Intellinet 503549 User manual

DIN RaIl
PoweR
SuPPly
uSeR
maNual
MODELS 503549,
503556 & 503563
INT-503549/503556/503563-UM-0208-01

2
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™
DIN Rail Power Supply, Model 503549 (45 W / 2 A), Model 503563 (75
W / 3.2 A) or Model 503556 (120 W / 5 A).
This series of industrial power supplies provides reliable DC power for
any industrial Ethernet 24 V DC media converter or switch. Presenting
a rugged design, incorporating all international standards and approvals,
and offering short circuit, overload, over-voltage and over-temperature
protection, these high-quality power supplies have passed a 100%
full-load burn-in test and are UL/cUL listed, TUV/CB certied and CE
marked.
Easy-to-follow instructions in this user manual help make installation
of the switch quick and simple, so you’ll also soon be enjoying the
benets of these additional features:
• Universal AC input (85 – 264 V AC)
• DC-compatible input (120 – 370 V DC)
• Simple snap-on installation for TS35/7.5 or TS35/15 DIN rails
• Free-air cooling convection
• Built-in EMI lter and low ripple noise
• Lifetime Warranty
mouNtINg/INStallatIoN
Prior to installation, make sure that the power supply will be properly
ventilated for adequate heat dissipation.
• Do not cover the top or bottom surfaces of
the unit.
• When installing multiple units, leave enough
space between them for cooling.
• Forcing air over the unit(s) improves heat
dissipation.
Each of these DIN Rail Power Supply models
will attach to TS35/7.5 or TS35/15 DIN rails.
1. Insert the upper part of the DIN rail clip on the
power supply into the DIN rail track.

2. Pull down the plastic DIN rail lock beneath the clip and push the bottom
of the clip into the track.
3. Release the lock and check that the clip is securely positioned in the
track.
wIRINg/coNNectIoNS
Model 503549 (45 W / 2 A)
Connecting to DC Output: Insert the positive and negative wires into the
+V terminal contact (Pin 6 or 7) and –V terminal contact (Pin 4 or 5),
then tighten the terminal screws to prevent the wires from becoming
loose. NOTE: Always make sure that DC wiring is connected with the
correct polarity.
Connecting to AC Input: Insert the AC power lines into the Pin 1 and Pin 2
terminal contacts, then tighten the terminal screws to prevent the AC
wires from becoming loose.
Connecting to Ground: Connect the frame ground (Pin 3) of the power
supply to any nearby reliable ground with a thick wire to help ensure
safety and prevent system “noise.”
3
Pin No. Assignment
1 AC/ L
2 AC/ N
3 Ground
4/5 DC Output –V
6/7 DC Output +V
8 LED
9 +V Adj.
Pin 1
Pin 9

Model 503563 (75 W / 3.2 A) & 503556 (120 W / 5 A)
Connecting to DC Output: Insert the positive and negative wires into the
+V terminal contact (Pin 1 or 2) and –V terminal contact (Pin 3 or 4)
of Terminal Board 2, then tighten the terminal screws to prevent the
wires from becoming loose. NOTE: Always make sure that DC wiring
is connected with the correct polarity.
Connecting to AC Input: Insert the AC power lines into the Pin 2 and Pin 3
terminal contacts of Terminal Board 1, then tighten the terminal screws
to prevent the AC wires from becoming loose.
Connecting to Ground: Connect the frame ground (Pin 1) of Terminal
Board 1 of the power supply to any nearby reliable ground with a
thick wire to help ensure safety and prevent system “noise.”
4
Pin 1 Terminal Board (TB) 1
Terminal Board (TB) 2Pin 1 Terminal Board 2
Pin No. Assignment
1/2 DC Output +V
3/4 DC Output –V
Terminal Board 1
Pin No. Assignment
1 Ground
2 AC/ N
3 AC/ L

SPecIfIcatIoNS
5
MODEL 503549
General
• Power supply:
- Input voltage: 85 – 264 V AC,
120 – 370 V DC
- Output: 45 W, 24 V DC, 2 A
• Output voltage tolerance: +/- 1%
• Output rated current: 2 A
• Output current range: 0 – 2 A
• Ripple and noise: 480 mVp-p
• Line regulation: +/- 1%
• Load regulation: +/- 1%
• Efciency: 80%
• DC voltage adjust: +/- 10%
• Setup, rise and holdup time: 800
ms, 60 ms and 50 ms / 230 V
Operation Protection
• Inrush current: cold start at 30 A /
115 V or 60 A / 230 V
• Leakage current: < 1 mA / 240
V AC
• Withstand voltage:
- Between input & output: 3 kV AC
- Between input & frame ground:
1.5 kV AC
- Between output & frame ground:
0.5 kV AC
• Isolation resistance: between input
& output / input & frame ground /
output & frame ground: 500 V DC
/ 100 Ohms
• Overload protection: 105 – 150%;
type: constant current limiting;
reset: auto recovery
• Over-voltage protection: 115 –
135 V DC
LEDs
• Power
Environmental
• Dimensions: 78 x 96 x 67 mm
(W x H x D) (3.0 x 3.8 x 2.6 in.)
• Weight: 400 g (0.9 lbs.)
• Operating temperature: -10 – 50°C
(14 – 122°F)
• Operating humidity: 5 – 90% RH,
non-condensing
• Storage temperature: -20 – 85°C
(-4 – 185°F)
Regulatory Approvals
• EMC:
- CISPR22 (EN55022) Class B
- EN61000-4-2
- EN61000-4-3
- EN61000-4-4
- EN61000-4-5
- EN61000-4-6
- EN61000-4-8
- EN61000-4-11
- EN61000-3-2
- EN50082-2
- ENV50204
• Safety:
- UL508
- CE/EN60950

6
MODEL 503563
General
• Power supply:
- Input voltage: 85 – 264 V AC,
120 – 370 V DC
- Output: 76.8 W, 24 V DC, 3.2 A
• Output voltage tolerance: +/- 1%
• Output rated current: 2 A
• Output current range: 0 – 3.2 A
• Ripple and noise: 480 mVp-p
• Line regulation: +/- 0.5%
• Load regulation: +/- 1%
• Efciency: 80%
• DC voltage adjust: 24 – 28 V
• Setup, rise and holdup time:
- 1000 ms, 60 ms, 50 ms / 230 V
- 1800 ms, 60 ms, 10 ms / 115 V
Operation Protection
• Inrush current: cold start at 30 A /
115 V or 60 A / 230 V
• Leakage current: < 1 mA / 240 V
AC
• Withstand voltage:
- Between input & output: 3 kV AC
- Between input & frame ground:
1.5 kV AC
- Between output & frame ground:
0.5 kV AC
• Isolation resistance: between input
& output / input & frame ground /
output & frame ground: 500 V DC
/ 100 Ohms
• Overload protection: 105 – 150%;
type: constant current limiting;
reset: auto recovery
• Over voltage protection:
29 – 34 V DC
• Over temperature protection:
85°C +/- 5°C, power shutdown
LEDs
• DC OK
Environmental
• Dimensions: 55.5 x 125.2 x 100 mm
(W x H x D) (2.2 x 4.9 x 3.9 in.)
• Weight: 550 g (1.2 lbs.)
• Operating temperature: -10 – 60°C
(14 – 140°F)
• Operating humidity: 20 – 90% RH,
non-condensing
• Storage temperature: -20 – 85°C
(-4 – 185°F)
Regulatory Approvals
• EMC:
- CISPR22 (EN55022) Class B
- EN61000-4-2
- EN61000-4-3
- EN61000-4-4
- EN61000-4-5
- EN61000-4-6
- EN61000-4-8
- EN61000-4-11
- EN61000-3-2
- EN50082-2
- ENV50204
• Safety:
- UL508
- CE/EN60950

7
MODEL 503556
General
• Power supply:
- Input voltage: 88 – 132 V AC /
176 – 264 V AC by switch or
254 – 370 V DC
- Output: 120 W, 24 V DC, 5 A
• Output voltage tolerance: +/- 1%
• Output rated current: 2 A
• Output current range: 0 – 3.2 A
• Ripple and noise: 80 mVp-p
• Line regulation: +/- 0.5%
• Load regulation: +/- 1%
• Efciency: 84%
• DC voltage adjust: 24 – 28 V
• Setup, rise and holdup time:
- 500 ms, 70 ms, 30 ms / 230 V
and 115 V
Operation Protection
• Inrush current: cold start at 30 A /
115 V or 60 A / 230 V
• Leakage current: < 3.5 mA /
240 V AC
• Withstand voltage:
- Between input & output: 3 kV AC
- Between input & frame ground:
1.5 kV AC
- Between output & frame ground:
0.5 kV AC
• Isolation resistance: between input
& output / input & frame ground /
output & frame ground: 500 V DC
/ 100 Ohms
• Overload protection: 105 – 150%;
type: constant current limiting;
reset: auto recovery
• Over voltage protection:
29 – 33 V DC
• Over temperature protection:
90°C +/- 5°C, power shutdown
LEDs
• DC OK
Environmental
• Dimensions: 65.5 x 125.2 x 100 mm
(W x H x D) (2.5 x 4.9 x 3.9 in.)
• Weight: 650 g (1.4 lbs.)
• Operating temperature: -10 – 60°C
(14 – 140°F)
• Operating humidity: 20 – 90% RH,
non-condensing
• Storage temperature: -20 – 85°C
(-4 – 185°F)
Regulatory Approvals
• EMC:
- CISPR22 (EN55022) Class B
- EN61000-4-2
- EN61000-4-3
- EN61000-4-4
- EN61000-4-5
- EN61000-4-6
- EN61000-4-8
- EN61000-4-11
- EN61000-3-2
- EN50082-2
- ENV50204
• Safety:
- UL508
- CE/EN60950

INTELLINET NETWORK SOLUTIONS™offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.