Intellitec LPL822 User manual

Operation
Washing: 20 Seconds
1. Press the Wash Button. The lens will illuminate green and begin to blink.
2. Wash your hands using warm water and soap as the green LED Light/Timer is blinking. The speed of the green flashing light
indicates your progress: it will blink faster as you get closer to finishing.
3. The lens will turn red when the time is up.
Brushing: 2 Minutes
1. Press the Brush Button. The lens will illuminate green and begin to blink.
2. Brush your teeth using your favorite toothpaste as the green LED Light/Timer is blinking. The speed of the green flashing light
indicates your progress.
3. The lens will turn red when the time is up.
NOTE: If you accidentally press the wrong button, simply press the rest button to reset the unit.
Mounting the Timer
Hook and Loop Tape (included):
1. Check the location of where you want to place the Timer. Make sure it is clean and that there is no debris or dust.
2. Remove the suction cup from the back of the bracket by sliding it down and pulling it away from the bracket.
3. The two sides of the hoop and loop tape come pre-attached for ease of mounting. Remove the paper covering on one sticky
side of the tape.
NOTE: Hook and loop tape may be cut to desired size for easier removal.
4. Place the tape in the recessed area in the center on the back of the Mounting Bracket.
5. Remove the paper covering on the other sticky side of the tape.
6. Place the Mounting Bracket in the desired location. Press firmly and hold for five (5) seconds so that the tape adheres to
the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage surface.
Screw (included):
You can secure the Timer mounting bracket to almost any surface using a screw. To do so, remove the Timer from the bracket by
sliding it up and out of the bracket.
1. Drill a pilot hole in the location where you want to mount the Timer. Place screw (included) in pre-drilled hole. Tighten slightly
until secure, but do not tighten all the way. Slide the Mounting Bracket keyhole slot over screw head and into position.
2. Tighten screw to secure mounting bracket to wall. Take care to not over tighten.
3. Place the Timer in the mounting bracket.
Suction Cup (included):
Use the suction cup to secure the mounting bracket to surfaces such as tile.
1. Slightly moisten the suction cup and press it onto the mounting surface.
2. The suction cup has a small pull tab for ease of release from mounting surface.
NOTE: If suction cup releases from mounting surface over time, repeat step 1 above.
LED “WASH & BRUSH” TIMER
LPL822 Owner’s Manual 12
3
4
5
6
Location of Controls:
1. Wash Button
2. Brush Button
3. LED Light
4. Reset Button
5. Mounting Bracket
6. Battery Compartment*
Unit requires 3 x 1.5V
AAA Batteries (not included)
*On back of unit
Mounting Bracket
Hook & Loop
Ta pe Area
Keyhole
Slot
LPL822 Manual.indd 2 4/20/11 11:11:18 AM

Battery Installation/Replacement:
If the illuminated lens appears to be dim or does not light at all this is an indication that your batteries need to be replaced.
1. Remove the Timer from its Mounting Bracket by sliding it up and out of the bracket.
2. Pull up on the battery compartment housing tab on the back of unit to open the battery compartment.
3. Remove the old batteries (if replacing).
4. Insert 3 new AAA batteries. Be sure to match the battery polarity guide when installing new batteries.
5. Replace the battery compartment cover.
Battery Precautions
1. Use only the size and type of batteries specified.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fire.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
042011 © 2011 Lancer & Loader Group LLC. All rights reserved. Custom manufactured in China for Lancer and Loader Group LLC, New York, NY 10016.
BATTERY BATTERY
BATTERY
Customer Service
Answers to the most commonly asked questions can be found at www.lancerandloader.com
Limited 2 Year Warranty
If you recently purchased the item the quickest option is to return the product to the retailer where the item was purchased. Return policies vary by retailer.
If returning the item to the retailer is not possible visit www.lancerandloader.com for warranty details and directions on how to have the product repaired
or replaced.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifications to this product not approved by the party responsible for compliance could void the user’s authority
to operate the product.
LPL822 Manual.indd 3 4/20/11 11:11:18 AM