IPGARD SA-DPN-1S-P User manual

DESIGNED
AND MADE
IN THE USA
TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
VIDEO
Format DisplayPort
Host Interface (1) DisplayPort 20-pin F
User Console
Interface (1) DisplayPort 20-pin F
Max Resolution 3840 x 2160 @ 30Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type
USB 1.1 and 1.0 Keyboard and
Mouse only.
USB 2.0 for CAC connection.
USB Type B Inputs (1) Keyboard-Mouse; (1) CAC
User Console
Output Interface
(2) USB Type-A for keyboard
and mouse connection only.
(1) USB Type-A for CAC
connection.
AUDIO
Input (1) Connector Stereo 3.5mm
Female
Output (1) Connector Stereo 3.5mm
Female
POWER
Power Requirements 12V DC, 2A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CERTIFICATIONS
Security Accreditation
Common Criteria Validated To
NIAP, Protection Prole PSS
Ver. 4.0
OTHER
Emulation USB 1.1 and USB 2.0
Compatible
Control Front Panel Buttons
PART NO. QTY DESCRIPTION
SA-DPN-1S-P 11-port, Secure DisplayPort
KVM Isolator
PS12VDC2A 112V DC, 2A power adapter with
center-pin positive polarity.
1Quick Start Guide
CONSOLE AUDIO
K/M
CAC
DP OUT
AUDIO
DP IN PW SL
INPUT
12VDC2.0A K/M CAC
NOTICE
The information contained in this document is
subject to change without notice. iPGARD makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
iPGARD will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
iPGARD, Inc.
20180122
SA-DPN-1S-P
Secure KVM Isolator
Advanced 1-Port Secure
Single-Head DisplayPort
KVM Isolator
Quick Start Guide
A full Manual can be downloaded from
www.ipgard.com/documentation/
Toll Free: [phone]
Phone: [phone]
Fax: [phone]
3291 N. Jones Blvd.,
Las Vegas, NV 89108
iPGARD.COM

DESIGNED
AND MADE
IN THE USA
SA-DPN-1S-P
DP IN
AUDIO OUT
DP OUT
USB IN
USB OUT
CAC IN
CAC OUT
AUDIO IN
SA-DPN-1S-P
CONSOLE AUDIO
K/M
CAC
DP OUT
EDID LEARN HARDWARE INSTALLATION
A full Manual can be downloaded from
www.ipgard.com/documentation/
The KVM is designed to learn a connected
monitor’s EDID upon power up. In the event
of connecting a new monitor to the KVM, a
power recycle is required.
The KVM will indicate the unit’s EDID learn
process is active by ashing the front
panel’s LED. The LED will ash green for
approximately 10 seconds upon beginning
the EDID learn. Once the LED stop ashing,
the power will cycle and the EDID learn will
be complete.
A monitor must be connected to the video
output port located in the console space at
the back of the KVM during the EDID learn
process.
If the read EDID from the connected monitor
is identical to the current stored EDID in the
KVM then the EDID learn function will be
skipped.
1. Ensure that power is turned off or disconnected from the unit and the computer.
2. Use a DisplayPort cable to connect the DisplayPort output port from the computer to the
corresponding DP IN port of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on the computer to the respective
USB ports of the unit.
4. Optionally, for CAC models, connect a CAC (Common Access Card, Smart Card Reader) to the
CAC port in the user console interface.
5. Optionally, connect a stereo audio cable (3.5 mm to 3.5 mm) to connect the audio output of
the computer(s) to the audio in ports of the unit.
6. Connect a monitor to the DP OUT console port of the unit using a DisplayPort cable.
7. Connect a USB keyboard and mouse in the two USB console ports.
8. Optionally, connect stereo speakers to the audio out port of the unit
9. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and
then turn on the computer.
Note: You can connect 1 computer to the 1 port KVM.
A full Manual can be downloaded from
www.ipgard.com/documentation/