Fisher & Paykel IZONA CoolDrawer RB36S User manual

WARNING!
Electrical shock hazard
Disconnect product from main power supply before installing appliance.
Failure to do so may result in electrical shock or death
Important safety precautions!
Installation of this CoolDrawer requires competent mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the CoolDrawer installation, the Installer must perform the Final Check List.
Remove all packaging materials supplied with the CoolDrawer.
The CoolDrawer is manufactured for indoor use only.
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
1
The CoolDrawer MUST be installed to allow for future removal from the enclosure if service is required.
Do not seal this CoolDrawer into the cabinetry with silicone or glue. Doing so will make future servicing
dicult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in
product, nor for repairing any damage that may be incurred by doing this.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the
power supply cord.
Failure to install the CoolDrawer correctly will invalidate any warranty or liability claims.
If the power supply cord is damaged, it must be replaced. Parts are available from your Authorised Fisher
& Paykel dealer.
Cabinetry must be suciently robust to support a combined product and food load of 100 kg (220 lb).
Bearers may be required to support the internal shelf.
Before you install the CoolDrawer, please make sure that
The switched power outlet must be outside the refrigerator drawer cavity so that it is accessible after
installation.
The switched power outlet must be located outside the cavity, within 55” (1400 mm) from the CoolDrawer
cavity if situated on the left-hand side of the cavity and within 33” (840 mm) if situated on the right-hand
side of the cavity.
The services hole in the refrigerator cavity needs to be large enough for the power supply plug to t
through.
IZONA CoolDrawer
Installation instructions
FRAMED CABINETRY
WARNING!
Tipping hazard
Do not operate this apppliance until it has been securely anchored inside the
cabinetry. The cabinet must be securely anchored to the oor.
Failure to use caution could result in injury or cuts.
RB36S & RB90S models

2PRODUCT DIMENSIONS
1 ”
(50 mm)
Product dimensions (inches (mm))
CoolDrawer
RB36S RB90S
Aoverall height of product (inc. installation brackets)
Boverall width of product
Coverall depth of product (excl. drawer panel; inc. power cord)
Ddepth of drawer (open) (excl. handle)20 ½” (520)
Installation diagrams for illustration purposes only
A
Cabinetry dimensions (inches (mm))
CoolDrawer
RB36S RB90S
Aoverall width of cabinetry frame 36” (914)
Bminimum inside width of cabinetry frame 34” (864)
C1height below top of internal shelf*
(to allow for outlet duct height)
max. 4 ¾” (120)
C2height from frame inner face to top of internal shelf
Dminimum height of toe kick 3” (75)
Eminimum depth** of toe kick
Fminimum distance from front of cabinetry to rear wall
**All depth measurements are taken from the front face of the cabinetry frame (not drawer panel)
Minimum clearances (inches (mm))
” (2 mm)
½” (13 mm)
D
Installation diagrams for illustration purposes only
B
C
D
F
E
E
F
A
B
An alternative of wooden blocks
can be used instead of the internal
shelf to position the product at the
correct height.
3CABINETRY DIMENSIONS

PARTS SUPPLIED
4
5CAVITY PREPARATION
max.
¾”(20 mm)
max. 33”
(840 mm)
min. ø ( 50 mm)
Benchtop
Panel
min. 21”
(
535 mm)
Important!
Disconnect power to surrounding appliances before preparing cavity.
Recommended to allow the vertical removal of the refrigerator bins.
min. 5” ( 130 mm)
Installation
trims (2)
Installation brackets
(left-hand and right-
hand side) (2)
Outlet duct (1)Trim brackets (4)Drawer Panel
attachment
hooks (3)
Power
cord (1)
Phillips 16 mm
( wood
screw (6)
Pan Head
16 mm (
screw (12)
Pan Head
16 mm (
screw (2)
Phillips
16 mm
( wood
screws (6)
Note: Services can be located
either side of CoolDrawer.
min. 21” ( 535 mm)
min.
5” ( 130 mm)
Shows cutout if cabinetry
depth at
( 550 mm)

A
A
6PANEL PREPARATION
Integrated Panel material
-
(16 - 20 mm) panel thickness (
¾”
(18 mm) recommended).
Maximum weight of 7 kg (15.5 lb).
Adequately sealed to withstand moisture (122
O
F/50
O
C @ 80% RH)
Height of Drawer Panel
The following information is required to correctly dene your drawer panel height:
Dimension Data Source
AReveal dimension Your kitchen designer
BHeight between top of Internal shelf and Your kitchen designer
underside of benchtop
CBottom face of Drawer panel to top of internal shelf Min. 6” (152 mm)
Max. 7
¼ ” (184 mm)
DDrawer panel height Calculated from A, B & C
To calculate D complete the following equation:
D = B - A - C
i.e. For the F&P prenished panel with a
¼ “ (6 mm) reveal:
18
¾ ” (476 mm) =26 ¼ ” (666 mm) - ¼ ”(6 mm) - 7 ¼ ” (184 mm)
Height of the False Panel
Determine the height of the false panel according to your individual kitchen cabinetry
requirements maintaining a ” (4 mm) gap between panels.
F&P prenish panel width is 35
¼ ” (896 mm)
Installation diagrams for illustration purposes only
Drawer Panel
-
(16 - 20 mm)
height of False
Panel
A
A
False Panel
width of Panels
D
height of
Drawer Panel
(4 mm)
Section A-A
Benchtop
Drawer panelFalse panel
A
D
C
B

2 2
1
3
3 3
30 ” (764 mm)
1 ” (50 mm)*
4 ” (102 mm)
max. R ” (16 mm)
11” (280 mm)
8 ½” (215 mm)
8 ½” (215 mm)
max. 33 ” (862 mm)
min. 33 ” (860 mm)
1
”
(25 mm)
3” (76.5 mm)*
1 ”
(40 mm)
2
34
1
1
2
CREATE CUTOUTS IN FRAME
7
9ATTACH OUTLET VENT DUCT
If the cabinetry does not already have cutouts, ensure the modications below are made.
Important!
Ensure the power cord is clipped in place.
Important!
Ensure a minimum of 3 screws
per side are used. The rear screws
must always be used. Horizontal
xing is also optional.
LOCATE & SECURE INSTALL BRACKETS
8
*Cutout dimensions referenced from inside face of cabinetry frame.
10 ATTACH POWER CORD & TRIM BRACKETS
Important!
Cut outlet duct to be ush
with top of internal shelf.
Important!
Note correct orientation of bracket.

1
2
3
3 4 5 21
6 7 8
2
1
1 ” (46 mm)
2
1
9 mm
x 3
”
(2.5 mm)
(35 ½” (902 mm))
” (1 mm)
” (5 mm)
”
(18 mm)
12 ¼” (311 mm)12 ¼” (311 mm)
16 ” (414 mm) X
- ”
(16 - 20 mm)
11 MOVE PRODUCT INTO CAVITY
13 ATTACH DRAWER PANEL TO FRONT OF DRAWER
Important!
Do not screw in trim
brackets at this stage.
Hook drawer panel onto
drawer front channel
Close the drawer and
check vertical clearances
Remove the panel and
adjust the TOP
attachment hooks
as necesary
Replace panel on
drawer and conrm
vertical clearances
Slide panel to achieve even
horizontal clearances
Open drawer and
clamp panel onto
drawer by tightening
the BOTTOM
attachment hook
Close the drawer and ensure it is ush
with adjacent cabinetry. If not, the
product may have to be pulled back
or forward.
Important!
Be careful not to damage power
supply cord when pushing
product into cavity.
12 FIT DRAWER PANEL ATTACHMENT HOOKS
Ensure there is clearance
between panel and cabinetry
when drawer is fully closed
Attach handle as necessary.
Ensure all screws are ush
with panel surface.
C is bottom face of panel to
top of internal shelf, see 6

3
2
” (4 mm)
1
” (2 mm)
1
2
14 SECURE TRIM BRACKETS TO CABINETRY
16 ATTACH FALSE PANEL
Important!
Ensure you check basic operation and perform
the nal checklist.
Attach the false panel securely
as recommended by the cabinet
maker.
Important!
The false panel needs to be removeable for
servicing.
15 ATTACH TRIMS TO SIDES OF CABINETRY
17 CHECK OPERATION
Open drawer and secure product
to cabinetry using four Trim
brackets and screws.

www.sherpaykel.com 840509 FRAMED CABINETRY 02.08
18 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Has all packaging been removed from the appliance?
Is the appliance securely fastened to the cabinetry?
Does the drawer slide freely and close properly?
Has the outlet duct been installed correctly?
Is the appliance level?
Are the panels securely attached?
Have the panels been properly aligned for correct operation and
appearance? Are all clearances even?
Is there clearance between drawer and cabinetry frame?
Has the power cord been plugged into a properly grounded 3-prong outlet,
which has been installed in accordance with all applicable electrical codes?
OPERATION:
Is the control panel lit?
Can you hear the compressor motor running?
When a hand is placed near the toe kick, can airow be felt under front
right-hand side of appliance?
Have you demonstrated the basic operation to the customer?
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER