IPC Eagle BX12 User manual

OPERATIONS MANUAL
& PARTS LIST
BX12, BX12H
Fastracts Extractor
IPC Eagle •3650 Dodd Rd, Eagan MN 55123 •800.486.2775 •www.ipceagle.com
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

BEFORE OPERATING THE MACHINE
Read the manual carefully and completely before attempting to operate the unit. This manual has important
information for the use and safe operation of the machine. Keep this manual handy at all times. This machine
will assure years of satisfactory service if operated and maintained according to recommendations in this
manual. If additional information is needed, please contact your local distributor or write to:
IPC EAGLE
3650 Dodd Rd.
Eagan, MN 55123
WARNING
•The machine was designed for use on carpet, floor and upholstery extraction applications as per instructions
and recommendations written in this manual. Any deviation from its proper use or purpose and the
consequential damage that may occur is the sole responsibility if the end user.
•Disconnect the power cord from the outlet before servicing. Do not leave machine connected to an electrical
outlet when unattended.
•Do not immerse or use this machine in standing water. Such use may cause electric shock.
•This equipment is not designed to handle or use combustible/volatile substances such as gasoline or
kerosene, in, on, or near the machine. The use of such materials will cause extreme hazardous condition.
•When using an extension cord, use only a 3-prong conductor grounding cord- 12 ga. wire or heavier.
•To avoid electric shock, do not expose the unit to rain. Store it indoors only.
•Do not use the machine for dry vacuuming.
•Use defoamer at all times to prevent damage to the vacuum motor(s).
•Do not use water in excess of 170ºF (76ºC).
•To prevent seal damage and chemical build-up to the pump system, run clean water through the solution
lines after each day’s use.
•Use only commercially available carpet cleaning solutions and defoamer intended for use with machines of
this type. Do not use dyes, bleaches, ammonia, or other additives. The use of powdered cleaning solution if
not diluted properly may result in damage to the pump. If powdered chemicals are used, premix in a
separate container before placing in the solution tank.
•Do not expose machine to freezing temperatures.
•All repairs must be done by an authorized IPC repair station.
•Do not use replacement parts other than those specified on the parts list.
For units with HEAT’N’RUN heater:
•Read and understand the HEAT’N’RUN owners manual before using the HEAT’N’RUN heater on your
FASTRACT Extractor.
•Do not run heater dry.
•Water hookups must be in place and water flowing through the heater prior to turning it on. Failure to do so
may cause internal component damage and will void warranty
•Heater must be filled with water or water based solutions at all times when in use. Turn off the switch and
unplug the heater from outlet when not in use.
•Do not use heater at more than 500 PSI
•Do not immerse heater in water
•To avoid explosion and / or fire, do not use solvents or any flammable liquid in heater.
FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THE WARRANTY
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

GROUNDING INSTRUCTIONS
The120V A/C and the 220V A/C models have been outfitted with the appropriate grounded connectors. Make
sure the machine is connected to a grounded outlet having the same configuration as the grounded plug. No
adapter should be used with this machine. Any modification to the connectors will void the warranty.
PREPARING THE MACHINE (ALL FASTRACT EQUIPMENT)
IMPORTANT:For all FASTRACT equipment, use only the correct IPC high pressure, high heat wands &
upholstery tools. They are designed to deliver and maintain the correct gallons per minute (GPM), pressure
(PSI) and heat when attached to the FASTRACT pump system. Use of other manufacturer wands can cause
over-wetting of carpet, damage to the pump system (including hose & fittings), lack of pressure and heat.
1) Pour clean solution into the solution tank
2) Slide vacuum hose onto the black hose adapter (located at the back of the machine) and the wand or
upholstery tool.
3) Connect the male end of the solution hose to the wand and the female end to the machine by sliding
knurled collar on the female quick disconnect fitting back. Push the male fitting in and release the
knurled collar until it snaps back.
4) Make sure the drain valve is closed by pushing the T-handle all the way in.
5) Previously shampooed carpets usually have a heavy build-up of old shampoo residue which can cause
the vacuum system to ingest foam and result in damage to the vacuum motor. Remember to add
recommended amount of defoamer to the recovery tank every time you fill the solution tank.
Additional Instructions for FASTRACT with a HEATER:
1) Be sure to fill the solution tank with water before plugging in the machine.
2) Water hookups must be in place and water flowing through the heater prior to turning it on. Failure to do
so may cause internal component damage and will void the warranty.
Spray water through the tool / wand before turning on the heater to assure that there is water
flow.
3) Heater must be filled with water or water based solutions at all times when in use.
4) Plug heater power cord and machine power cord into separate outlets on separate circuits.
5) Turn off the switch and unplug the heater from outlet when not in use.
6) Do not use heater at more than 500 PSI.
7) Turn on heater switch when you are ready to clean.
8) CAUTION: When the green light on the heater is on, the heater is heating. When the green light is off,
the water in the heater tank is up to temperature and the thermostat switch in the heater has turned the
heater off. It will automatically turn on again when the water temperature in the heater has cooled.
DELIVER MAXIMUM HEAT by performing the following SYSTEM WARM-UP PROCEDURES at the
start of each day:
1) Attach the solution hose to the quick disconnect on the machine.
2) Attach the warm-up quick disconnect with spray tip attached to the other end if the solution hose.
3) Place warm-up quick disconnect in the solution tank.
4) Fill solution tank with cleaning solution.
5) Turn on pump.
6) When water is flowing out of the warm-up quick disconnect, turn on the heater.
7) Let the pump and heater run for 4 to 5 minutes.
8) Remove warm-up quick disconnect. Attach the wand or upholstery tool and begin cleaning.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

OPERATING INSTRUCTIONS- CARPET TOOL
1) Turn on the vacuum and solution switches. Slowly pull the tool towards you with the solution valve
trigger engaged. Then make a pass forward and backward with the vacuum only (no spray) over the
cleaned area to remove as much dirt and solution as possible. Do not overwet carpet! Make overlapping
passes to prevent streaking.
2) If the carpet is heavily soiled, squeeze solution valve on the forward pass as well as backwards, allowing
cleaning solution a few seconds longer to work prior to vacuuming. Another method is to raise the wand
8” above the carpet and pre-spray lightly prior to cleaning passes. On extremely soiled carpets, we
recommend using a pre-spray solution.
3) When you run out of solution, turn off the pump. Attach the drain elbow on the drain valve. Place a pail
under the downspout and pull up the drain valve T-handle. Dirty solution will pour out until the tank is
empty. Close the drain valve. Use a clean bucket when you refill the solution tank.
4) When the job is completed, turn the switch off and disconnect the vacuum and solution hoses from the
carpet and the machine. Drain the recovery tank through the drain valve as before.
CLEANING UPHOLSTERY
Cleaning upholstery with success requires a good knowledge of the type of fabric you will work on. Look for
the cleaning instructions label sewn on the underside of the furniture for the recommended method of cleaning.
If it calls for dry cleaning, do not attempt to clean by wet extraction otherwise damage to the fabric could occur.
Extraction works perfectly on most synthetic fabrics including synthetic velvets.
Before proceeding, test the fabric for colourfastness. Apply a small amount of cleaning solution on the fabric in
an inconspicuous spot. Wait 2 to 3 minutes and rub the area with a white terry cloth towel. If no color comes off
the towel, the fabric should be safe to clean. If a little color comes off, there is some risk of colors running when
you clean. It may be possible to stabilize colors by cleaning with an acidic rinse.
1) Prepare the machine in the same manner as for carpet cleaning (see Preparing the Machine) except
attach the upholstery tool to the vacuum hose. Connect the solution hose. Pour hot water into the
solution tank. Add recommended amount of cleaning concentrate into the solution tank. Turn on the
vacuum and pump switches.
2) Adjust the pump “operating pressure” to 50 PSI or below for upholstery cleaning (See Preparing the
Machine).
3) Clean with the upholstery tool using as little solution as possible. Make overlapping passes to prevent
streaking. Go over the area you just cleaned without depressing the lever (vacuum only) and gauge the
amount of moisture extracted through the view window for dryness. On heavily soiled areas like arm
rests, pre-treat with a recommended pre-spray solution or hold the upholstery tool a few inches above
the fabric and press lever to spray on the solution before making a pass.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

DAILY MAINTENANCE
1) Always keep the machine clean inside and out.
2) Pour 2 gallons of clean hot water in the solution tank. Turn on and flush the entire system through the wand
nozzles for about a minute to prevent build-up.
3) Remove dirt and lint build-up inside the filter screen in the recover tank. Lint should be cleaned off so that
air flow is not impeded.
4) Check the solution tank strainer in the solution tank. If lint has accumulated in the screen, remove and rinse
it in clear running water.
PERIODIC MAINTENANCE
All IPC machines are engineered and built to require a minimum of maintenance. But like any machine, it does
require some care to keep it in optimum working condition. Careful attention to these maintenance instructions
will give you maximum operating performance and will increase the life expectancy of your machine.
•Solution Lines and Fittings: Flush the machine at least once a month with a solution of 3 parts water with 1
part white vinegar in order to neutralize the alkaline residue left by the cleaning solution.
•Quick Connect Coupler: Spray with WD-40 or equivalent lubricant to prevent coupler from sticking.
•Drain Valve: Apply light oil on gate seals. If machine has to be stored, leave the gate valve open.
•Solution Pump: The same above procedure used on the solution line and fittings applies to the pump.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

1
2
4
3
5
6
9
10
11 12 13 14 15
23
22
21
20
28
29
30
31
32
33
34
35
36 38
37
32
39
40
41
42
43
4445
47
48
7
8
19
27
49
16
25
BX12
Upper
IPC
2000SX-HR Upper
2-6-08
1817
24
26
5-A
5-D 5-C
5-B
50
A
B
C
D
46
ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 F11787 Solution Tank 1
2 F11788 Recovery Tank 1
3 F11791 Lid, Solution Tank 1
4 E11124 Gasket, Recovery Tank 1
5 12904A Stand Pipe Assembly 1
K11965 Elbow, 180 Deg. Float Ball 1
K00672 Pvc Pipe, 1.5 X 12 in, Sch 40 Wht 1
10989-2A Float Ball Screen 1
K00741 Adapter 1
6 F11785 Lid, Recovery Tank 1
7 C12039 Washer, 1-4 X 1, SS 2
8 C02322 1-4 X 20 Bolt 2
9 B11769 Extension Cord, 12-3 SJTW 1
10 C11177 Velcro Strap 1
11 H02548-2 Label, Important, Cord 1
12 B00185-30 Wires, 73 in 1
13 B00185-40 Wires, 73 in 1
14 B010314 Wire Harness 1
15 F11786 Handle 1
16 B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated 2
17 B00185-40 Wire,14 GA Black, UL1015, 5 in 1
18 C00295-1 #10 X .75in Pan, Black SMS, Phillips 2
19 C00293 #8 X .5in Pan, Black SMS, Phillips 2
20 D11168 Cover, Switchplate, Galaxy 1
21 B02211-1 Switch, Rocker, Green Light 3
22 D010284 Switchplate 1
23 E010453 Gasket, Switch Bracket 1
24 B00177-1 Terminal Lug, Female, QD, .25 X .032 4
25 B00185-30 Wire,14 GA White, UL1015, 5 in 1
26 C02315 Lockwasher, #10 Int. Str, SS 2
27 C00264 Nut, 10-32 1
28 C11141 Screw, Allen Head, 10-24 X 1.25 in 8
29 K00665-1 Hose Adapter, 1.5in, Black 1
30 E11128 Gasket, Drain Valve 2
31 C00313 Hex Bolt, .25 X 20 X .75 6
32 C00233 Washer, Flat, .25 in 8
33 C02312 Lockwasher, .25 in., Internal Star 2
34 D010283 Plate, Heater Mounting 1
35 F11804 Heater Mount 1
36 C00261 Nut, .25-20, Hex 2
37 K00711 Drain Valve, Black 1
38 K00710 Elbow, Drain Valve, Black 1
39 C00254 Lock Washer, 1-4in Split 2
40 C02294 Screw, 1-4 20 X 1.25 2
41 K11185 Elbow, 90, 1.5 in, MT-MS, PVC 1
42 K00672-1 Pvc Pipe, 1.5 X 2.25 in, Sch 40 Wht 1
43 E11129 Gasket, Base 1
44 A00060 3-8 Barb X 1-4MP, Brass 1
45 A00052 .25 X .375 M-F 90 deg Brass 1
46 C11244 Washer, .56 X 1.5 X .05 1
47 A00124 Hex Nut, .25 NPT Brass 1
48 D00373 Inlet Filter, .25 NPT 1
49 C11143 Screw, 1-4 20 X 1.5 in, SS Pan Head, Phillips 2
50 S11179 Non-Skid Tape, 1 in. Roll 1
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

BX12 (UPPER)
ITEM # PART
#
DESCRIPTION QTY
1F11275 SOLUTION TANK 1
2F11138 RECOVERY TANK 1
3F11137 LID, SOLUTION TANK 1
4E11124 GASKET, RECOVERY TANK 1
512904A STAND PIPE ASSEMBLY 1
A
K11965 ELBOW, 180º FLOAT BALL 1
BK00672 PVC PIPE, 1.5 X 12 IN, SCH 40 WHITE 1
C10989-2A FLOAT BALL SCREEN 1
D
K00741 ADAPTER 1
6F11135 LID RECOVERY TANK 1
7C12039 WASHER, 1-4 X 1, SS 2
8C02322 1-4 X 20 BOLT 2
9B11769 EXTENSION CORD, 12-3 SJTW 1
10 C11177 VELCRO STRAP 1
11 H02548-2 LABEL, IMPORTANT, CORD 1
12 B00185-30 WIRES, 73 IN 1
13 B00185-40 WIRES, 73 IN 1
14 B010314 WIRE HARNESS 1
15 F11136 HANDLE 1
16 B00177 TERMINAL LUG, FEMALE, QD, .25 X .032, 16-14 AWG, CULLY INSULATED 2
17 B00185-40 WIRE, 14 GA, BLACK, UL1015, 5 IN 1
18 C00295-1 #10 X .75 IN PAN, BLACK, SMS, PHILIP 2
19 C00293 #8 X .5 IN PAN, BLACK, SMS, PHILIPS 2
20 D11168 COVER, SWITCHPLATE, GALAXY 1
21 B02211-1 SWITCH, ROCKER, GREEN LIGHT 3
22 D010284 SWITCHPLATE 1
23 E010453 GASKET, SWITCH BRACKET 1
24 B00177-1 TERMINAL LUG, FEMALE, QD, .25 X .032 4
25 B00185-30 WIRE, 14 GA, WHITE, UL1015, 5 IN 1
26 C02315 LOCKWASHER, #10 INT, STR, SS 2
27 C00264 NUT, 10-32 1
28 C11141 SCREW, ALLEN HEAD, 10-24 X 1.25 IN 8
29 K00665-1 HOSE ADAPTOR, 1.5 IN, BLACK 1
30 E11128 GASKET, DRAIN VALVE 2
31 C00313 HEX BOLT, .25 X 20 X .75 6
32 C00233 WASHER, FLAT, .25 IN 8
33 C02312 LOCKWASHER, .25 IN, INTERNAL STAR 2
34 D010283 PLATE, HEATER MOUNTING 1
35 F11804 HEATER MOUNT 1
36 C00261 NUT, .25-20, HEX 2
37 K00711 DRAIN VALVE, BLACK 1
38 K00710 ELBOW, DRAIN VALVE, BLACK 1
39 C00254 LOCKWASHER, 1-4 IN SPLIT 2
40 C02294 SCREW, 1-4 20 X 1.25 2
41 K11185 ELBOW, 90, 1.5 IN ST-MS, PVC 1
42 K00672-1 PVC PIPE, 1.5 X 2.25 IN, SCH 40 WHITE 1
43 E11129 GASKET, BASE 1
44 A00060 3-8 BARB X 1-4MP, BRASS 1
45 A00052 .25 X .375 M-F 90º BRASS 1
46 C11244 WASHER, .56 X 1.5 X .05 1
47 A00124 HEX NUT, .25 NPT, BRASS 1
48 D00373 INLET FILTER, .25 NPT 1
49 C11143 SCREW, 1-4 20 X 1.5 IN, SS, PAN HEAD, PHILIPS 2
50 S11179 NON-SKID TAPE, 1 IN ROLL 1
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

2 3 4 6 7 8 9
11
12
13
15
16
272625242220 21
22 28
34
3738
55
39
40
454647
46
4849
50
7
51
52
54
56 57 58 59
62
54
6
17
7
63
64
65
66
32
33
42
41
7
15
31
60
61
23
53
BX12 Base
IPC
000SX-HR Base
12-1-07
36
1
14
19
18
29
43
44
55
6
35
30
5
10
ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 C00297 Screw,#8 X .25 in, Pan Head 1
2 J11863 Hose, 3 in 1
3 J00639 Screw Clamp, 1.63 - 2.43in. 3
4 J00618 Vacuum Hose, 2in Grey, Wire, 22 in lg 1
5 F11178-BLK Intercooler, Galaxy, Black 1
6 C00273 Locknut, 1-4 X 20, Nylon, SS 16
7 C00233 Washer, Flat, .25 in 26
8 E00449 Grommet 6
9 C00284 Screw, 10-32 X .375 Ground 2
10 B11150 Ground Wire, Galaxy 2
11 G00537 Vacuum Motor, 82 in, 115 V 2
12 J00657 Hose Clamp, 2 inSLDPRT 1
13 J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg 1
14 C00254 Lock Washer, 1-4in Split 1
15 C00261 Nut, .25-20, Hex 10
16 D11134 Vac Plate 1
17 C11189 Screw, 1-4 X 20 X 4.5 in, Hex 5
18 C11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips 1
19 C02312 Lockwasher, .25 in., Internal Star 1
20 G11314 Pressure Regulator, Brass 1
21 A00060 3-8 Barb X 1-4MP, Brass 1
22 A00052 .25 X .375 M-F 90 deg Brass 3
23 A00161 Tee, .25 FP, Brass 1
24 A00111 Nipple, .25 in 2
25 A00121 Fitting, .25 MP X .25 FP, Brass 1
26 C11244 Washer, .5 ID X 1,5 OD 2
27 A00104 QD, 1-4 M X 1-4 FP, Brass 1
28 A00097A Cap, Inline Filter 1
29 A00094E Checkvalve, No Strainer 1
30 A00094C Check Valve Body 1
31 C02322 Hex Bolt,1-4 X 20 X 1.75 in 4
32 D010379 Heater Mounting Plate 1
33 C11440 Spacer, Heater Mounting Plate 4
34 A00061 3-8 Barb X 1-4FP, Brass 1
35 H02564-2 Label, Caution, Motor Housing 1
36 C11165, Screw, #8 X 1 in, Pan, Black 4
37 F11790 Heater, Tunnel Cover, Blue Granite 1
38 B11779 Stub, 12-3 SJTW Yellow 1
39 C00293 #8 X .5in Pan, Black SMS, Phillips 2
40 B00192 Mount, Nylon Tie 1
41 B11606 Strain Relief, Pigtail 1
42 K10510 Plug, 1.25 in, Black 1
43 H03545 Cover, Serial # Label 1
44 H00565-5 Label, Serial Number 1
45 C02305 Cap Nut, .5in Push-on 2
46 C00240 Washer, Shoulder, Nylon 4
47 G11767 Wheel, 10 in 2
48 D11170 Axle 1
49 F11789 Base 1
50 C00314-1 Hex Bolt, 1-4 X 20 X 1in 8
51 G03518 Caster, 4 in 2
52 J00613B Solution Hose, .375 in, Black 1
53 J11508Screw Clamp #6, 7-16 to 7-8in 8
54 A00054 Elbow, 90, .375MP X .375B, Nylon 2
55 B00191 Nylon Tie, 11in Black 4
56 B00190 Nylon Tie, 4in 13
57 G00513-100 Pump, 100 PSI, 115 V 1
58 D11194 Pump Plate 1
59 J00613B Solution Hose, .375 X 26 in, Black 1
60 J11154 Solution Hose, .375 X 10 in, Wire Reinforced 1
61 A11243 Tee, .375B X .375B X .375B, Nylon 1
62 J11154 Solution Hose, .375 X 6 in, Wire Reinforced 1
63 J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg 1
64 E11169 Gasket, Vac Motor, Galaxy 2
65 B00179-2 Closed End Cntr, 16-3 1
66 B00179-1 Closed End Cntr, 16-3 3
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

BX12 (BASE)
ITEM # PART
#
DESCRIPTION QT
Y
1C00297 SCREW, #8 X .25 IN, PAN HEAD 1
2J11863 HOSE, 3 IN 1
3J00639 SCREW CLAMP, 1.63-2.43 IN 3
4J00618 VACUUM HOSE, 2 IN GRAY, WIRE, 22 IN LG 1
5F11178-BLK INTERCOOLER, BLACK 1
6C00273 LOCKNUT, 1-4 X 20, NYLON, SS 16
7C00233 WASHER, FLAT, .25 IN 26
8E00449 GROMMET 6
9C00284 SCREW, 10-32 X .375 GROUND 2
10 B11150 GROUND WIRE 2
11 G00537 VACUUM MOTOR, 82 IN, 115V 2
12 J00657 HOSE CLAMP, 2IN SLDPRT 1
13 J00618 VACUUM HOSE, 2 IN, GRAY, WIRE, 4 IN LG 1
14 C00254 LOCK WASHER, 1-4 IN SPLIT 1
15 C00261 NUT, 25-20 HEX 10
16 D11134 VAC PLATE 1
17 C11189 SCREW, 1-4 X 20 X 4.5 IN HEX 5
18 C11516 SCREW, 1-4 X 20 X 4.5 IN, FLAT HEAD, PHILIPS 1
19 C02312 LOCKWASHER, .25 IN, INTERNAL STAR 1
20 G11314 PRESSURE REGULATOR, BRASS 1
21 A00060 3-8 BARB X 1-4MP, BRASS 1
22 A00052 .25 X .375 M-F 90º BRASS 3
23 A00616 TEE, .25 FP, BRASS 1
24 A00111 NIPPLE, .25 IN 2
25 A00121 FITTING, .25 MP X .25 FP, BRASS 1
26 C11244 WASHER, .5 ID X 1.5 OD 2
27 A00104 QD, 1-4 M X 1-4 FP, BRASS 1
28 A00097A CAP, INLINE FILTER 1
29 A00094E CHECKVALVE, NO STRAINER 1
30 A00094C CHECK VALVE BODY 1
31 C02322 HEX BOLT, 1-4 X 20 X 1.75 IN 4
32 D010379 HEATER MOUNTING PLATE 1
33 C11440 SPACER, HEATER MOUNTING PLATE 4
34 A00061 3-8 BARB X 1-4 FP, BRASS 1
35 H02564-2 LABEL, CAUTION, MOTOR HOUSING 1
36 C11165 SCREW, #8 X 1 IN PAN, BLACK 4
37 F11790 HEATER, TUNNEL COVER, BLUE GRANITE 1
38 B11779 STUB, 12-3 SJTW YELLOW 1
39 C00293 #8 X .5 IN PAN, BLACK SMS, PHILIPS 2
40 B00192 MOUNT, NYLON TIE 1
41 B11606 STRAIN RELIEF, PIGTAIL 1
42 K10510 PLUG, 1.25 IN, BLACK 1
43 H03545 COVER, SERIAL # LABEL 1
44 H00565-5 LABEL, SERIAL NUMBER 1
45 C02305 CAP NUT, 5 IN PUSH ON 2
46 C00240 WASHER, SHOULDER, NYLON 4
47 G11767 WHEEL, 10 IN 2
48 D11170 AXLE 1
49 F11139 BASE 1
50 C00314-1 HEX BOLT, 1-4 X 20 X 1 IN 8
51 G03518 CASTER, 4 IN 2
52 J00613B SOLUTION HOSE, .375 IN, BLACK 1
53 J11508 SCREW CLAMP #6, 7-16 TO 7-8 IN 8
54 A00054 ELBOW, .90, .375 MP X .375B, NYLON 2
55 B00191 NYLON TIE, 11 IN, BLACK 4
56 B00190 NYLON TIE, 4 IN 13
57 G11234 PUMP, 100PSI, 115 V 1
58 D11194 PUMP PLATE 1
59 J00613B SOLUTION HOSE, .375 X 26 IN, BLACK 1
60 J11154 SOLUTION HOSE, .375 X 10 IN, WIRE REINFORCED 1
61 A11243 TEE, .375B X .375B X .375B, NYLON 1
62 J11154 SOLUTION HOSE, .375 X 10 IN, WIRE REINFORCED 1
63 J00618 VACUUM HOSE, 2 IN. GRAY, WIRE, 7 IN LG 2
64 E11169 GASKET, VAC MOTOR 2
65 B00179-2 CLOSED END CNTR, 16-3 1
66 B00179-1 CLOSED END CNTR, 16-3 3
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

https://harrissupplyind.com-ToOrderPartsCall608-268-8080