
following final checks before you use it for the first
time.
• Make sure all screws / bolts are tightened.
• Make sure you have positioned it on a flat, level
surface.
• Ensure batteries (2 x AA) are installed in
computer. (Batteries not included)
ASSEMBLY INSTRUCTIONS
Step 9
Step 10
Fixings
Part No. 12 x 3
Round Head Allen Screw (M8 x 20)
Part No. 13 x 3
Spring Washer (M8)
Part No. 21 x 3
Curved Washer (Ø19 x Ø8.4 x 1.5T)
Fixings
Part No. 83 x 4
Pan Head Philip Screw (M5 x 15)
Pre-installed on console

12
OpERATIONAL INSTRUCTIONS
Quick Start
1. Simply start pedaling and way you go!
2. The value of time, distance and calories will start counting upwards.
3. Adjust the resistance level with the large dial control knob.
Computer Instructions
USING THE METER DESCRIPTION
POWER ON • Pedal movement or push the MODE button.
POWER OFF • Automatic shut off after four minutes of inactivity.
MODE BUTTON • Press to select display functions:
SCAN / TIME / SPEED / DISTANCE / CALORIES / HEART RATE
• Press and hold for three seconds to reset all functions to zero.
FUNCTIONS DESCRIPTION
SCAN • Automatically scans each functions every 4 seconds in the following sequence:
TIME / SPEED / DISTANCE / CALORIES / HEART RATE
• To activate, press and release MODE button until SCAN appears on the display.
TIME • Display the time for one second up to 99:59 minutes.
SPEED • Display the current speed from 0 to 999.9km per hour.
DISTANCE • Display the distance from 0 to 99.99km.
CALORIES • Display the calories consumption from 0 to 999,9 kcal.
• The calories readout is an estimate for an average user. It should only be used as a
comparison between workouts on this unit.
HEART RATE Display your heart rate in beats per minute. To display heart rate, select HEART RATE mode
and grasp the pulse sensors on the handlebars, one in each hand. The heart symbol will
begin flashing when the meter senses your heart rate. Your heart rate will be displayed
approximately five seconds after the heart icon is displayed. If you do not place your hands
correctly and 60 seconds passes without a heart rate reading, the meter will turn off the heart
rate circuit. If this occurs, press the MODE button to restart, place your hands back on the
pulse sensors correctly, and the heart rate readout will appear.
NOTE: The meter will shut off automatically after four minutes of inactivity. All function values will be kept. Push the MODE
button and hold it down for three seconds to reset all functions to zero.
Adjusting the resistance
This cross trainer features a speed independent braking (resistance) system. The resistance is
controlled by a magnet, which is moved closer or further away from the flywheel - the closer
the magnet is to the flywheel the higher the resistance. The magnet is controlled manually, by
twisting the knob. The resistance levels go from easy ( - ) to hard ( + ).

13
OpERATIONAL INSTRUCTIONS
Diagram 1
Diagram 2
Leveling your cross trainer
To help you level the cross trainer on uneven surface, 2 height adjusters
are included on the rear stabilizers. Simply twist these around to adjust the
height of the cross trainer.
Battery replacement instructions:
1. Open the battery compartment cover (Diagram 1).
2. Remove battery by pulling the battery in direction of spring and
lift opposite end upwards (Diagram 2).
3. Insert 2 AA batteries ensuring you match the polarity markings
(+ and -) on the batteries with the indicators in the battery
compartment. Push flat end ( - ) against spring and when clear
push other end into holder.
4. Close the battery compartment.
Tips & Warnings
• Always change both batteries at the same time.
• Always use the same type of batteries.
• Never recharge Alkaline AA batteries.
• Do not try to heat, ignite, disassemble or throw AA batteries into
a fire.
• Do not leave old batteries in the console, and remove batteries
from the console if you won’t be using it for a long time.
Protect the environment by not disposing of this
product or batteries with household waste. Check your
local authority for recycling advice and facilities.
* PICTURE MAY VARY FROM ACTUAL MODEL.

14
MAINTENANCE
Storage
Keep the equipment in a dry place with as little temperature variation as possible. Try to protect from dust and always unplug
when not in use. (if applicable)
Cleaning
Use a warm, damp cloth to wipe the surfaces. Mild detergent may be used if necessary.
WARNING: Never remove the protective casing.
Maintenance
Ensure you regularly check components for wear and make sure all the nuts and bolts are tightened before each exercise
session.
Troubleshooting
If you are having problems with your heart rate reading please note that some fibres used in clothes (eg. polyester) create static
electricity that may prevent a reliable heart rate reading. Mobile phones, TV’s, microwaves and other electrical appliances that
generate an electromagnetic field may also interfere with heart rate measurement.
If you are still having problems with your equipment, please get in touch by using the details found in the Customer Support
page.
If you have a problem with your equipment, before you do anything else please check that all the cables have been
connected correctly. Loose cables are very common and many problems can be solved by making sure the cables are
properly connected.

15
WARRANTY
This product is supplied with a standard warranty as follows:
• 12 months frame
• 12 months other parts
• 12 months labour
This product is warranted for use in a home, personal, family or household environment Please Note: Warranty details may vary
from one market area to another
Warranty Terms
Inspiration Fitness warrants that the Product you have purchased from an authorized Inspiration Fitness reseller is free from
defects in materials and workmanship. The Warranty is valid subject to normal and reasonable use in the environment as
described above, and correct assembly of the product during the warranty period. The warranty period extends to the original
purchaser only. It is not transferable to anyone who subsequently purchases the Product from you.
The warranty excludes normal wear and tear on parts. Your sales receipt, showing the date of purchase of the product, is your
proof of the date of purchase.
This warranty becomes valid only if the Product is assembled / installed according to the instructions / directions included
with the product. This warranty does not extend to any product that has been damaged or rendered defective: (a) as a result
of accident, misuse, abuse or lack of reasonable care; (b) by the use of parts not manufactured by Inspiration Fitness or sold by
Inspiration Fitness; (c) by modification of the product; (d) as a result of service by anyone else other than Inspiration Fitness or an
authorized Inspiration Fitness warranty service provider.
During the warranty period, Inspiration Fitness will at no additional charge provide replacement part(s) or repair the product (at
Inspiration Fitness’s option) if it becomes defective, malfunctions or otherwise fails to conform with this warranty under normal,
non-commercial, personal, family or household use. In repairing the product, Inspiration Fitness may replace defective parts or
at the option of Inspiration Fitness, use serviceable used parts that are equivalent to new parts in performance. All exchanged
parts and products replaced under this warranty will become the property of Inspiration Fitness. Inspiration Fitness reserves the
right to change manufacturers of any part to cover any existing warranty.
If the product must be returned, you must return the Product or defective part to Inspiration Fitness in its original container
(or equivalent) with Proof of Purchase. Any evidence of alteration, erasing or forgery of proof of purchase documents will be
cause to void this warranty. You must prepay any shipping charges and you are responsible for insuring any product or part
that is returned. Should any product submitted for warranty service be found to be ineligible, an estimate of repair cost will be
furnished and the repair will be made if requested, upon Inspiration Fitness’s receipt of payment or acceptable arrangement
of payment. Under no circumstances will returns be accepted without return authorization by our Customer Service
department.
To obtain warranty service you must provide the following information:
Name of Product, Product Code, Batch No, Date Purchased, and Nature of fault or part number required.
Neither dealer of this product nor any retail establishment selling this product has any authority to make any warranties or to
promise remedies in addition to, or inconsistent with, those stated above. This warranty does not affect your statutory rights.
Please note that warranty terms may vary from one market area to another.

16
FITNESS GUIDE
Starting And Finishing Your Workout
Begin and end each workout with a Warm Up / Down session - a few minutes of stretching to help prevent strains, pulls and
cramps.
Correct Cross Training Form
To start using the cross trainer, simply stand on the foot pedals with the front of your shoes close to the front edge of the pedal
cap. Place your hands at a comfortable position on the handlebars. Simply move your highest foot forward and follow the
natural path of the machine.
Start on a load level that is comfortable to familiarize yourself with the machine. Once you are comfortable, start adjusting the
load level to achieve the workout desired.
Forward and Reverse: The cross trainer can be used in the forward and reverse direction to vary the muscles that you workout.
This will also vary your workout helping you to stay motivated. To change directions, simply slow the pedals down until they
stop and switch directions.
Load Level Adjustment: The load level of cross trainer can be changed at any time during your workout. Adjusting your load
level will allow you to increase or decrease your intensity level.
How Long Should I Exercise For?
That really depends on your current level of fitness. If you’re just starting out on a new exercise program, you should start
gradually and build up - do not try to do too much too quickly. 30 minutes, 3 times a week should be enough.
Don’t push yourself too hard - you should never feel exhausted during or following exercise.
Heart Rate Training
To get the most out of your new piece of fitness equipment and see the best results from your training you should exercise
at the right level of effort, and that means listening to your heart! Work out to a target heart rate means you can direct your
workout to achieve different goals:
Good health - For those wishing to improve quality of life and general well being. Your sessions will need to be done at an
intensity of between 50 - 60% of your estimated maximum heart rate, should last about 30 minutes and can be done on most
days of the week.
Weight loss - To see a significant reduction in body fat, your sessions must be a little more intense - between 60 and 70% of
your estimated maximum heart rate. These sessions can also be performed on most days of the week for up to 30 minutes.
Improving tness levels - These sessions should be performed at 70 - 80% of your estimated maximum heart rate and can also
involve bouts of interval training that would have your heart rate peaking for short times near your maximum heart rate level.
These are intense sessions and will require at least a 48 hour rest between sessions.
Calculating Your Target Heart Rate
First, you need to find your estimated maximum heart rate using the formula “220 minus your age in years”. So, if you are 35
years old your estimated maximum heart rate is:
220 - 35 = 185 beats per minute (bpm)
Next, to calculate your target heart rate, simply multiply your estimated maximum heart rate (185bpm) by the applicable
percentage. So, if your goal is better health:
185 x 60% = 111bpm
NOTE: The important issue to remember with all estimated calculations is that they are just estimates - if you don’t feel
comfortable exercising at your target then reduce it to a level you are comfortable with.
Heart rate training requires you to monitor your heart rate throughout the workout. For this we recommend using a chest strap
(if your machine has a wireless receiver) or a heart rate monitor. For more information please get in touch using the Contact Us
details.
Always consult your doctor before undertaking a new exercise regime.
If you experience nausea, dizziness or other abnormal symptoms during exercise, stop at once and consult your doctor.

17
FITNESS GUIDE
Suggested Stretches
The correct form for several basic stretches is shown at the
right. Move slowly as you stretch—never bounce.
1. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite
foot toward you and rest it against the inner thigh of your
extended leg. Reach toward your toes as far as possible.
Hold for 15 counts, then relax. Repeat 3 times for each leg.
Stretches: Hamstrings, lower back and groin.
2. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean
forward and move your hips toward the wall. Hold for 15
counts, then relax. Repeat 3 times for each leg. To cause
further stretching of the achilles tendons, bend your back leg
as well. Stretches: Calves, achilles tendons and ankles.
3. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
4. Inner Thigh Stretch
Sit with the soles of your feet together and your knees
outward. Pull your feet toward your groin area as far as
possible. Hold for 15 counts, then relax. Repeat 3 times.
Stretches: Quadriceps and hip muscles.

18
ExpLODED DRAWING

19
pART LIST
KEY PART NO. DESCRIPTION QTY
1 52036-107 Front Post 1
2 52036-02 Rear Post 1
3 52036-03 Main Post 1
4 52036-04 Handlebar Post 1p
5 52036-05 Pedal Support Post 2
6 52036-06 Pedal Support Post Joint 2
7 52036-07 Belt Support Wheel 1
8 52036-08 Small Handlebar Post 1
9 52036-09 Hand Pulse Sensor 2
10 52036-10 Hand Pulse Sensor Cable 1
11 52036-11 Round Head Self Tapping Screw (M14 x 15) 2
12 52036-12 Round Head Allen Screw (M8 x 1.5P x 20) 11
13 52036-13 Spring Washer (M8) 19
14 52036-14 Flat Washer (Ø32 x Ø8.4 x 2.0T) 2
15 52036-15 Adjusting Washer (Ø32 x Ø19 x 0.5T) 2
16 52036-16 Sleeve (Ø32 x Ø26 x Ø19) 4
17 52036-17 Console 1
18 52036-18 Curved Bushing (Ø32 x Ø19 x 13.5H) 2
19 52036-19 Upper Handlebar Post 1P
20 52036-20 Tension Knob (8 Level) 1
21 52036-21 Curved Washer (Ø19 x Ø8.4 x 1.5T) 15
22 52036-108 Sensor Cable 1
23 52036-23 Cap Nut (M10 x 1.5P x 10H) 2
24 52036-24 Flat Washer (Ø20 x Ø11 x 2.0T ) 2
25 52036-25 Hex Carriage Bolt (Ø12 x M10 x 1.5P x 80) 2
26 52036-26 Pedal (900) 1P
27 52036-106 Main Cover 1P
28 52036-28 End Cap 1
29 52036-29 Wheel Foot Cap (Ø60) 2
30 52036-30 Front Floor Support 1
31 52036-31 Carriage Bolt (M8 x 1.25P x 75) 4
32 52036-32 End Cap Nut (M8) 4
33 52036-33 Metal Sleeve 4
34 52036-34 Belt 1
35 52036-35 High Density Handlebar Sleeve (Ø32 x 600 x 5.0) 2
36 52036-36 End Cap Nut (M6) 4
37 52036-37 Washer (Ø32 x Ø16.3 x 0.5T) 1
38 52036-38 Round Head Self Tapping Screw (M5 x 15) 1
39 52036-39 Split End Sensor Cable Set 1
40 52036-40 Adjusting Assembly 2
41 52036-41 Locknut (3/8” x 26W x 4H) 1
42 52036-42 Locknut (3/8” x 26W x 7H) 3
43 52036-43 Curved Washer (Ø12 x Ø6.4 x 1.5T) 4
44 52036-44 Flat Washer (Ø25 x Ø8.2 x 1.5T) 2
45 52036-45 Flat Washer (Ø12 x Ø6.5 x 1.5T) 4
46 52036-46 Hex Head Bolt (M6 x 1.25P x 38) 4
47 52036-47 Internal Bushing 4
48 52036-48 Sphere Washer (Ø23 x Ø17 x 0.4T) 2
49 52036-49 Double Sided Magnetic Wheel 1
50 52036-50 Cap Nut (M10 x 1.5P x 7H) 2
51 52036-51 End Cap (Ø1) 2
52 52036-52 Countersunk Roller 1
53 52036-53 Bushing (Ø16 x Ø10 x 18) 1
54 52036-54 Sphere End Cap 2
55 52036-55 Roller Secure Bracket 1
56 52036-56 Flat Head Allen Screw (M10 x 1.5P x 40) 1
57 52036-57 Spring (Ø17 x Ø2.3 x 83) 1
58 52036-58 Bushing (Ø60) 2
59 52036-59 Pan Head Phillip Screw (M5 x 0.8P x 60) 1
60 52036-60 Foam Piece 2
KEY PART NO. DESCRIPTION QTY
61 52036-61 Round Head Self Tapping Screw (M4 x 12) 8
62 52036-62 Button Head Self Tapping Screw (M5 x 25) 4
63 52036-63 Lower Adjusting Wire 1
64 52036-64 Small Handlebar Sleeve 2
65 52036-65 Cap Nut (M6) 4
66 52036-66 Plastic End Cap 2
67 52036-67 Lock Nut (M10 x 1.25P x 7H / R-Black / L) 1P
68 52036-68 Tooth Lock Washer 2
69 52036-69 C-Clip (Ø17) 2
70 52036-70 Adjusting Washer (Ø22 x Ø17 x 0.5T) 1
71 52036-71 Bearing 2
72 52036-72 Pedal Support Post Joint Cap 2
73 52036-73 Plastic End Cap (M10) 4
74 52036-74 Plastic End Cap (M8) 4
75 52036-75 Hex Head Bolt (M8 x 15) 4
76 52036-76 Spring Washer (M6) 4
77 52036-77 Round Head Allen Screw (M10 x 20) 1
78 52036-78 Screw End Cap (M10 x 20) 2
79 52036-79 Flat Washer (Ø24 x Ø13 x 1.5T) 2
80 52036-80 Rear Floor Support 1
81 52036-81 C-Clip 2
82 52036-82 Wheel Knob (#24) 1
83 52036-83 Pan Head Phillip Screw (M5 x 15L) 4
84 52036-84 Tension Knob Support Post 1
85 52036-85 Cable Pulling Extension 1

Other manuals for Pursuit
1
Table of contents