Connect the cables from the Quattro LNB to the input connectors marked with LNB V/L, V/H, H/L and
H/H inputs (pay attention to identification of the Quattro LNB connectors). The multiswitch is equipped
with Terrestrial input. Connect the Terrestrial antenna to this input:
V/LV/H H/L H/H
Terrestrial
input
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch
4 User Bands with combined Terrestrial input, 1 Legacy port
IDLP-UST1O1-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Unicable Out Legacy Out
Terrestrial
loop through
output
There are two output connectors: Legacy and Unicable.
The Legacy output is a standard Universal switching output that allows to connect a legacy receiver
that is not supporting the Unicable protocol.
The Unicable output allows to connect up to 4 receiver tuners – each needs to be allocated one of the
4 user bands supported by the multiswitch.
Each receiver tuner is assigned with 1 out of 4 communication channel frequencies (user band). The
frequencies are listed on the product sticker:
V/ L V / H H/L H/H
T e rrestrial
in p u t
S a te l l i t e - Input
H/ H
H/L
V/ H
V/ L
S a te l l i t e - loop-th r ough output
TM
Unicable cascadable switch
4 User Bands with combined T e rrestrial input, 1 Legacy port
IDLP-UST1O1-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Unicable Out Legacy Out
T e rrestrial
loopthr o u g h
ou t p u t
V/L V/H H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands, 1 Legacy port
IDLP-USW112-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out Legacy Out
For optimized performance, please follow the recommendations below:
use the highest frequency for a wall socket located the nearest to the multiswitch and use the1.
lowest frequency for wall socket located farest to the multiswitch.
If you install less than 4 receiver tuners, use the lowest frequencies first. We also recommend2.
to keep record of the user bands allocated to the different connections as these user bands will
then have to be set in the receiver. The satellite receivers connected to the multiswitch have to
be Unicable-compatible (usually marked with Unicable™ logo).
Note: Loopthrough outputs that are not used should be terminated with 75ohm DC-blocked
terminations.
Safety
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A lightning
strike into the antenna may cause dangerous overvoltage over the product’s metallic/conductive
parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adaptor.
If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long periods of
time. When disconnecting the product don’t pull the cable but the plug to prevent damage of the cable
(wobbly plugs and outlets result in fire risk). The product should be serviced by qualified experts only.
Thank you for purchasing Inverto’s advanced Unicable multiswitch and we are certain it will meet your
expectations. Before installing and operating the product, please read the following instructions and
recommendations. We suggest that you keep this manual for future use.
Warranty
This Unicable multiswitch is designed for the distribution of satellite and terrestrial television and radio
signals in home installations. The warranty does not apply for products used for other purposes than
those specified herein. The user/installer shall be responsible for any damage incurred as a result of
not using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface.
The product shall be in no case held only with the connected cables.
Place the product in a dry environment where it is not exposed to rain or running water.
Do not install the product close to heat sources or in places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
V/ L V/ H H/L H/H
T e rrestrial
in pu t
Sa t el l i t e - Input
H/ H
H/L
V/ H
V/ L
Sa t el l i t e - loop-thr ough output
TM
Unicable cascadable switch
4 User Bands with combined T e rrestrial input, 1 Legacy por t
IDLP-UST1O1-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Terrestrial Loop-Through loss: -3dB
Unicable Out Legacy Out
T e rrestrial
loop thr ou g h
ou tp ut
64 mm
107 mm
17.80 mm
To connect the product inputs and outputs use
high-quality coaxial cables designed for satellite reception
and F-connectors. Use a high-shielding coaxial cables with
minimum 90dB. If you use wall sockets to loopthrough the
4 user bands, make sure the wall sockets were designed
for satellite reception compatible with Unicable technology
and allows bidirectional signal propagation.
The switch may be powered by the connected STBs direct-
ly or through the supplied Power Inserter and AC adaptor.
For long cable installations, it is recommended to use the
supplied Power Inserter and the AC/DC adaptor in order
to ensure proper and stable input voltage level.
The following diagram describes the installation configurations supported by the product:
V/ L V/ H H/L H/ H
T e rrestrial
in p u t
S a te l l i t e - Input
H/ H
H/L
V/ H
V/ L
S a te l l i t e - loop-thr oughoutput
TM
Unicablecascadable switch
4User Bands withcombined T e rrestrial input, 1 Legacy port
IDLP-UST1O1-CUO1O-4PP
UserBands:
0: 1210MHz
1: 1420MHz
2: 1680MHz
3: 2040MHz
Satelliteinputs: IF 950-2150MHz
SatelliteLoop-Through loss: -3dB
TerrestrialLoop-Through loss: -3dB
UnicableOut LegacyOut
T e rrestrial
loopthr o u g h
ou t p u t
Quattro
LNB 1
Terminated
Outputs
x4 User bands
UB 0 UB 1
UB 2 UB 3
V/ L V/ H H/L H/ H
T e rrestrial
in p u t
S a te l l i t e - Input
H/ H
H/L
V/ H
V/ L
S a te l l i t e - loop-thr oughoutput
TM
Unicablecascadable switch
4User Bands withcombined T e rrestrial input, 1 Legacy port
IDLP-UST1O1-CUO1O-4PP
UserBands:
0: 1210MHz
1: 1420MHz
2: 1680MHz
3: 2040MHz
Satelliteinputs: IF 950-2150MHz
SatelliteLoop-Through loss: -3dB
TerrestrialLoop-Through loss: -3dB
UnicableOut LegacyOut
T e rrestrial
loopthr o u g h
ou t p u t
Terrestrial
TV antenna
x4 User bands
UB 0 UB 1
UB 2 UB 3
Power
inserter
Legacy satellite
receiver
Legacy satellite
receiver
AC/DC Input
2 3
