ipf electronic IN32E332 User manual

MANUAL•Subjecttoalteration!Version:Jan.2023
ipfelectronicgmbh  │ RosmarterAllee14•58762Altena•Germany │ Tel+4923519365‐0•info@ipf‐electronic.com•www.ipf-electronic.com  1
IN32E332
Inductiveproximityswitch
IV991196
Amplifier
VKC0E333
Cablesocket

Installationofthesensor
ThesensorIN32E332 isaninductiveproximityswitchfornon‐flushmounting.Duetoitsconstruction,the
deviceonlydetectsmetallicobjects.
Toachievethenominalswitchingdistanceof15mm(seetechnicaldata),musthavethemetalpart
followingproperties:Material:ST37
Dimensions:32mmx32mmx1mm
Forothermaterials,thecorrectionfactorsarelistedinthetechnicaldata.
Theswitchingdistancemaydeviatefromthenominalvalueby±20%duetocomponenttolerances.
Installthedeviceinaway,thattheplasticcapisnotsurroundedbymetal.Thelateraldistancetometallic
objectsmustbeatleast32mm.
Toavoiddamagingthethreadedsleeveduringassembly,thetighteningtorquemustnotexceed150Nm.
Thedevicemaybeusedinsurroundingswithtemperaturesupto230°C.


Installationoftheamplifier
TheamplifierIV991196istobeusedfortheoperationofthesensorIN32E332inconnectionwiththe
cablesocketVKC0E333.
ThedeviceissuitableformountingonaDINrail.Mountingmusttakeplaceoutsidethedust‐ex‐area,e.g.
inaprotectedswitchcabinet.
ThepnpswitchingoutputcanbefurtherprocessedwithaPLC.Theswitchingoutputhasaswitch‐ondelay
of100ms.

Elektricalconnection
Connectionofthesensortotheamplifierviathe
VKC0E333cablesocket:


Connectionoftheoperatingvoltageandtheswitching
outputtotheamplifier.



IMPORTANT:
Switchofftheoperatingvoltagebeforeconnectingordisconnectingtheamplifier!
Thecablesocketmayalsoonlybepluggedinorunpluggedfromthesensorwhenitisde‐energized.An
appropriatewaitingtime(>10s)mustbeobservedbeforepullingoff.
Whenplugginginthecablesocket,makesurethat,thatitsnapssecurelyintotheconnectorofthesensor.

Clamp 4: brown (sensor power supply +3V)
Clamp 5: black (screen)
Clamp 6: blue (sensor power supply GND)
Clamp 9: + UB
Clamp 8: switching output pnp, no, 400mA
Clamp 7: 0V (GND)

MANUAL•Subjecttoalteration!Version:Jan.2023
ipfelectronicgmbh  │ RosmarterAllee14•58762Altena•Germany │ Tel+4923519365‐0•info@ipf‐electronic.com•www.ipf-electronic.com
  2

TechnicaldataIV991196IN32E332
OperatingvoltageUB7to35VDC3VDC,through
amplifierIV991196
NominalSwitching
distance(sn)
13mm
Hysteresis3%bis20%fromsn
NominalSwitching
distance(sr)
sn20%
Ampacity400mA
Ambienttemperature ‐25…+70°C0…+230°C
Protectionclass
(EN60529)
HousingIP40,
ClampIP20
IP67withattachedcable
socket
HousingmaterialPlasticSleeve:VA
Cap:Vectra
Design22.5x75x110ThreadeddeviceM32x1.5Total
length83.5mm
MountingOnDINrail 
ConnectionClampLemosaconnector
Matchingcablesocket  VKC0E333
(30mlinelength)
Adjustmentfactors VAapprox.0.7
Ms,Alapprox.0.4
Cuapprox.0.3


Dimensionaldrawing:

IV991196IN32E332VKC0E333














SAFETYINSTRUCTIONS:
Beforecommissioning,pleasemakesurethatallsafetyinstructionslistedintheproductdocumentation,ifapplicable,havebeen
observed!
Incaseofdirectimpactonpersonalsafety,theuseoftheseproductsisprohibited.