Intellinet 505932 User manual

HI-SPEED USB 2.0
GIGABIT ETHERNET
ADAPTER
USER MANUAL
MODEL 505932
INT-505932-UM-0511-04

1
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause undesired operation.
CE Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN
55022 class B for ITE, the essential protection requirement of Council Directive 2004/108/EC on
the approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information
in this document is not up-to-date. Please check with your local distributors for the latest
information. No part of this document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2010, All Rights Reserved.

2
1. Unpacking Information
Thank you for purchasing the USB to Gigabit Ethernet adapter. Before you start, please
verify that your package contains the following items:
1. One USB to Gigabit Ethernet Adapter.
2. One driver & manual CD
2. Overview
2.1 Introduction
This USB to Gigabit Ethernet adapter is a cost-effective solution that converts a USB
port into a 10/100/1000 Base-T Ethernet port. It enables a low-cost and affordable
Gigabit Ethernet network connection to desktop and notebook PCs and embedded
systemsusing popular USB ports: no need to purchase an expensive Gigabit network
interface card or use a PCI or Card bus slot — just plug into an available USB port on a
desktop or laptop PC running Windows 7/2003/XP/Vista or Linux/Mac.
Installation and operation are further simplified by living up to USB's Plug and Play
installation approach to connecting computer peripherals. You will not need to open the
case of your computer, nor will you be required to set IRQs. It also supports full and half
duplex mode to achieve the best speeds for each attached device, and hot-swap
capability provides the simplest way to connect your computer to an Ethernet-based
network.

3
2.2 Key Features
Complies with IEEE 802.3 10BASE-T standard
Complies with IEEE 802.3u 100BASE-TX standard
Complies with IEEE 802.3ab 1000BASE-T standard
Compliant with USB 1.1 and 2.0 standards
Complies with IEEE 802.3x Flow Control
Supportsfull/half duplex operation
Plug and Play Installation
Support hot inserting and swapping
Automatically negotiates 10/100/1000 Mbps connection rate
Support drivers for Windows 7/2003/XP/ Vista/Linux/Mac
FCC, CE Class B
2.3 LED Definition
Power
Green: Power is on
Off: Power is off
10/100M Link/ACT
Green: Valid link on this port
Blinking: Data transferring/ receiving on this port
Off: No Valid Link on this port or the port is connected at 1000 Mbps
1000M Link/ACT
Green: Valid link on this port
Blinking: Data transferring/ receiving on this port
Off: No Valid Link on this port or the port is connected at 10/100 Mbps

4
3. Installing the USB to Gigabit Ethernet Adapter
3.1 System Requirements
Pentium 166 MMX or above processor-based PC
Available USB port
Microsoft Windows 7/2003/XP/Vista or Linux or Mac
CD-ROM Drive
3.2 Hardware Installation
Before installation, check if there is an available active USB port. To check this, go
to My Computer > Control Panel > System, then click the Device Manager tab to
check if the Universal Serial Bus controller is displayed, as shown below.

5
3.2.1 Connect the Adapter to your PC
1. Plug the USB adapter into your PC.
2. Windows will detect the new hardware automatically and prompt you for the
driver. For driver installation, refer to the chapter “Software Installation.”
3.3 Software Installation
After attaching the USB to Gigabit Ethernet adapter to your PC or laptop, the
auto-detection for new hardware will be activated automatically. The procedures to
perform driver installation differ slightly from each operation system: Refer to the
following sections.
3.3.1Windows XP Setup
1. Select “Install from a list or specific location,” then click next.

6
2. Insert the provided driver CD. Select “Include this location in the search,” then click
“Browse.”

7
3. Choose the location of your CD-ROM. Locate the setup.exe file in the folder
“D:505932_USB_ Gigabit_Ethernet_Adapter\WinXP,” where “D” is the designation
of your CD drive. Click “Next” to proceed.
4. A caution window may pop up. Click ”Continue Anyway.” There won’t be any effect
on the performance of the adapter.

8
5. Click “Finish”to complete the installation and activate the adapter.

9
3.3.2Windows Vista setup
1. When the Found New Hardware box appears, close this window.
2. Go to Start Control Panel Hardware and Sound Device Manager.
3. Double-click the “AX178” icon.

10
4. Click the “Reinstall Driver” button.
5. Select “Browse my computer for driver software.”

11
6. Click the “Browse”button and select Computer your CD-ROM drive 
“D:505932_USB_ Gigabit_Ethernet_Adapter\Vista,” where “D” is the
designation of your CD drive. Click “OK”to proceed.
7. Click “Next” to begin the installation.
8. Wait a few moments while it installs the driver.
9. Click the “Close”button to finish the installation.

12
3.3.3Windows 7 Setup
1. Locate the setup.exe file on the included setup CD in the folder “D:505932_USB_
Gigabit_Ethernet_Adapter\Win7,” where “D” is the designation of your CD drive.
Double-click the setup icon to begin the installation, then follow the on-screen
instructions. When the “Preparing to Install” screen displays, wait a few moments while
the installation continues.

13
2. After the installation is complete, click the “Finish” button.

14
3.3.4MAC OS Setup
1. Insert the CD driver into the CD-ROM drive. Go to Computer > CD ROM >
“505932_ USB_ Gigabit_Ethernet_Adapter” > Mac.
2. Double-click and run the installation package.
3. When the Welcome screen displays, click “Continue.”
4. When the Select a Destination interface displays, select an install location and click
“Continue.”

15
5. Click “Go Back”to change the install location or click “Install”and continue.

16
6. If prompted, enter your User Name and Password and click “OK.”
7. Click “Continue Installation.”

17
8. Wait a few moments for the installation.
9. After the driveris successfully installed, click “Restart”and the computer will
reboot automatically.

18
4. Product Specifications
Standards
IEEE802.3, 10BASE-T
IEEE802.3u, 100BASE-TX
IEEE802.3ab, 1000BASE-T
IEEE802.3x Flow control
USB 1.1/ 2.0
Interface
1*10/100/1000 Mbps RJ-45 port
1*USB type A male connector
Cable Connections
UTP Category 3,4,5,5e
Network Data Rate
1000Mbps, 100Mbps, 10Mbps
Jumbo Frame
9k bytes
LED indications
1* 1000M Link/ACT
1* 10/100M Link/ACT
1* Power
Max Power
Consumption
1.41W
Temperature
Operating: 0°C ~ 40°C (32°~104°F)
Storage: -20°C ~ 70°C (-4°~158°F)
Humidity
Operating: 10% ~ 90% RH, non-condensing
Storage: 5%~90% RH, non-condensing
Operation System
Windows 7/2003/XP/Vista; Mac
Emission
FCC, CE Class B
Weight
63g