Intex Marketing CHALLENGER 3/SET User manual

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
98A
098-*A*-R0-2106
INTEX® OWNER’S MANUAL
INFLATABLE BOAT
ISO-6185 BOAT DESIGN CATEGORY D
Due to a policy of continuous product improvement, Intex reserves the right
to change specications and appearance, which may result in updates to
the instruction manual without notice.
IMPORTANT
THIS BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. READ IT THOROUGHLY BEFORE USING
THIS PRODUCT AND KEEP IT FOR FUTURE REFERENCE.
©2020 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous
droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten. Printed in China/Imprimé en Chine/
Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains
pays sous licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen
verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd.,
G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed
in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der
Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 2
98A
TABLE OF CONTENTS
INTRODUCTION.............................................................................................3
MANUFACTURE’S CERTIFICATION.............................................................3
SAFETY & WARNING..............................................................................
.......
3
MANUFACTURER’S RECOMMENDATION...................................................4
DESCRIPTION................................................................................................5-7
INFLATING INSTRUCTIONS............................................................
............
..8
HOW TO USE BOSTON VALVE....................................................................8
SEAT INSTALLATION............................................................................
.........
9
FISHING ROD HOLDER USE..............................................
...........................
9
OAR ASSEMBLY................................................................
............................
9-10
GRAB LINE INSTALLATION..................................................
........................
11
ACCESSORY LINE INSTALLATION................................................
............
..11
SAFETY AND OPERATION INSTRUCTIONS...............................................11-12
CARE AND MAINTENANCE..........................................................................12
DISASSEMBLY AND STORAGE................
....................................................
13
TROUBLESHOOTING................................................
.....................................
13
REPAIRS.................................................................
........................................
13
LIMITED WARRANTY.......................................................
.............................
.14

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 3
98A
• This is not a life saving device. Use only under competent supervision. Never allow diving into this
product. Never leave in or near the water when not in use. Never tow from any vehicle.
• Read the complete Owner’s Manual before use and store this Manual in a safe place for future
reference.
• Follow all the Safety and Operating Instructions on this Manual.
• TYPE II, inflatable boats capable of taking an outboard motor. Motors are not to exceed the
maximum recommended power and weight.
•
Rotating propeller may cause serious injury or death. Shut off engine when near persons in the water.
• Read the instruction of outboard motor for correct installation and operation.
• Bewareofoffshorewindsandcurrents. Never navigate alone.
• Do not exceed the maximum recommended capacities. Overloading violates regulations.
• Everyone on board must wear a Personal Floatation Device (PFD).
• Use caution when stepping or climbing aboard the boat. Step into the center of the boat for
maximum stability.
• Distribute the weight of passengers, gear, tackle box, and accessories so that the boat sits level
fore (front) to aft (back) and side-to-side.
• Do not use your boat if you suspect a puncture or leak.
• Adults should inflate the chambers in numbered sequence.
• Not for white water rafting or any other extreme sports activities.
• Not for commercial or rental use.
• Follow these rules to avoid drowning, paralysis or other serious injuries.
WARNING
Introduction
This manual has been compiled to help you to operate your craft with safety and
pleasure. It contains details of the craft, the equipment supplied or fitted, its systems,
and information on its operation and maintenance. Please read it carefully, and familiarize
yourself with the craft before using it.
If this is your first craft, or you are changing to a type of craft you are not familiar with, for your
own comfort and safety, please ensure that you obtain handling and operating experience
before assuming command of the craft. Your dealer or national sailing federation or yacht club
will be pleased to advise you of local sea school, or competent instructors.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW
OWNER WHEN YOU SELL THE CRAFT. RECORD THE “WATERCRAFT IDENTIFICATION
NUMBER” (WIN) WHICH IS PRINTED ON THE BOAT’S HULL IN THE FOLLOWING BOX:
Manufacture’s Certification
For boats between and including 2.5 and 24 meters hull length, a CE (FOR EUROPE ONLY)
mark means that the boat complies with European Directives for Recreational Craft 2013/53/
EU as published by the International Organization for Standardization, ISO 6185.
NMMA (FOR USA ONLY) certification means that the boat, sold in the United States, has
been judged by the National Marine Manufacture’s Association to be in compliance with the
U.S. Coast Guard Regulations and American Boat and Yacht Council (ABYC) standards and
recommended practices.
Safety
WIN: ______________
Boat Design Category D -“SHELTERED WATERS”-: Designed for voyages on sheltered coastal
waters, small bays, small lakes, rivers and canals when conditions up to, and including, wind force
4 and significant wave heights up to, and including, 0.3 m may be experienced, with occasional
waves of 0.5 m maximum height, for example from passing vessels.

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 4
98A
+ +
CHALLENGER 3 / SET
SEAHAWK 2 / SET
SEAHAWK 3 / SET
SEAHAWK 4 / SET
EXCURSION 4 / SET
EXCURSION 5 / SET
MARINER 3 / SET
MARINER 4 / SET
II
II
II
II
II
II
II
II
2.95
2.36
2.95
3.51
3.15
3.66
2.97
3.28
1.37
1.14
1.37
1.45
1.65
1.68
1.27
1.45
1.5
1.5
1.5
1.5
1.5
1.5
2
3
320
240
360
480
500
600
400
500
3
2
3
4
4
5
3
4
9
6
11
17
19
22
25
32
0.035 (0.5)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.069 (1.00)
0.080 (1.14)
0.080 (1.14)
MODEL TYPE
Unladen Craft Weight
mm HP Kg Kg
bar (psi)
LhBh
TABLE A
Manufacturer’s Recommendation
The total number of persons, motor power and total weight shall not exceed the limits
printed on the boat. Please refer to the boat's hull label for the actual values of your
boat. See Table A.
BOAT LABEL FORMAT
ISO 6185 PART 1 TYPE
CATEGORY D
Do not overinflate or use high pressure air compressor to
inflate. Adults should inflate the chambers with cold air in
numbered sequence.
Use the enclosed ruler to check while inflating.
Nicht zu stark aufblasen und keinen Kompressor zum
Aufblasen verwenden.
Erwachsene sollten die kammern in der angegebenen
Reihenfolge mit kalter luft aufblasen.
Verwenden Sie das beigefügte Lineal um die korrekte Füllung
zu überprüfen.
Ne pas surgonfler. Ne pas utiliser de compresseur pour le go
flage. Le gonflage doit être effectué par un adulte avec de l'air
froid en suivant les étapes suivantes.
Utiliser la règle jointe pour ajuster le gonglage de la chambre à
air principale.
MAXIMUM CAPACITIES
MAXIMUM-KAPAZITÃT
CAPACITÉS MAXIMUM
MAXIMUM POWER
MAXIMUM MOTORKRAFT
PUISSANCE MAXIMUM
PERSONS
PERSONEN
PERSONNES
MANUFACTURER
HERSTELLER
FABRICANT
MODEL
MODELL
MODÈLERECOMMENDED WORKING PRESSURE FOR EACH CHAMBER
EMPFOHLENE ARBEITENDE DRUCK FÜR JEDE LUFTKAMMER
RECOMMANDÉ FONCTIONNEL PRESSION POUR CHAQUE CHAMBRE À AIR
BY INTEX®
____________________
= ___ bar ( ___ psi)
CHINA
3
5
6
7
8
2
1
+ + = ___ Kg ( ___ Lbs)
___kW (___HP) / ___Kg (___Lbs)
= ___
4
9
10
LOAD CAPACITY (BASIC FLOTATION)
CAPACITÉ DE CHARGE (FLOTTAISON DE BASE) ___Kg ( ___ Lbs) MAX.
Certified by the National Marine Manufacturers Association using ABYC standards
Certifié par la National Marine Manufacturers Association en utilisant les normes ABYC
MAXIMUM CAPACITIES / CAPACITÉS MAXIMALES
PERSONS OR ____kg (___Lbs) / PERSONNES OU ___KG
____ POUNDS, PERSONS, GEAR / ___KG, PERSONNES ET ÉQUIPEMENT
DESIGN COMPLIANCE WITH NMMA REQUIREMENTS BELOW IS VERIFIED. MFGR. RESPONSIBLE FOR PRODUCTION CONTROL
LA CONFORMITÉ DU DESIGN AVEC LES EXIGENCES NMMA EST VÉRIFIÉE. MFGR. RESPONSABLE DU CONTRÔLE PRODUCTION.
CN- XEE
ISO-6185 boat design category (certain models). CE mark (for Europe only) (certain models).
Manufacturer’s recommended maximum load capacity.
Maximum motor power and motor weight.
Maximum person’s capacity.
Manufacturer’s name and country of origin.
Model name and number.
Manufacturer’s recommended working pressure.
NMMA (for USA only) certification means that the boat, sold in the United States, has been judged by
the National Marine Manufacture’s Association to be in compliance with the U.S. Coast Guard
Regulations and American Boat and Yacht Council (ABYC) standards and recommended practices.
Watercraft identification number (WIN).
9
8
7
6
5
3
2
1
4
10

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 5
98A
" " - Recommended seating arrangement of the occupants.
Description
Challenger Series
3 51 8 102 46 11
" " - Recommended seating arrangement of the occupants.
Seahawk Series
Challenger 3 / Set
Seahawk 2 / Set
1 8724 5 6 109 11 1 8 1072 946 11
3 5
Seahawk 4 / Set
36
1 972 84 5 1110
Seahawk 3 / Set

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 6
98A
" " - Recommended seating arrangement of the occupants.
Excursion Series
Excursion 5 / Set
142 6 79 1053 11
142 6 79 1053 11
Excursion 4 / Set

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 7
98A
NOTE: Only use Intex Motor Mount Kit (#68624).
Drawings for illustration purpose only. Actual product may vary. Not to scale.
Grab handle
All around grab line
Seat or seat cushion
Inflatable floor or removable slats floor
Oar lock
Oar holder
Gear pouch or accessory bag
Inflation valve / Keel valve
Fishing rod holder
Motor mount
Boston valve
Rock guard
Inflatable keel
1
2
3
4
5
6
7
Descriptions
8
9
10
11
12
13
" " - Recommended seating arrangement of the occupants.
Mariner 4 / Set
6
89
11
13 4 57
2
12 13
10
Mariner 3 / Set
12 13
1
11
3
86
5
710
24
9

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 8
98A
Inflating Instructions
Before starting, locate a clean area free of stones or other sharp objects. Unroll the
boat so it is laid out flat, and locate your pump.
Use a hand or foot operated air pump to inflate the boat. Do not use high-pressure air
compressors. Adults should inflate the chambers following the numerical sequence marked
on the valves. It is very important to follow the numerical sequence; failure to do so will
result in an improperly inflated boat. Fill each chamber until it is stiff to the touch but NOT
hard. Use the enclosed ruler to check the main chamber for proper inflation. DO NOT OVER
INFLATE. Fill with cold air only.
IMPORTANT: Air temperature and weather condition do affect the internal air pressure of
inflatable products. In cold weather the product will lose some pressure due to the fact that
the air will contract. If this occurs, you may want to add a little air to the product. However,
in hot weather, the air will expand. You must let some air out to prevent the product from
failing due to overpressure.
How to Use Boston Valve:
1. Double valve cap (valve lets air in, not out).
2. Quick deflation cap.
3. Unscrew Double valve cap.
4. Insert output end of air pump into valve and fill. Do not over inflate or use high pressure
compressor.
5. To deflate: unscrew quick-deflation cap. CAUTION: Double valve does not operate when
this cap is off. Do not unscrew this cap while boat or inflatable is in water.
Challenger series / Seahawk series / Excursion series:
1
23
45
12
3
4
5
Mariner series:

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 9
98A
Seat Installation (Certain Models):
1. Inflate each seat cushion slowly to about 75% of its capacity.
2. Attach the seat cushion hinge to the hinge on the boat. Repeat the
connection on the other side and for all seats. See Fig A.
3. Finish inflating the seat cushions slowly until it is firm to the touch
but NOT hard. DO NOT OVER INFLATE!
4. To disassemble the seats, deflate the seats first and reverse the
installation procedures.
NOTE: Some seat cushions after inflation are tuck in directly into
the fore, mid or aft locations of the boat cockpit. No hinges.
Mariner
series
:
1. Inflate each seat cushion slowly to about 75% of its capacity.
2. Put the seat cushions into the fore, mid or aft locations of the boat cockpit.
3. Finish inflating the seat cushions slowly until it is firm to the touch but NOT hard. DO NOT
OVER INFLATE!
4. Seat cushions after inflation are tuck in directly into the fore, mid or aft locations of the boat
cockpit.
5. To disassemble the seats, deflate the seats first and reverse the installation procedures.
Fishing Rod Holder Use (Certain Models):
1. Slide the end cap over the end of the fishing rod.
2. Insert the fishing pole into the holder.
Mariner
series
:
1. Slide the fishing rod holder into the mounting base.
2. Insert the end cap into the fishing rod holder.
3. Insert the fishing rod into the end cap.
Oar Assembly:
1. Insert “Shaft A” with the pin end first into the blade. Make sure the pin is securely fastened to
the blade.
2. Insert the assembled “Shaft A” through the oar-lock with the blade towards outboard (water).
3. Place the retainer ring onto the other end of “Shaft B”, from inside of the boat.
4. Press the pin and insert shaft B into shaft A, make sure the pin is securely snapped into the
hole.
5. When the oars are not in use secure the oars onto the oar holders located on each side of
the boat.
Fig A
Shaft A
Pin
Pin
Shaft B
Blade
Retainer Ring
Fishing
Rod Holder
End Cap
Fishing
Rod
Mounting base
Fishing
Rod Holder
End Cap
Fishing
Rod

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 10
98A
FOR MARINER 3 & 4:
FRENCH OARS:
3. 4.
1. 2.
Shaft B
Shaft A
Pin
Blade
1
2
3

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 11
98A
Grab Line Installation (Certain Models):
IMPORTANT: To properly install the inflatable boat’s grab line and/or accessory lines,
first inflate the boat.
If is necessary, begin the grab line installation at the
rear of the boat by threading it through the rope holders
completely around the outside of the boat. Tie the two
loose ends in a square knot at the rear end of the boat.
Accessory Line Installation (Certain
Models):
Your boat may have accessory lines to
install. Tie a figure eight knot into one end
of the accessory line and slide it through the
rope holders. Tie a figure eight knot in the
remaining end of the rope.
The accessory bags may or may not be
attached to the accessory lines. Slide the
rope through the accessory bags while
installing the accessory lines, if desired.
Safety and Operating Instructions
Before Departing from the Shore or Dock
Know all required information and inform your passengers:
• Take a boating safety course and get hands-on training from your boat dealer or local
boating authorities.
• Know all local regulations and hazards related to water activities and boat operation.
• Check weather forecast, local currents, tides and wind conditions.
• Advise someone on land of the time you plan to be back at your starting point.
• Explain basic boat operation to all passengers.
• Children and non-swimmers need special instructions in the use of life jacket or personal
floatation devices (PFD).
• Be sure that one of your passengers can operate the boat in case of emergency.
• Learn how to determine the distance you can cover, and remember that bad weather
conditions can alter this.
• Review all safety requirements regularly.
Check the working condition of the boat and equipments:
• Check inflation pressure.
• Inspect the valves caps.
• Check the load is evenly distributed, fore (front) to aft (back) and side-to-side.
Make sure that all required safety equipment is on board (check the laws and
regulations of the country or locality in which you are boating to see if additional
equipment may be needed):
• One personal flotation device (PFD) per person.
• Air pump, oars, repair kit and tool kit.
• Any other mandatory equipment.
• The boat papers and your boating license (if applicable).
• Lights are required if operating after dark.
Figure eight knot
Square knot

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 12
98A
Rules to Observe During Navigation
•Be responsible, do not neglect the safety rules, this could jeopardize your life and
the lives of others.
•Always keep control of your boat.
•Respect local regulations and practices.
•Near the shore, navigate in the designated boating area.
•Remember that weather conditions can rapidly deteriorate. Always be sure that you can
reach a shelter rapidly.
•Everyone on board must always wear a personal flotation device (PFD).
•Do not drink alcohol or take drugs before or while operating your boat. Maintain passenger
sobriety.
•Do not exceed the authorized number of persons or weight.
•Make sure your passengers remain seated at all times. At planning speeds, in rough water
or during sharp turns, all passengers should position themselves in seats or on the floor.
• No bow riding. Bow riding is illegal in most areas and is extremely dangerous. In case of
falling, the man overboard is in the way of the propeller.
• Be especially careful when docking. Arms and legs may be injured if they are outside the
boat.
• Keep clear of swimmers and divers. Always avoid areas where divers/swimmers are in the
water.
• Keep a sharp lookout especially when operating near beaches and launch sites. The Alpha
flag indicates proximity of divers. You MUST maintain a safe distance as required by your
local boating laws, which may range from 50 meters (164 feet) to 91 meters (300 feet).
• Avoid sharp turns at high speeds. You could get ejected from the boat.
• Do not make changes in direction without advising passengers.
• Avoid all contact between the buoyancy tubes and sharp objects or aggressive liquids
(such as acid).
• Do not smoke on board. Most importantly while filling the fuel tank.
• Any fuel spilled must be cleaned and disposed of according to local laws and regulations.
Reboarding your boat
All around grab line is provided to assist with reboarding the boat. Grabbing the line and
pulling yourself inside the cockpit is easiest to perform over the port and starboard (left and
right) sides of the boat. Pay attention to all safety information and warnings on your boat and
never approach the boat from the stern (back side) when a motor is installed.
Care and Maintenance
The boat is made of the highest quality materials and complies with ISO 6185 standards.
Altering the construction of the boat will endanger your own safety, safety of the occupants
and void the limited warranty!
There is very little that you have to do to keep your boat in good condition for many years.
You may store it inflated or deflated. If you leave it outside, raise it up off the ground and do
not place any heavy or sharp objects on it. If it is going to be in direct sunlight or exposed to
leaves or rain, cover it with a tarp. We do not recommend hanging the boat. If you store it in
a closet, basement or garage, we suggest you pick a cool, dry place, making sure the boat is
clean and dry before you store it - or mold can accumulate.
Use as few cleaning agents as possible, do not discharge waste agents into water, and clean
your boat preferably on land.
Clean your boat after a trip to prevent damage from sand, salt water or sun exposure.
Most dirt can be removed with a garden hose, a sponge and mild soap. Make sure the boat
is completely dry before storing. Store the product and accessories in a dry, temperature
controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit
(40 degrees Celsius) storage location.

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 13
98A
Disassembly and Storage
First clean your boat thoroughly following the Care and Maintenance instructions.
Open all air valves and deflate boat completely. Remove all the accessories from the
boat; seats, fishing rod holders, oars, gear pouch and battery pouch.
Fold the left and right chambers of the boat towards the middle of the floor. It is not
necessary to remove the slats to fold the boat. Fold the bow end twice to the middle of the
boat tightly while forcing out any remaining air; repeat this procedure for the stern. With two
opposing folded sides, fold one end over the other like closing a book. Replace all inflation
valve caps. Your boat is ready for storage. Fold the boat loosely and avoid sharp bends,
corners and creases which can damage the boat.
Troubleshooting
If your boat appears a bit soft, it might not be because of a leak. If the boat was inflated late
in the day with 32°C (90°F) air, that air might cool down to 25°C (77°F) overnight. The cooler
air exerts less pressure on the hull, so it could appear soft the next morning.
If there has been no temperature variation, you need to start looking for a leak:
• Take a good look at your boat from just a few feet away. Flip it over and closely check
over the outside. Any large leaks should be clearly visible.
• If you have an idea where your leak is, use a mix of dishwashing liquid and water in a
spray bottle, and spray over the suspicious areas. Any leak will produce bubbles that will
pinpoint the location of the leak.
• Check valves for leak, if necessary, spray soapy water around the valve and the valve
base.
Repairs
Through constant use you may occasionally puncture your boat. Most leaks only take a few
minutes to repair. Your boat comes with a repair patch, and additional repair supplies can be
ordered from Intex Consumer Service or from our website.
First locate the leak; soapy water will bubble out from the source of the leak. Thoroughly
clean the area surrounding the leak to remove any dirt or grime.
Cut a piece of repair patch large enough to overlap the damaged area by approximately
1.5 cm (1/2”). Round off the edges, and place the patch on the damaged area and press
down firmly. You may want to use a weight on top to keep it in place.
Do not inflate in 30 minutes after patching.
If the patch does not hold, you can purchase a PVC or silicon based glue for repairing
camping mats, tents or shoes from your local market to patch your boat, please refer to the
instruction of the glue for patching.

(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875” X 7.25” 06/17/2020
SAVE THESE INSTRUCTIONS
Page 14
98A
Limited Warranty
Intex Inflatable Boat
Your Intex Inflatable Boat has been manufactured using the highest quality materials and
workmanship. All Intex Inflatable Boats have been inspected and found free of defects prior
to leaving the factory. This limited warranty applies to the Intex Inflatable Boat only.
This limited warranty is in addition to, and not a substitute for, your legal rights and remedies.
To the extent that this warranty is inconsistent with any of your legal rights, they take priority.
For example, consumer laws across the European Union provide statutory warranty rights in
addition to the coverage you receive from this limited warranty: for information on EU-wide
consumer laws, please visit the European Consumer Center website at http://ec.europa.eu/
consumers/ecc/contact_en/htm.
The provisions of this limited warranty apply only to the original purchaser. This Limited
Warranty is valid for a period of 90-days from the date of purchase. Keep your purchase
information with this document, as proof of purchase will be required and must accompany
warranty claims or the limited warranty will be invalid.
If you find a manufacturing defect in the Intex Inflatable Boat during the warranty period,
please contact the appropriate Intex Service Center listed in the separate “Authorized Service
Centers” sheet. If the item is returned as directed by the Intex Service Center, the Service
Center will inspect the item and determine the validity of the claim. If the item is covered by
the provisions of the warranty, the item will be repaired or replaced, with the same or
comparable item (at Intex’s choice) at no charge to you.
Other than this warranty, and other legal rights in your country, no further warranties are
implied. To the extent possibly in your country, in no event shall Intex be liable to you or any
third party for direct or consequential damages arising out of the use of your Intex Inflatable
Boat, or Intex or its agents’ and employees’ actions (including the manufacture of the
product). If your country does not allow the exclusion or limitation of incidental or
consequential damages, this limitation or exclusion does not apply to you.
You should note that this limited warranty does not apply in the following circumstances:
• If the Intex Inflatable Boat is subject to negligence, abnormal use or application, accident,
improper operation, trailering or towing, improper maintenance or storage;
• If the Intex Inflatable Boat is subject to damage by circumstances beyond Intex’s control,
including but not limited to, punctures, tears, abrasions, or ordinary wear and tear;
• To parts and components not sold by Intex; and/or
• To unauthorized alterations, repairs or disassembly to the boat by anyone other than Intex
Service Center personnel.
Read the owner’s manual carefully and follow all instructions regarding proper operation and
maintenance of your Intex Inflatable Boat. Always inspect your equipment prior to use. This
limited warranty will be void if use instructions are not followed.
RECORD THE OWNER’S NAME, ADDRESS, PHONE NUMBER AND WIN BELOW:
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020
©2020

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020
”

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020
3
2
®
3
2

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020

98
IO
(98IO) “ISO” BOAT W / MOTOR MOUNTING (TYPE II) BULGARIAN 7.5”X10.3” 09/21/2020
This manual suits for next models
7
Table of contents
Languages:
Popular Boat manuals by other brands

Blackfin
Blackfin 222 Center Console owner's manual

Sea Eagle
Sea Eagle 9 Instruction & owner's manual

Sea Eagle Boats
Sea Eagle Boats SUPCat10 Instruction & owner's manual

Cobalt Digital Inc
Cobalt Digital Inc 220S owner's manual

Gumotex
Gumotex SOLAR user manual

Wehncke
Wehncke Amazonas operating instructions