interactive scape Tangible st55-005 User manual

Scape®
Tangible
st55-005
Operating manual

1. General
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 2 of 27 poc: SFi
Scape® Tangible
Operating manual
Content
1. General _____________________________________________________________________________________________________________4
1.1. Safety instructions ___________________________________________________________________________________________________ 4
1.2. Scope of delivery ____________________________________________________________________________________________________ 6
1.3. Cleaning instructions ________________________________________________________________________________________________ 6
1.4. Transportation instructions__________________________________________________________________________________________ 6
2. Specifications and set up___________________________________________________________________________________________ 7
2.1. Specifications_________________________________________________________________________________________________________7
2.2. Connections and controls ____________________________________________________________________________________________7
2.3. Remote control ______________________________________________________________________________________________________ 8
3. Installation _________________________________________________________________________________________________________9
3.1. Ventilation guide____________________________________________________________________________________________________ 10
3.1.1. Guidelines for housing the hardware______________________________________________________________________________ 11
3.1.2. Diagram for housing a Scape® Tangible __________________________________________________________________________ 11
3.1.3. Housing with additional heat sources ____________________________________________________________________________12
4. Connection ________________________________________________________________________________________________________ 13
4.1. Notes ________________________________________________________________________________________________________________13
4.2. Connection to the power supply_____________________________________________________________________________________13
4.3. Connection to the PC________________________________________________________________________________________________13
4.4. Connection to the network __________________________________________________________________________________________13
5. Switching on ______________________________________________________________________________________________________ 14
6. Display settings – OSD ____________________________________________________________________________________________ 15
6.1. OSD usage___________________________________________________________________________________________________________15
7. Troubleshooting tips ______________________________________________________________________________________________ 16
7.1. Manufacturer – Support _____________________________________________________________________________________________16
7.2. Problems and solutions ______________________________________________________________________________________________16
8. Annex _____________________________________________________________________________________________________________ 17
8.1. Technical data _______________________________________________________________________________________________________17
8.2. Technical Drawings__________________________________________________________________________________________________18
8.2.1. Perspective_______________________________________________________________________________________________________18
8.2.2. Top view _________________________________________________________________________________________________________19
8.2.3. Bottom view_____________________________________________________________________________________________________ 20
8.2.4. Front view ______________________________________________________________________________________________________ 22
8.2.5. Back view _______________________________________________________________________________________________________ 23
8.2.6. Right view_______________________________________________________________________________________________________ 24
8.2.7. Detail A – Power connection ____________________________________________________________________________________ 25
8.2.8. Detail B – Media connections ___________________________________________________________________________________ 26

1. General
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 3 of 27 poc: SFi
Notes
This is a class A device according to EN55022.
For more information, please refer to Chapter 1.1 - Radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003.
This manual is applicable for the following device:
·Scape® Tangible 55" (st55-005 R2.1)
Information in this document is subject to change without notice.
©2019 Interactive Scape GmbH. All rights reserved.
The document or excerpts from the document may not be duplicated without the prior permission of Interactive Scape
GmbH.
Interactive Scape GmbH shall not be liable for any errors contained in this document or any other incidental or
consequential damages resulting from the delivery, use or application of this material.
All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

1. General
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 4 of 27 poc: SFi
1. General
This manual describes the safe installation, configuration and correct operation of the
Scape® Tangible.
If necessary, pay attention to the supplementary documents, such as the installation instructions.
1.1. Safety instructions
Before using and operating your Scape® Tangible, observe the following safety instructions to prevent yourself, your
environment and the Scape® Tangible from being damaged.
Fire and electric shock
Overloaded sockets, extension cords and power strips can cause fire and electric shock.
·Avoid using power strips and extension cords if possible.
·Do not chain multiple extension cords or power strips together.
Overheating
Heat build-up can overheat the screen. This can damage the device.
·Ensure there is sufficient air circulation around the Scape® Tangible.
·Make sure all the ventilation holes on around the screen are uncovered.
Excess voltage from lightning strikes
In the event of a thunderstorm there is a risk of excess voltage damage from lightning strikes electrical appliances that
are plugged in.
·Do not install the Scape® Tangible during a thunderstorm.
·Disconnect the devices from the mains during thunderstorms.
Moisture, liquid and steam
Moisture, liquids and steam inside the Scape® Tangible can cause electric shocks or short circuits.
·Only use the Scape® Tangible indoors.
·Do not allow liquids to get inside the Scape® Tangible.
·Protect your Scape® Tangible from steam and moisture.

1. General
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 5 of 27 poc: SFi
Improper cleaning
Improper cleaning with harsh detergents and solvents or soaking wet cloths can damage the Scape® Tangible.
·Observe the information on cleaning your Scape® Tangible (chapter 1.3 Cleaning instructions).
Improper opening and repair
Improper opening and improper repairs may be dangerous to users of the device.
·Do not open the housing of the device.
·In case of repair contact the manufacturer or a specialist dealer.
Radio interference
Radio interference can be generated by any device that emits electromagnetic signals. Due to the large number of
devices that transmit and receive radio waves, interference from overlapping radio waves can occur.
·Do not use the Scape® Tangible in locations where the use of radio equipment is prohibited.
·Always follow the instructions and instructions of authorized persons to switch off radio equipment, especially in
hospitals, outpatient health centers, medical practices and other medical facilities, to avoid interference with sensitive
medical equipment.
·Check with your doctor or the manufacturer of your medical device (pacemaker, hearing aid, implant with electronic
control, etc.) to see if it can work your Scape® Tangible without interference.
·If necessary, maintain the minimum distance of 15 cm recommended by medical device manufacturers to avoid
interference with your medical device.
Hazardous environments
Under unfavorable conditions, radio waves near explosive atmospheres may lead to fire or explosions.
·Do not install and operate the Scape® Tangible near explosive gases, flammable gases, areas where the air contains
chemicals or particles such as grain, dust or metal powders, and near detonation zones.
·In places with potentially explosive gases and near detonation zones, follow the instructions for switching off the
electronic devices to avoid disruption of the blasting and ignition systems.
Load and damage to the surface
Rough, hard or sharp-edged materials and heavy objects can damage the screen surface of the Scape® Tangible.
·Do not place heavy objects on the screen.
·Use only objects with smooth or soft bottom surfaces on the screen.
·Clean the undersides of the objects before and after each use.
·The glass surface protrudes 1.5 mm on each side. Never place the Scape® Tangible on its edge. When storing vertically
and during transport, make sure that the device is packed in its original packaging or packaging that is equally soft.

1. General
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 6 of 27 poc: SFi
1.2. Scope of delivery
The following accessories are included with your Scape® Tangible:
·Power cord for connection to the mains
·Network cable for connection to a local network
·USB cable for direct connection to a PC
·Infrared remote control (receiver on the back of the device)
·Screw cover
·Screen cleaning kit
·Operating instructions (possibly by email)
1.3. Cleaning instructions
The touch sensor of the Scape® Tangible does not usually need to be serviced. Nevertheless, it is recommended to
clean the glass surface of the screen regularly.
·Disconnect the device from the mains before cleaning.
·Typically, a solution of isopropyl alcohol and water (50:50 blend ratio) or the included screen cleaning kit are best for
cleaning the touch sensor.
·Apply the solution to a soft, lint-free cloth. Avoid using rough cloths.
·Use the cloth to clean the glass surface. Apply the liquid only to the cloth and never directly to the device. This will
prevent liquid from entering the inside of the device or causing marks on the frame.
1.4. Transportation instructions
The safest way to transport your device is in a Scape® Tangible flight case (sold separately).
·Transport the device upright.
·Do not transport the device upside down.
·Secure the device against slipping and tilting.

2. Specifications and set up
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 7 of 27 poc: SFi
2. Specifications and set up
2.1. Specifications
2.2. Connections and controls
*analogue to button on remote control
Screen
3840 x 2160 (UHD)
60 Hz
1
.07 billion colors
6 ms response time
Connections
2x HDMI
2.0, 1x HDMI 1.4
1x DisplayPort 1.4
Touch
sensor
3M
– PCAP (80 touches)
(optional) integrated Capore® Touch & Object Recognition
1
IR-Sensor for remote control
2
Switch between Touch TUIO / USB Touch
3
RJ
-45 Lan interface – to use the
Capore® Touch & Object Assistant
4
USB-Connection Type B – for direct connection of touch and PC
5
Line Out Output
6
DisplayPort 1.2 input
7
2x HDMI 2.0 input (UHD 60 Hz)
8
HDMI 1.4 input
9
Stand
-by *(17)
10
Status
LED
11
Close OSD / > back / > show input selection
*(21)
12
Plus /
Right *(23)
13
Minus / Left
*(22)
1
4
Open
OSD / confirm selection *(20)
1
2
3
4
5
6
7
8
9
10
11
12
13
14

2. Specifications and set up
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 8 of 27 poc: SFi
2.3. Remote control
*analogous to buttons on the screen
All keys on the remote control which are not explained above are not required for operation of Scape® Tangible and do
not have any function.
1
5
IEC socket for connection to 230V 50Hz
16
Main power switch
17
Stand-by
*(9)
18
Display mode selection
19
Show input-selection
20
Show OSD / confirm selection
*(14)
21
Close OSD
*(11)
22
Left / Minus
*(13)
23
Right / Plus
*(12)
15
16

3. Installation
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 9 of 27 poc: SFi
3. Installation
The Scape® Tangible is approved for upright or hanging operation as well as for horizontal operation.
When the screen is suspended, secure the screen against falling using the metal eyelets mounted on the upper side if
possible.
If necessary, you can unscrew the metal eyelets and insert the supplied screw covers.
The Scape® Tangible may only be operated at a tilt angle of 0 - 90°.
The Scape® Tangible comes with VESA compatible threaded holes. The monitor can be mounted in a landscape format
by using these holes.
For mounting with VESA brackets, use a suitable wall bracket with a load equivalent to the weight of the monitor. To
attach the VESA mount you must use 4 M6x25 metal screws.
VESA formats:
MIS-F 400 x 400 mm (M6)
MIS-F 600 x 400 mm (M6)
MIS-F 800 x 400 mm (M6)

3. Installation
—
Scape® Tangible Technical specifications are
st55-005 to change without notice.
Operating manual Version 1.6 – Status: 12/2019
Page 10 of 27 poc: SFi
3.1. Ventilation guide
This ventilation guide applies for trouble-free operation under normal conditions. In adverse environments, such as high
temperature, polluted air, or high humidity, special precautions should be taken that are not covered in this document.
For ventilation, the Scape® Tangible has 6 fans on the rear – 3 for taking air in and 3 for blowing air out. Both inlet and
outlet sides move 0.5 m³ air / min.
Front:
Underside (front above):
__________________________________________________
blue: cold incoming air | red: warm outgoing air