iplex DVRMOB1 Installation instructions

DVRMOB1
I Channel DVR for SD Interface

2
1CH Mini DVR Full Manual V.1.0
GENERAL SAFETY AND PRECAUTIONS
This Mini DVR is manufactured to meet international safety standards. Review the following safety
precautions to avoid injury and prevent damage to the DVR or any products connected to it.
1. Use a correct power source. Do not connect this product to a power source that supplies more than
the specified voltage (DC12V), as this will cause damage to the unit.
2. Never insert anything metallic into the DVR as this can cause electric shock.
3. Do not operate in wet & dusty conditions. Keep product surfaces clean and dry. Avoid placing the
DVR in areas like a damp basement or a dusty hallway.
4. Do not expose this product to rain or use near water. If the product gets wet, unplug it and contact an
authorized dealer immediately.
5. To clean the outside case of the DVR, use a lightly dampened cloth (no solvents).
6. Do not operate if you suspected to unit is faulty. If there are any unusual sounds or smells coming
from the DVR, immediately unplug it and contact an authorized dealer or service centre.
7. Do not attempt to remove the top cover.
Warning: Removing the DVR’s cover can cause an electrical shock.
8. Handle DVR carefully to avoid damaging the product. Dropping your DVR on any hard surface may
cause the unit to malfunction. If the DVR doesn’t work properly due to physical damage, contact an
authorized dealer for repair or exchange.
9. The unit has a lithium battery preinstalled.
10. The standard lithium cell 3V battery located on the motherboard should be replaced if the time clock
does not hold its time after the power is turned off.

3
1CH Mini DVR Full Manual V.1.0
TABLE OF CONTENTS
Chapter 1: Packing Contents
CONTENTS IN THE PACKAGE 05
Chapter 2: Getting To Know Your DVR
1CH Mini DVR 06
Chapter 3: Remote control
REMOTE CONTROL PANEL 08
Chapter 4: Getting Started
OVERVIEW OF SET UP PROCEDURES 09
Chapter 5: Hardware Installation
SD MEMORY INSTALLATION 10
CONNECTING MINI DVR TO YOUR MONITOR OR TELEVISION 10
ALARM INSTALLATION 12
Chapter 6: DVR Menu
1. ACCESS TO OSD MENU 13
2. MAIN MENU 13
3. RECORD MODE 14
4. VIDEO QUALITY 14
5. EVENT MODE 15
6. SEARCH 17
7. SUB MENU 18

4
1CH Mini DVR Full Manual V.1.0
7.1 PASSWORD CHANGE
7.2 TIME SET
7.3 BRIGHTNESS
7.4 AUDIO
7.5 VIDEO
7.6 MEMORY SYNC
19
19
20
20
21
21
8. DEFAULT 22
Appendix:
TECHNICAL SPECIFICATIONS 23
RECORDING TIME TABLE RECORDING 24

5
1CH Mini DVR Full Manual V.1.0
Chapter 1: Packing Contents
▶Contents in the package
DVR Main Unit Remote Control AV-IN / AV-OUT Cable
Terminal Block 12V Power Supply Installation CD
Quick Guide SD Card (Option) USB SD Reader (Option)

6
1CH Mini DVR Full Manual V.1.0
Chapter 2: Getting To Know Your DVR
▶DVR
This chapter briefly describes the functions of each connection and LED on DVR. For more details on the
set-up and operation of , refer to Chapter 6, DVR MENU.
1Sensor-in / Alarm-out
Use the supplied terminal block to connect PIR type sensor to the DVR. By adding motion sensor
devices to your DVR, the video recording can be triggered by events.
The alarm output terminal will trigger a single external device.
2SD Memory Slot
①
②
③⑤
⑥
⑦
⑧⑨ ⑩
④

7
1CH Mini DVR Full Manual V.1.0
Insert SD Card into the data storage slot.
3Recording LED
This light indicates while DVR is recording.
4Status LED
This light flashes when an event or any error has occurred.
5Power LED
This light indicates when the DVR is powered up.
6Remote Control Receiver
The remote control must be pointing at the DVR and be in line of sight to work.
7Reset
Pressing the reset button will return the DVR setting to factory default.
8AV-IN
Connect AV-IN video / camera cable.
9 AV-OUT
Connect AV-OUT monitor cable.
10 Power
Connect 12V power supply.

8
1CH Mini DVR Full Manual V.1.0
Chapter 3: Remote control
1 REC: Starts DVR recording.
2
MENU: Enters the DVR ‘MENU’ mode.
3 UP/ DOWN buttons to chooses menu fields and changes values.
4 Plays recorded video forward. Plays recorded video backward.
5 REW: Fast Rewind button
6 FF: Fast forward button
7
PLAY: The button to start video playback.
8
STOP: The button to stop playback or recording.
9
PAUSE: The button to pause video playback.
10
MUTE: The button to pause audio.
11 ENT: The button to choose or change a menu option or values in a menu field.
12
SEARCH: The button to find recorded files in SD Memory.
13
MODE: The button to switch between playback and recording mode.

9
1CH Mini DVR Full Manual V.1.0
Chapter 4: Getting Started
OVERVIEW ON SET-UP PROCEDURES
Below is an overview of the MINI DVR installation procedures, (A detailed explanation is found in
Chapter 5 – Hardware Installation.)
(1) Insert a SD MEMORY.
(2) Connect the DVR to a monitor of television.
(3) Connect a camera to the DVR
(4) Connect optional accessories (sensors or alarm).
(6) Connect the power.
(7) Turn the power on.
(8) Start TV Monitoring and recording.
GeneralOperatingAdvice:
●Make sure that a SD Memory card is inserted and the camera is properly connected.
(See Chapter 5 -Hardware Installation)
●The firmware used in DVR is compatible with your computer’s operating system (i.e. Windows). Therefore,
you can take the SD memory card from this DVR and install it in your computer to view recorded video. (Refer
to the DVR Player manual.)
●DVR offers you the flexibility to choose a recording frame rate (maximum rate: 30 frames per second). The
faster frame rate the greater the SD Memory storage capacity required. Reducing the frame rate (minimum
rate: 1 frame per 10 seconds) will allow a greater recording duration.
●When connecting a camera is to DVR, the unit enters the default operational state: “VIEW mode”.
In this mode, DVR does not record nor play the recorded stream, but only shows the current images from the
camera.
●The default recording values for the DVR are 30 frames per second (25frames in PAL) with normal video
quality. If you use 1GB SD Memory, DVR can record for approximately 2 hours.
●If the power is inappropriately turned off while DVR is in the record mode (i.e. power failure), it will re-enter
the record mode automatically when power is re-established.
Refer to Chapter 5 - Hardware Installation for more information on installation procedures.

10
1CH Mini DVR Full Manual V.1.0
Chapter 5: Hardware Installation
SD MEMORY INSTALLATION
①Format SD Memory
Most SD cards are pre-formatted to FAT32. If not, insert the
card into the SD card slot on your PC and format it there.
※In case there is no card slot on your PC, use and external
card reading device.
②Insert SD Memory into SD slot
on DVR
After formatting, take the SD Memory card from your PC and
insert it into SD slot on DVR.
③Backup recorded files in SD Memory
When SD Memory storage is full, the recorded files can be
backed up in your PC. Insert SD card in your PC and move
the files of SD card into the HDD of our PC. You can also
check each recorded file through DVR Player.
※It is recommended that only SanDisk or Transcend SD cards are used, these are compatible with DVR.
※Be sure to turn off DVR first when you take out SD card from the slot.
CONNECTING DVR TO YOUR MONITOR OR TELEVISION
①Video Input/Output Connection (For monitor / TV screen display)

11
1CH Mini DVR Full Manual V.1.0
To display images from the DVR, connect the video output signal to your monitor or Television. Any
Television with a VIDEO INPUT terminal is suitable for displaying the images. The diagram above shows
the video signal connections.
Connect the camera to VIDEO-IN terminal of AV-IN using the supplied RCA cable; connect the VIDEO-
OUT terminal of AV-OUT to the VIDEO-IN terminal on your monitor using the supplied cable.
Note: The RCA cable required for this connection is not included in the package of DVR.
②Audio Input/Output Connection (For monitor / TV speaker)
Connect the microphone to AUDIO-IN terminal of AV-IN cable. And using RCA cable, connect the AUDIO-
OUT terminal of AV-OUT cable to AUDIO-IN terminal on your TV.
Note: The RCA cable required for this connection does not come packaged with the DVR.

12
1CH Mini DVR Full Manual V.1.0
ALARM INSTALLATION
When triggered by a sensor, the DVR will switch into record mode from standby mode; there is also an
internal switch for triggering an external buzzer.
Refer to the diagram below for information on how to connect an alarm to your DVR.
Note: Contact an authorized dealer for information about buying the appropriate alarm device and for
information concerning the correct installation procedures.

13
1CH Mini DVR Full Manual V.1.0
Chapter 6: DVR Menu
1. ACCESS TO OSD MENU
Press ‘MENU’ button on the remote control to access the DVR OSD menu.
Please refer to ‘Chapter 3: Remote control’ on how to use remote control buttons.
Default password is ‘0000’. To change the password; go to ‘[SUB MENU]Æ[PASSWORD CHANGE]’.
Use the up/down arrows on the remote control to adjust the numerical settings.
2. MAIN MENU
In the main menu, the ‘indicator ‘■’will be shown on the left of each menu.
Press the ‘UP/DOWN’ button on remote control to select the desired menu. After placing ‘■’on the desired menu,
press ‘ENTER’ to access the sub-menu.
Mini DVR
1.
0
* * * *

14
1CH Mini DVR Full Manual V.1.0
3. RECORD MODE
3. RECORD MODE
3.1 OVERWRITE (ON/OFF): If overwrite is set to ON, the DVR will continue recording while automatically
overwriting the oldest recorded files when SD memory storage capacity is full. Set to OFF, the recording will stop
when the SD Memory is full.
3.2 PRE ALARM (ON/OFF): Set to ON, the event recording starts several seconds prior to the actual event
triggered time. The alarm pre-recording time differs according to video quality setting.
4. VIDEO QUALITY

15
1CH Mini DVR Full Manual V.1.0
4.1 LEVEL (HIGH / NORMAL / LOW): Select desired video level.
Compression Bit rate for HIGH: 1.2Mbps
Compression Bit rate for Normal: 750Kbps
Compression Bit rate for Low: 500Kbps
4.2 POST RECORDING TIME: Post-recording time means is the recording time between the beginning and end
of an event. (1 sec to 30 mins)
4.3 FRAME RATE
NTSC: Selectable among 0.1 / 0.2 / 0.5 / 1 / 3 / 6 / 15 / 30
PAL: Selectable among 0.1 / 0.2 / 0.5 / 1 / 5 / 6 / 8 / 12.5 / 25
4.3.1 PRE RECORDING TIME
High: Up to 5 seconds of pre-recording available
Normal: 750Kbps / up to 8 seconds of pre-recording available
Low: 500Kbps / up to 10 seconds of pre-recording available
4.3.2 REMAINING MEMORY: This shows remaining storage capacity for further recording.
4.3.3 REMAINING TIME: This shows remaining time for further recording.
Note 1: 4.3.1 to 4.3.3 are entered automatically when video quality is set and cannot be changed.
Note 2: The higher the video quality, the better the image will be during playback.
The lower the video quality, the greater the record duration on the SD Memory Card.
Note 3: The video quality in View Mode is not affected by the video record quality settings.
These settings only affect the video quality during playback of recorded video.
5. EVENT MODE

16
1CH Mini DVR Full Manual V.1.0
5.1 ALARM SETUP
5.1.1 ALARM INPUT (ON / OFF): Select ‘ON’ if you want to use alarm input device.
5.1.2 TYPE: Select between ‘NO’ and ‘NC’ for the alarm input type.
NC: NORMAL CLOSE
NO: NORMAL OPEN
Note: In NORMAL-CLOSE mode, if an intruder cuts the cable that connects the sensor to the DVR, sensor
recording starts automatically. In NORMAL-OPEN mode, if an intruder cuts the cable that connects the sensor to
the DVR, will not start the sensor recording.
5.1.3 ALARM OUTPUT (ON / OFF): Select ‘ON’ if you want to use alarm output device
5.1.4 TYPE: Select between ‘NO’ and ‘NC’ for the alarm output type.
5.2 MOTION SETUP

17
1CH Mini DVR Full Manual V.1.0
5.2.1 MOTION (ON / OFF): Select ‘ON’ if you want to use motion detection.
5.2.2 SENSITIVITY (LOW / NORMAL / HIGH): You can select the degree of sensitivity of motion detection.
Set to HIGH for greater sensitivity to small movements.
5.2.3. MOTION MARK (ON / OFF): Select ‘ON’ if you want “Motion” to display on the monitor.
5.3 SCHEDULE SETUP
Schedule the recording time on this menu. Up to 4 schedules can be set. Configure period of time when
recording is available.
6. SEARCH
MON to FRI 00:00 ~ 09:00
MON to FRI 18:00 ~ 23:59
MON to FRI 00:00 ~ 09:00
OFF
2007 / 01 / 01 0 0 : 0 0
2007 / 01 / 31 2 3 : 5 9
SEARCH
TIME

18
1CH Mini DVR Full Manual V.1.0
After entering searching option in the fields, clicking ‘SEARCH’ will list the search results.
6.1 SEARCH METHOD: There are three ways to search recorded files; TIME, EVENT, BOTH (TIME & EVENT)
6.1.1 SEARCH MODE – TIME: Enter the time period you wish to search for.
6.1.2 SEARCH MODE – EVENT: When you select ‘EVENT (or BOTH) on SEARCH MODE’, additional search
conditions opens; ALARM / EMERG (Emergency) / MOTION
You can select 2 or more conditions simultaneously (ALARM / EMERG / MOTION).
6.1.3 SEARCH MODE – BOTH: Configure search condition as both ‘TIME’ and ‘EVENT’.
7. SUB MENU
To change a password, go to PASSWORD CHANGE in the SUB MENU and press [ENTER]. The following
screen will appear:

19
1CH Mini DVR Full Manual V.1.0
7.1 PASSWORD CHANGE
The Factory Default Password is 0000. To enter this number, press the UP/DOWN button on the remote control.
Once you input the your current password, set a new four digit password using the buttons UP, REW, DOWN,
FF on the remote control. Then, confirm your new password by entering the number again.
7.2 TIME SET
Configure current time and ‘day light saving’ option. On setting the current time, the field order should be as
follows;
2004/02/17 = year/month/day 19:44:32 = hour/minute/second
7.2.1 DAY LIGHT SAVING (ON/OFF): SELECT ‘ON’ when you want to use day light saving time. You can set up
a time of period when day light saving is applied.

20
1CH Mini DVR Full Manual V.1.0
7.3 BRIGHTNESS
Select brightness value between LOW, MEDIUM and HIGH.
7.4 AUDIO
Audio function can be turned OFF or ON in the menu.
Note: When recording audio, set the RECORD FRAMERATE to 5 or greater. If you set it under 5, audio
recording will not work.
ON