Elkay Energy sense User manual

push button/touch timer fitting & operating instructions
The push button/touch timer are pa r t of the Elk a y familk o f s witche s ,timer s
and de tectors w h ich save e n ergy and i n crease c o nvenie n ce in and ar o und your
home ,garden o r p remise s .
RATING AT 240V AC
Incandescent 16A
Fluorescent 16A
Compact 16A
Fluoescent
Resistive 16A
TimeDelay 2mins-2hours.
USAGE
The pu sh button /touch ti m ers are ge n eral
purp ose time co ntrols. A pplica t ions for
suit able use in clude lig h ting,h e ating an d
vent ilation . T he timer s c an be used
inde pendent l y or as a mast e r unit whe n
usin g slave tri gger swit c hes.
MOUNTING AND INSTALLATION
pl ea se note tha t it i s es sential t ha t th e Live InImportant
wi re a nd switch L iv e Ou t is identi fi ed p rior to
co mm encing in st al latio n. Tu rn off main s su pp ly for
in st allatio n. Yo ur Elka y un it i s co mpati bl e wi th a single
ga ng ,25mm dee p, Br itish S ta nd ard acces so ry p late.pl ea se
en su re that the t op a nd b ottom lug s ar e re moved ,i f
fi tt ed,from m et al w all box es p ri or to fitti ng .E nsure tha t
th er e is adequa te s pa ce for wiri ng .
Step 1 plac e th e Li ve In wire, as p er d iagram, in to t he left
ha nd p osition o f th a co nnector ,t he s witch ed L iv e Out
wi re i nto the sec co nd f rom left po si ti on of con ne ct or.(see
di ag ram1)
Step 2 To set t im e, a s per timin g ta bl e, use swit ch es o ne
th ro ugh four. D ep en ding on req ui re d time av ai la ble from
2 mi nu tes to 2 hour s. E .g 1 0 minutes = s wi tc h one - off ,
sw it ch two - on, sw it ch t hree - off, s wi tc h four - off.
(s ee d iagram 2)
pushbuttontimer
touchtime
energysense
energystyle
energyoutdoor

ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
ON
DIP
4
3
2
1
2 mins 5 mins 10 mins 15 mins 20 mins 25 mins
30 mins
40 mins
50 mins 60 mins 70 mins 80 mins 90 mins 100 mins 110 mins 120 mins
Diagram 2
step 3 Re-apply mains supply. The biue locator ring will light up around the push button/touch pad.
Your light source or appliance,will now be switched off. please refer to operation section.
OUTDOOR INSTALLATION
please note only produccts in the tuodi energy outdoor range are suitable for use outdoors. tuodi
energy outdoor can only be used in conjunction with the surface mount box supplied.
Take the surface mount box and remove knock out section. If required and to ensure Ip66 waterproof
rating, please use a suitable M20 cable gland. Mount the surface mount box on a secure surface using
the mounting pack supplied. place screw cover seals over the mounting screws.
- Install as per previous timer instructionsTurn off mains supply before proceeding with installation
- Mount unit onto surface mount box using the fixing screws at all four corners - place screw hole seals
over left and right screw cavities - Clip on front fascia plate - Re-instate mains supply.
OPERATION
press the push button/touch pad and the red LED will light up. Your light source or appliance will1.
now be switched on.
At any time during the working of the light source or appliance, the push button/touch pad can de2.
pressed to reset the timing sequence to the originally set time. E.g when the timing period is 30
minutes, if push button/touch pad is pressed 15 minutes into the sequence, the timer will re-set for a
further 30 minutes.
To end the timing sequence prematurely, press and hold the push button/touch pad until the red3.
LED flashes continuously indicating the last minute of operation. Your light source or appliance will be
switched off, after one minute.
At one minute prior to the end of the timing sequence, the red LED will begin to flash continuously4.
for the last minute of operation. The blue locator ring will then illuminate once the light source or
appliance has gone off.
IMPORTANT NOTICE
All wiring should be carried out by a competent person or a qualified Electrician in accordance with the
current IEE Wiring Regulations. If unit is faulty return to place of purchase.