Intermatic Fl150mh User manual

Figure 1 Figure 2

Mounting

Arm BoltLocknut

Lens

Door

Screw

Reflector

Screw

Lampholder

Install with Lamp vertical

HID Flood Light - FL Series

INSTALLATION INSTRUCTIONS

Lamp Types: Metal Halide 150 Watt & 175 Watt

Model: FL150MH & FL175MH

FOR OUTDOOR USE ONLY

NOT FOR USE IN HAZARDOUS ATMOSPHERES

IMPORTANT: Read instruction sheet carefully before installing fixture.

Retain instructions for future reference.

ELECTRICAL REQUIREMENTS

A qualified electrician should complete all required wiring. This fixture will accept 120, 208, 240 or 277

Volts AC and must be properly grounded for safety. A mounting suitable for outdoor use and rated for

wet locations is required. Follow all applicable electrical codes and regulations.

WARNING:

Electric shock hazard

Disconnect power at circuit breaker or fuse box before installing or servicing light.

WARNING:

Fire hazard

USE MIN 60˚C SUPPLY CONDUCTORS.

CONNECT TOSUPPLY IN EXTERNAL JUNCTION BOX ONLY.

Lamp and housing become very hot during use.

Ensure free air circulation around unit to dissipate heat.

Avoid enclosed locations and locations where flammable debris (leaves, cut grass, etc.) might collect.

Avoid locations where humans or animals might accidentally touch fixture.

WARNING:

Explosion hazard

Never operate light without securing the lens door. When light is operating, the gas in the

lamp inner arc tube is at high pressure.

Never operate light if the fixture lens or outer glass envelope of the lamp is broken or missing.

WARNING:

Explosion hazard

Wear safety glasses and gloves when handling lamp. Metal Halide outer envelope is pressurized

and could explode if broken.

WARNING: UV hazard (Metal Halide Lamps Only)

The type of lamp used in this fixture can cause serious skin burn and eye inflammation from short

wave ultraviolet radiation if outer envelope of the lamp is broken or punctured, and the arc tube

continues to operate. Do not use where people will remain for more than a few minutes. Certain

types of lamps that will automatically extinguish when the outer envelope is broken or punctured are

commercially available.

MOUNTING & WIRING

1. Screw the threaded mounting arm of the fixture into 1/2” NPS mounting hole on mounting device.

Metal Halide 150 Watt

Figure 3

277 V

240 V

208 V

120 V

COM

IGN-01

LAMP

COM

CAP

277 V

240 V

208 V

120 V

COM

LAMP

COM

Metal Halide 175 Watt

Figure 4

2. Using provided twist on or other approved connectors, connect the fixture wires to the supply wires as follows:

(See Figure 3 or Figure 4)

a. Identify supply voltage.

b.Open lens door and remove reflector.

c. Select appropriate fixture wire to match incoming voltage. All fixtures are shipped with

appropriate twist on wire connector and strip fixture wire marked with matching voltage.

d. Confirm unused voltage fixture wires are appropriately capped within fixture body.

e. Feed the matching voltage fixture wire through the mounting arm.

f. Replace and secure reflector in the same orientation as shown in Figure 2.

g. Close and secure lens door to prevent damage while wiring fixture to mounting.

h. Connect the fixture wire matching the incoming voltage to the black (hot) supply wire.

i.Connect the fixture wire marked COM to the white (neutral) supply wire.

j. Connect the bare copper (fixture ground) wire to the supply grounding wire.

3. Make sure that all wires and connections are inside the mounting wiring compartment and that the cover is properly

sealed to keep moisture out.

4. Open lens door. Screw lamp into socket in lampholder until finger-tight.

5. Close lens door, making sure that gasket is in place and compressed to seal out moisture. To weatherproof fixture,

seal all holes in housing (mounting conduit, plugs, photocontrols, etc.) with silicone sealant.

6. To operate, restore power to the circuit and switch light on.

CAUTION:

(Metal Halide Lamps Only) Do not use lamp beyond

manufactures rated life to reduce chance of lamp rupture.

Turn lamp off at least once for 15 minutes per week to reduce

chance of lamp rupture.

AIMING FIXTURE

WARNING:

Electric shock hazard.

Do not turn mounting arm more than 360˚ after wires are connected. Excessive twisting of wires

may loosen connections.

1. Turn off power at circuit breaker or fuse box. Rotate mounting arm until light is pointing in the

desired direction. Tighten locknut to secure.

2. Loosen mounting arm bolt (do not remove) and tip fixture to desired angle. Retighten bolt to secure.

3. Turn power on and check aim. If adjustment is needed, turn power OFF at circuit breaker or fuse

box and allow fixture to cool before adjusting

LAMP REPLACEMENT

CAUTION:

Use lamp of correct type and wattage as specified on fixture.

1. Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.

2. Release retaining clip and swing hinged fixture lens door open . Remove old lamp and replace

with new lamp of correct type and wattage. Screw lamp into socket in lampholder until finger-tight.

3. Close and secure lens door, making sure that gasket is properly seated, free of debris, and

compressed to seal out moisture.

4. Turn power back on.

5. Properly dispose of lamp per manufacturer’s recommendations.

LIMITED 1 YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended

to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been

subject to unauthorized repair,opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the

finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOTALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-

TIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES,

INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED

WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATEDABOVE. SOME STATES DO NOTALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE

ABOVE LIMITATION MAYNOT APPLY TO YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage

prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com

Please be sure to wrap the product securely to avoid shipping damage.