Intex Saltwater System CS8111 User manual

133
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
OOWWNNEERR’’SSMMAANNUUAALL
Krystal Clear
Saltwater System®
& Filter Pump
Model CS8111
IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
IIMMPPOORRTTAANNTT!!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
133-***-R1-1211
For illustrative purposes only.

133
SAVE THESE INSTRUCTIONS Page 2
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
TTAABBLLEEOOFFCCOONNTTEENNTTSS
Warnings......................................................................... 3
Parts List & References................................................. 4-9
Product Information & Specifications.......................... 10
Setup Instructions.......................................................... 11-14
Salt & Pool Water Volumes............................................ 15
Intex Pools Salt Table..................................................... 16
Intex Pools Operating Time Table................................. 17
Intex Pools Cyanuric Acid Table................................... 18
Non-Intex Pools Salt Table............................................. 19
Non-Intex Pools Operating Time Table......................... 19
Non-Intex Pools Cyanuric Acid Table........................... 19
Operating Instructions................................................... 20-22
LED Code Chart............................................................. 23
Maintenance................................................................... 24-27
Long Term Storage......................................................... 27
Pool Maintenance and Chemical Definitions.............. 28
Troubleshooting Guide.................................................. 29-31
General Aquatic Safety.................................................. 32
Limited Warranty............................................................ 33
Intex Service Center Locations.................................... 34

133
SAVE THESE INSTRUCTIONS Page 3
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSAAFFEETTYYRRUULLEESS
This product is for use with storable pools only. Do not use with
permanently-installed pools. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such
that it cannot be readily disassembled for storage.
CAUTION
WARNING
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
•To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
•Children must stay away from this product and electrical cord(s).
•Assembly and disassembly by adults only.
• Risk of electric shock. Connect only to a grounding type receptacle, this product
is provided with a ground-fault circuit interrupter. If replacement of the plug or cord
is needed, use only identical replacement parts.
•Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The unit is provided with a ground-fault circuit interrupter (GFCI). To test the GFCI,
push the test button. The GFCI should interrupt power. Push the reset button, power
should be restored. If the GFCI fails to operate in this manner. The GFCI is
defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
•Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
•To reduce the risk of electric shock, replace damaged cord immediately. Use a
qualified electrician to replace the cord.
•To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
•Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
•Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI
since the ALCI will not protect people.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
•Do not operate this product when the pool is occupied.
• Never use the pool if indicated chlorine level is more than 3ppm.
• This product is intended to be used only for the purposes described in the manual!
• Operating this product without water flowing through the system can cause a build
up of flammable gases which can result in FIRE OR EXPLOSION.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.

133
SAVE THESE INSTRUCTIONS Page 4
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSSLLIISSTT
PARTS LIST
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
7
1
9
4 5
2
6
3
8
10 11 12
13 14 15

133
SAVE THESE INSTRUCTIONS Page 5
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
16 17 18
19 20 21
22 23 24
25 26 27
28 29 30
PARTS LIST (continued)
PPAARRTTSSLLIISSTT
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
* Optional
* Optional * Optional
* Optional
31 32 33

133
SAVE THESE INSTRUCTIONS Page 6
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSSRREEFFEERREENNCCEE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
1
2
3
4
5
68
7
1
2
10
9
8 12 13 12
14
15 16 17 30
18
11
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
33

133
SAVE THESE INSTRUCTIONS Page 7
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
REF. NO. DESCRIPTION QTY. SPARE PART
NO.
33 COPPER ELECTRODE NUT 1 11488
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2
2
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
VALVE O-RING
THREADED FILTER HOUSING COLLAR
FILTER HOUSING COVER
FILTER HOUSING O-RING
FILTER CARTRIDGE (59905)
AIR RELEASE VALVE B (WITH O-RING)
PUMP HOSE WITH NUTS
WATER TRANSFER HOSE (WITH COLLAR AND 2 HOSE CLAMPS)
SCREW
FLOW SENSOR
O-RING A
ELECTROLYTIC CELL WITH 2 SCREWS (O-RING A INCLUDED)
COPPER ELECTRODE
FLOW SENSOR CONDUIT
O-RING C
ANGLE JOINT (O-RING D INCLUDED)
O-RING D
10460
10264
10491
10490
11330
10725
10493
10726
10713
11460
10712
11233
11234
11251
10717
10724
10743
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
PPAARRTTSSRREEFFEERREENNCCEE
When ordering parts, be sure to quote the model number and part numbers.

133
SAVE THESE INSTRUCTIONS Page 8
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSSRREEFFEERREENNCCEE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
19
20
21 22 23 24 25
19
20
21 26 27 28
19
20
21 22 23 24
19
20
21 26 27 29

133
SAVE THESE INSTRUCTIONS Page 9
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSSRREEFFEERREENNCCEE
SPARE PART
NO.
10747 10262
10745
10256
10255 11235 11074 10722
11070 11071
11072
11131 19635
11254
QTY.
2 2
2
2
1
2 2 1
1
1
1
1
DESCRIPTION
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
HOSE O-RING
STEP WASHER STRAINER NUT FLAT STRAINER RUBBER WASHER THREADED STRAINER CONNECTOR ADJUSTABLE POOL INLET NOZZLE ADAPTOR B (OPTIONAL) STRAINER CONNECTOR (OPTIONAL) POOL INLET NOZZLE (OPTIONAL) STRAINER GRID (OPTIONAL) CELL COVER
CHLORINE TEST STRIPS
COPPER TEST STRIPS
REF. NO.
COMMON PARTS
19 20
21
30
31
32
LARGE AGP
22
23
24
25
SMALL AGP
26
27 28 29

133
SAVE THESE INSTRUCTIONS Page 10
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPRROODDUUCCTTIINNFFOORRMMAATTIIOONN//SSPPEECCSS
This product is specially designed for above ground pools. It will destroy the
bacteria, oxidize bather organics and control algae, which provide a safe, clean and
comfortable swimming pool.
Common salt (sodium chloride) is made up of two elements, sodium and chlorine.
During the installation of your Saltwater System/Filter Pump, a measured quantity
of salt is dissolved in the pool water to make it slightly salty. The pool water flows
through the saltwater system’s electrolytic cell to produce HCLO. The HCLO
dissolves in the water and instantly starts destroying bacteria and algae. It
also oxidizes all other organic materials.
Low voltage direct current is applied to the copper electrode, and copper ions are
generated and dissolved instantly in the water. Copper is an effective algaecide,
which will prevent algae from growing in the pool.
HOW SANITIZER IS GENERATED
Power: 110 - 120 Volt
Amperage: Saltwater System - 1.1 A; Filter Pump - 2.4 A
Wattage: Saltwater System - 125 W; Filter Pump - 275 W
Ideal Salt Level: 3000 ppm (parts per million)
Maximum Sanitizer Output/hour: 12 grams/hour
Copper Ionizer Output Current: 175 mA
Limited Warranty: see “Limited Warranty”
HOW COPPER IONS ARE GENERATED
PRODUCT SPECIFICATIONS
Flow Sensor
Electronic
Control Station
Electrolytic Cell
Water Outlet

133
SAVE THESE INSTRUCTIONS Page 11
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPPIINNSSTTRRUUCCTTIIOONNSS
STRAINER & PLUNGER VALVE SETUP
Strainer & Plunger Valve Setup (small AGP)
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:
1. Grasp the strainer and plunger valve mechanism.
2. In a counter-clockwise motion unscrew plunger valve union from the threaded
strainer connector (24). Be careful not to lose the step rubber washer (21).
3. Grasp the plunger valve assembly. Make sure the step washer (21) is in place.
Connect adaptor B (26) to plunger valve union.
4. Repeat steps 1 through 3 for nozzle and plunger valve mechanism.
5. Remove wall plug and then insert the strainer (27 & 29) into the lower position
of protruding hose connection, and the nozzle (27 & 28) into the upper position
of protruding hose connection. Adaptor B (26) fits over the strainer
connection (27) inserted into the connection.
6. Examine the plunger valve to see if the handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at the top and push down turning the
handle in a clockwise direction until the plastic protruding notch anchor is in
the "0/1" position. This will prevent water from flowing out during filling.
7. The pool liner is now ready to fill with water. Consult the above-ground-pool
owner's manual for filling instructions.
IMPORTANT
The Saltwater System/Filter Pump must be installed as the last piece of
pool equipment in the water return line to the pool. This location extends
the life of the titanium plates.
19
20
21 26 27 28
19
20
21 26 27 29

133
SAVE THESE INSTRUCTIONS Page 12
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPPIINNSSTTRRUUCCTTIIOONNSS
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:
STRAINER & PLUNGER VALVE SETUP (continued)
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (24) (see drawing 1).
Be careful not to lose the step rubber
washer (21). Place the plunger valve on the
ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (22) from the threaded
connector (24). Leave the flat washer (23)
on the connector (24).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector (24) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (22) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (22) back onto the threaded
connector (24) (see drawing 2).
5. Finger tighten the strainer nut (22) onto the
threaded connector (24).
6. Grasp the plunger valve assembly. Make
sure the step washer (21) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (24) (see drawing 3).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, grasp the handle at
the top and push down, turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling of the pool (see
drawings 4.1 & 4.2).
1
2
3
4.1
4.2
23 24
21
INSIDE
LINER WALL
INSIDE
LINER
WALL
22
2
1
1
2
1
2

133
SAVE THESE INSTRUCTIONS Page 13
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPPIINNSSTTRRUUCCTTIIOONNSS
NOZZLE & PLUNGER VALVE SETUP
1. Grasp the nozzle and plunger valve
mechanism.
2. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (24) (see drawing 5).
Be careful not to lose the step rubber
washer (21). Place the plunger valve on the
ground in a safe place.
3. In a counter-clockwise motion unscrew the
strainer nut (22) from the threaded
connector (24). Leave the flat washer (23)
on the connector (24).
4. Install the nozzle and plunger valve at the
upper position of the pool inlet. From the
inside of the pool liner insert the
connector (24) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
5. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (22) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (22) back onto the threaded
connector (24) (see drawing 6).
6. Finger tighten the adjustable pool inlet
nozzle (25) and the strainer nut (22) onto
the threaded connector (24).
7. Grasp the plunger valve assembly. Make
sure the step washer (21) is in place.
8. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (24) (see drawing 7).
9. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling of the pool (see
drawings 8.1 & 8.2).
10. Adjust the direction of the nozzle head
pointing away from the pool outlet for a
better circulation result (see drawing 9).
11. The pool liner is now ready to be filled with
water. Consult the above-ground-pool
owner’s manual for filling instructions.
5
7
8.1
8.2
INSIDE
LINER
WALL
POOL
9
2
1
1
2
1
2
6
23 24 25
INSIDE
LINER WALL
22
WATER
FLOW

133
SAVE THESE INSTRUCTIONS Page 14
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPPIINNSSTTRRUUCCTTIIOONNSS
SALTWATER SYSTEM/FILTER PUMP
Saltwater System/Filter Pump
1.Remove the Saltwater System/Filter Pump and hoses from the packaging.
2. Place the Saltwater System/Filter Pump in a location for hose (8) connections to
the plunger valve assemblies.
NOTE: Some regional regulations may require the filter pump to be
mounted on a stationary platform. There are two mounting holes located in
the pump base for this reason. Consult your local authorities for filter
pump mounting requirements.
3. Grasp the two pump hoses (8) and connect the hose nuts to the Saltwater
System/Filter Pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (3) from
the filter housing. Place it in a safe place.
5. The Saltwater System/Filter Pump is an airtight system. In a counter-clockwise
motion turn both air release valves (1 & 7) 1 - 2 turns to open. DO NOT remove
air release valves as water will expel with force if the motor is turned on
and injury may occur.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is
inside the housing. If yes, replace the cover, finger tighten the housing collar (3)
back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the
housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the electrolytic cell outlet to the
highest strainer assembly. You will find the hose connection at the bottom of the
plunger valve assembly. Use the hose nut to attach the hose.
9. Connect the second hose to the middle of the motor housing and to the
remaining liner connection.
IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open air
release valves, lift and lower the inlet hose until water starts to flow out of
the air release valves, close air release valves.

133
SAVE THESE INSTRUCTIONS Page 15
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSAALLTT&&PPOOOOLLWWAATTEERRVVOOLLUUMMEESS
SALT & POOL WATER VOLUMES
• Which kind of salt to use:
Use only Sodium Chloride Salts
Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also
acceptable to use water conditioning salt pellets (the compressed forms of
evaporated salt). However, it will take a longer time for them to dissolve. Do not
use iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to
the pool water and the electrolytic cell uses this salt to create the sanitizer. The
purer the salt the better the performance of the electrolytic cell.
• Optimum Salt Levels
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).
The optimal level is 3000 ppm.
A too low salt level will reduce the efficiency of the saltwater system and result in
low sanitizer production. A high salt level may generate a salty taste to the pool
water (this may occur at a salt level above 3500-4000ppm). Too high of a salt level
may damage the power supply and cause corrosion to pool metal fixtures and
accessories. The Salt Table page of this manual, shows the correct dosage of salt
needed. The salt in the pool is constantly recycled. Salt loss occurs only when pool
water is physically removed from the pool. Salt is not lost due to evaporation.
• Adding Salt
1. Switch on the unit, then press and hold both and button for 5 seconds,
the LED flashes “FP”. The unit is now in a Filter pump working mode and
switch the filter pump on to start the water circulation.
2. Keep the saltwater system turned off.
3. Determine the amount of salt to be added (see “Salt Table”).
4. Evenly spread the proper amount of salt around the inside perimeter of the
pool.
5. Avoid clogging the filter by not adding salt through the skimmer.
6. Brush the pool bottom to speed up the dissolving process. Do not allow salt to
pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to
thoroughly dissolve the salt.
7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,
press button until you hear a “beep”, code “00” flashing (see “System
Operation” section steps 2 to 4) and set the saltwater system to desired
operating time (see “Operating Time Table”).
• Removing Salt
If too much salt has been added, the unit will beep and display “code 92” (see
“Alarm Codes”). You will need to lower the salt concentration. The only way to do
so, is to partially drain the pool and refill it with fresh water. Drain and refill
approximately 20% of the pool’s water until the “Code 92” disappears.
• Pool Volume Calculation
Rectangular Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool Gallons
(pool size in feet) Cubic Meters
(pool size in meters)

133
SAVE THESE INSTRUCTIONS Page 16
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS SALT TABLE
This table shows the amount of salt needed to achieve and maintain the optimal 3000 ppm
salt level.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Salt Needed for
Startup
3.0g/L (3000ppm)
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569 cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 65 30 20 10
2822 10681 65 30 20 10
3284 12430 80 35 20 10
3736 14141 95 45 20 10
3754 14209 95 45 20 10
4273 16173 110 50 30 15
4786 18115 120 55 30 15
5455 20647 135 60 35 15
5894 22309 150 65 40 20
3282 12422 80 35 20 10
3861 14614 100 45 20 10
4440 16805 110 50 30 15
5061 19156 125 55 30 15
6423 24311 160 75 40 20
6981 26423 175 80 45 20
8638 32695 220 100 60 25
11483 43462 290 130 75 35
12481 47241 310 140 85 40
5061 19156 125 55 35 15
6981 26423 175 80 45 20
5061 19156 125 55 35 15
6981 26423 175 80 45 20
2885 10920 65 30 20 10
4393 16628 110 50 30 15
5407 20465 135 60 35 15
6420 24300 160 75 40 20
4545 17203 115 50 30 15
8403 31805 210 100 55 25
14364 54368 360 165 95 45

133
SAVE THESE INSTRUCTIONS Page 17
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS OPERATING TIME TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28 °C
(68 - 82°F)
29 - 36 °C
(84 - 97 °F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569 cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587
2822
3284
3736
3754
4273
4786
5455
5894
3282
3861
4440
5061
6423
6981
8638
11483
12481
5061
6981
5061
6981
2885
4393
5407
6420
4545
8403
14364
9792
10681
12430
14141
14209
16173
18115
20647
22309
12422
14614
16805
19156
24311
26423
32695
43462
47241
19156
26423
19156
26423
10920
16628
20465
24300
17203
31805
54368
1
1
1
1
1
2
2
2
2
1
1
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
1
2
2
2
2
2
2
1
2
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
2
2
2
2
2
3
3
2
2
2
2
3
3
4
5
6
2
3
2
3
1
2
3
3
2
4
7

133
SAVE THESE INSTRUCTIONS Page 18
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays. To
maintain maximum performance, we recommend that the cyanuric acid level be maintained at
approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs) cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569 cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 0.6 0.3
2822 10681 0.7 0.3
3284 12430 0.8 0.4
3736 14141 0.9 0.4
3754 14209 0.9 0.4
4273 16173 1.1 0.5
4786 18115 1.2 0.5
5455 20647 1.4 0.6
5894 22309 1.5 0.7
3282 12422 0.8 0.4
3861 14614 1.0 0.4
4440 16805 1.1 0.5
5061 19156 1.3 0.6
6423 24311 1.6 0.7
6981 26423 1.7 0.8
8638 32695 2.2 1.0
11483 43462 2.9 1.3
12481 47241 3.1 1.4
5061 19156 1.3 0.6
6981 26423 1.7 0.8
5061 19156 1.3 0.6
6981 26423 1.7 0.8
2885 10920 0.7 0.3
4393 16628 1.1 0.5
5407 20465 1.4 0.6
6420 24300 1.6 0.7
4545 17203 1.1 0.5
8403 31805 2.1 1.0
14364 54368 3.6 1.6

133
SAVE THESE INSTRUCTIONS Page 19
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SALT TABLE FOR COMMON NON-INTEX POOLS
OPERATING TIME TABLE FOR COMMON NON-INTEX POOLS
SALT CALCULATION FORMULA FOR ALL POOLS
Water Capacity Salt Needed for Startup
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
2000 7500 50 20 10 5
4000 15000 100 45 25 10
6000 22500 150 65 40 20
8000 30000 200 90 55 25
10000 37500 250 110 70 30
12000 45500 300 135 80 35
14000 53000 350 160 95 45
Salt Needed for Startup
(Lbs)
Salt Needed for Startup
(Kgs)
Salt Needed when
Low Salt Detected (Lbs)
Salt Needed when
Low Salt Detected (Kgs)
Water Capacity (Gals) x 0.025
Water Capacity (Liters) x 0.003 Water Capacity (Gals) x 0.0067 Water Capacity (Liters) x 0.0008
CYANURIC ACID TABLE FOR COMMON NON-INTEX POOLS
Water Capacity Operating Time (hours)
at different ambient/air temperatures
(Gals) (Liters) 10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
1
2
2
3
4
5
6
1
2
3
4
5
6
7
1
2
2
3
4
5
6
Water Capacity Cyanuric Acid Needed for Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
0.23
0.45
0.68
0.90
1.13
1.37
1.59
0.5
1.0
1.5
2.0
2.5
3.0
3.5

133
SAVE THESE INSTRUCTIONS Page 20
(133) MODEL CS8111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
OOPPEERRAATTIINNGGIINNSSTTRRUUCCTTIIOONNSS
FILTER PUMP OPERATION
1. Make sure the unit is switched off. The switch is located on the control station.
2. Connect the power cord to a GFCI protected electrical outlet.
3. Grasp a plunger valve handle. Turn the handle counter-clockwise, pull up until it
stops, and then turn it clockwise until the metal protruding notch anchor is in the
"0/1" position. Repeat for the second plunger valve. This opens the valves,
allowing water to flow into the unit.
4. With water flowing into unit, the water pressure will allow the air trapped inside
to escape from the air release valves (1 & 7). When all the air has escaped
water will flow out of the valves (1 & 7). When this occurs gently finger tighten
the valves in a clockwise direction.
5. Turn on the switch. The filter pump is now filtering the water.
6. The green "Pump" light on the control panel will light up, that indicates the filter
pump is running.
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open air
release valves, lift and lower the inlet hose until water starts to flow out of
the air release valves, close air release valves.
IMPORTANT
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI). Contact a
qualified electrician if you cannot verify that the receptacle is protected by
a GFCI.
WARNING
71