Inventus Power SBM-01 User manual

inventuspower.com
[e-mail]
+1 877.423.4242
Inventus Power, Inc.
1200 Internationale Parkway
Woodridge, IL 60517
Designed & Manufactured by
Smart Battery Monitor
Quick Start Guide
SBM-01

2
PROformance Add-On Device
Quick Start Guide
Applicable Models
Document Information
Inventus Power® is a trademark of Inventus Power.
Copyright© 2023 Inventus Power All rights reserved.
Technical Support
If you have any technical questions regarding the PROformance Add-On Device, please
contact our technical support team at:
Phone: [phone]
E-mail: [e-mail]
Release Date Revision Scope of Change
2023-03-15 V1.3 Minor edits to V1 release
Model Part Number
U1LiFePROTM Smart Battery Monitor Kit 903-09472-001
PROTRXionTM 48V60-TRX-HD Smart Battery Monitor Kit 903-09472-002
PROTRXionTM 24V80 24V90 36V80 48V60 Smart Battery Monitor Kit 903-09472-003
PROTRXionTM 12V100-TRX-HD 24V60 Smart Battery Monitor Kit 903-09472-004
PROTRXionTM 48V60 (Old Pinout) Smart Battery Monitor Kit 903-09472-005

3
Safety and Tools
Before working with any electrical products or where electricity is present, the
following guidelines are required:
• Turn o system power, disconnect battery, and place battery in ship mode
• Proper PPE (Personal Protective Equipment)
• Rubber gloves
• Safety glasses
• Insulated tools
• Removal of any jewelry
Tools Needed
• Drill and 51mm hole cutter
• Hand saw
• Insulated torque wrench
• Insulated Philips Screwdriver (optional)
• Sandpaper
Mounting Hole
Note: A hole will need to be cut if the existing panel does not include a 51.7mm diameter hole.
See next page for instructions.
1. Using a drill with a 51mm hole cutter, cut hole (Note: if the SBM-01 cannot be inserted
through the clearance hole easily, the hole can be increased using the sandpaper)
2. Locate top of hole, mark desired location to cut alignment notch
3. Using a handsaw, cut a 5.5mm x 4.5mm notch as shown in above figure
Ø51.7±0.2 mm
5.5±0.2 mm 4.5±0.2 mm

4
Mounting Hole
1. Connect battery M12 signal port to cable harness (communication cable may vary per
battery model, see SBM-01 User Manual for more information).
2. Connect Smart Battery Monitor to 8-pin connector.
3. Leave 4-pin connector disconnected if battery axillary power can provide >1A continuous
current. If the battery cannot, battery terminals must be connected to power the Smart
Battery Monitor (see SBM-01 User Manual for more information on matching the correct
cable harness with battery model).
NOTCH TO SECURE MONITOR
(5.5mm WIDE x 4.5mm)
CABLE
ALIGNMENT KEY
(5.14mm x 4.2mm)
CLEARANCE HOLE
(Ø51.7 ± 0.2MM)
1. Insert Smart Monitor threaded body through clearance hole (51.7±0.2mm) using alignment
key with notch (reference note above for creating clearance hole)
2. Secure monitor with Nut and tighten to 3 Nm torque
3. Attach 8-pin Cable to Rear of Smart Monitor (reference User Manual for specific battery
model and wire harness part number)
Cable Installation (example)
3
1
2
1.8m1.8m
Not to scale

5
Operating SBM-01
1. Display
2. MODE Button
• Activates display while in shutdown or sleep mode
• Shuts down monitor when pressed for 3 secs
• Toggle between Home Screen and Status Screen
Once the monitor is installed, powered up, and establishes
communication with the battery, the Startup Screen will
be displayed for 3 seconds, followed by the Home Screen.
To shutdown the monitor, hold the MODE button for 3
seconds.
The monitor will go to sleep after 5 minutes of battery
inactivity. To activate the display, tap the MODE button.
1
2
Startup Screen Home Screen Status Screen
• Battery State of Health
displayed for 3 seconds
• Battery charging icon
(only in charge mode)
• State of Charge (%)
• Battery Runtime Remaining
• Battery Voltage (V)
• Battery Fault Alert (only
appears when there is a fault)
• ERROR: Battery Fault Code
• BATT TEMP: Battery
Temperature (°C)
• LIFE AH USED: Cumulative
lifetime discharge capacity
(Ah)
• CURRENT: Charge/Discharge
Current (A)
• SW VER: Battery Software
Version [BQ, ATSAM, SBM-01]
Get To Know Your Smart Monitor Display Settings
Need More Help?
Contact [e-mail]
+1.877.423.4242