IOGear Network Adapter GUW2015V User manual

1
GUW2015VKIT
PART NO. M1062
Installation
Installation Guide
Wireless USB to VGA Kit

2
3

2
3
Table of Contents
System Requirements 4
Important Information 5
Package Contents 6
Device Overview 7
Wireless USB Host Adapter 7
Wireless VGA Adapter 8
Wireless VGA Software Installation 10
Wireless VGA Display Settings 19
Wireless USB Manager 24
Wireless USB Host Adapter Settings 26
Wireless USB Host Adapter Selection 28
Wireless USB Host Adapter Reset 29
Wireless VGA Adapter in wired mode 30
Frequently Asked Questions 31
Technical Specications 34
Limited Warranty 36
Federal Communications Commission
(FCC) Statement
37
Contact 38
Appendix 39
Compatibility with GUWH104KIT 39
Cable Association 40

4
5
System Requirements
- Microsoft Windows®XP 32-bit (Service Pack 2)
- Microsoft Windows®Vista®32/64-bit
- USB 2.0 Compliant hardware and system
- Display with VGA port (VGA cable not included)

4
5
Important Information
Before you get started, please NOTE:
Do not place Wireless USB devices under direct sunlight or near high heat emitting devices;
Do not place Wireless USB devices near water or wet surfaces to avoid electric hazards;
Do not place Wireless USB devices on any moving or unstable surfaces.

6
7
Package Contents
1 x Wireless USB Host Adapter (for PC)
1 x Wireless VGA Adapter (for Monitor/TV/Projector)
1 x USB 2.0 A to mini-B Cable (3 ft.)
1 x USB 2.0 Extension Cable (5 ft.)
1 x Velcro fabric hook-and-loop fastener
1 x Power Adapter
1 x Quick Start Guide
1 x Registration / Warranty Card
1 x Installation CD (with User Manual)

6
7
LINK PWR
Device Overview
1. LINK: Data Transfer Activity Indicator
LED blinks when data is being transferred
a.
2. PWR: Power
LED is solid when powered by the PC
a.
12
Wireless USB Host Adapter

8
9
Wireless VGA Adapter
132
4 5 6 7 8

8
9
1. VGA : VGA Activity Indicator
a. LED is solid when display cable is connected
b. LED is blinking when data is being transferred
2. PWR: Power Indicator
a. LED is solid when power is applied
3. 1 – 2 – 3: Status Indicator
Single* solid light: device is wirelessly connected to
a.
the selected Wireless USB Host Adapter
Single* slowly blinking light: device is searching forb.
a Wireless USB Host Adapter
Single* quickly blinking light: device is trying to con-c.
nect to a Wireless USB Host Adapter
Rapidly scrolling lights: device is used in wiredd.
mode.
Three Simultaneous Blinking Lights: Cable As-e.
sociation Mode
*Only one light at a time. The position of the light indicates
which Wireless USB Host Adapter the device is trying to
communicate with.
4. PWR plug
Power adapter socket
a.
5. RESET
Association history can be erased by pressing and
a.
holding this button for 10 seconds
6. HOST
This button is used to select a different Wireless
a.
USB Host Adapter
7. USB connector
In wireless mode, this connector is used for cable
a.
association
In wired mode, this connector is used for wired
b.
operation
8. WIRELESS/WIRED switch
Choose from wired or wireless mode by using
a.
this switch

10
11
Wireless VGA Software Installation
IMPORTANT NOTE:
If installing on Windows XP, Service Pack 2 (SP2) is required, verify that this has been installed before
installing the Wireless VGA kit software.
Before installing the software, please make sure that the Wireless USB Host Adapter and Wireless VGA
Adapter are not connected to the computer, and the Wireless VGA Adapter is not powered.
Step 1 – Insert installation CD into drive on
your computer.
Step 2 - Select “Software Installation” from
the menu.
Step 3 – Choose installation method.
The next screen will let you choose whether
you want to install the latest software from the
IOGEAR website or if you want to install the
software directly from the installation CD.

10
11
If selecting Option 2: Download latest software
installer from the Web, a web browser window
will launch directing you to the IOGEAR website
where you will nd the most up-to-date software.
Once you download the software, double-click on
the .exe le to begin the installation process.
If selecting Option 1: Install directly from CD,
the installation will start automatically.
Step 4 –If you previously installed the
GUWH104KIT software, then you will be prompted
to remove the software from your computer.
For more information, please see Appendix.

12
13
Step 5 – For Windows XP users, if you do not have Microsoft .NET Framework 2.0 installed, you will be
prompted to have it installed.
Click “Yes” to install .NET 2.0 Framework.1.
Check “License Agreement” and click “Install”.2.
Click “Finish” to complete installing .NET Framework 2.0.3.
Restart the computer when prompted.4.
Eject your CD and go to Step 1.5.
Step 6 - Wireless VGA kit software installation procedures.
Make sure the Wireless USB Host Adapter is NOT connected to PC, and the Wireless VGA Adapter1.
is NOT powered or connected to any device.
Follow the on-screen instructions.2. Important: reboot if prompted.

12
13
Step 7 - Driver Installation for Wireless USB Host Adapter.
Make sure the antenna is connected to the Wireless USB Host Adapter.A.
Plug the Wireless USB Host Adapter to your computer via option 1 or 2. Windows will detect theB.
device and complete the driver installation process automatically.
Option 1:
Plug the Wireless USB Host
Adapter into any available USB
2.0 port on your computer.

14
15
Option 2:
If using with a Desktop PC, plug the Wireless USB Host Adapter into
an available USB 2.0 port utilizing the provided extension cable.
Place the extension cable on a fl at surface, preferably the top of the
desk/work area in order to ensure a good line-of-sight signal with the
Wireless VGA Adapter.
LINK PWR

14
15
Step 8 - Driver Installation for Wireless VGA adapter
Make sure the antenna is connected to theA.
Wireless VGA adapter.
Connect one end of the VGA cable (not in-B.
cluded) to the Wireless VGA Adapter, and the
other end to your display’s blue VGA port.
For LCD Monitor / Flat-Panel TV•

16
17
For Projector•

16
17
Plug the power cable into the Wireless VGA adapter. Make sure the Power Indicator LED is solid.C.

18
19
Windows will automatically install the appropriate
Wireless VGA Adapter drivers.
Change your display’s setting to select VGA as
your input device. Please refer to the operating
instructions supplied with your display.
You may use the included Velcro®fabric hook-
and-loop fastener to attach the Wireless VGA
adapter to your projector or LCD display in order
to ensure a good line-of-sight signal with the
Wireless USB Host adapter.
Congratulations, your Wireless VGA Kit is
ready for use.

18
19
To change the display settings, right click on the Monitor icon in the Windows system tray.
A menu will appear and you will have the ability to change parameters such as resolution, color quality,
Wireless VGA Display Settings
mirror mode or extension mode and more.

20
21
Video Mode Conguration
By default, your installation will be set with the
best resolution for your computer and will extend
your screen to the right. You may change the
screen mode and the operation mode.
Note: If no output is seen on the monitor
connected to the Wireless VGA Adapter, it may
be in a mode which cannot be displayed by the
monitor. This can happen if the monitor does not
have its supported modes to the Wireless VGA
Adapter. Reduce the resolution of the primary
display until an image is shown.
There are two options to adjust the Resolution,
Color Quality, Screen Rotation, and Extended
or Mirror Mode. One is to click on the IOGEAR
DisplayLink Manager icon in the Windows tray
as shown above, another is to go to Control
Panel, double click on “Display”, then choose
“Settings” tab.
Mirror Mode
Mirror mode duplicates the primary display to the
monitor connected to the Wireless VGA Adapter.
The resolution, color depth and refresh rate of the
primary screen will be replicated to the monitor
connected to the Wireless VGA Adapter. If the
monitor connected to the Wireless VGA Adapter
supports a lower resolution than the primary
display, then a part of the screen is shown on the
mirrored display. As the mouse is moved around
the screen, the Wireless VGA Adapter display will
scroll to the current area.