ICRealtime NVR 6000 Series User manual

NVR 6000 Series Quick Start Guide
V2.0.0

i
Table of Contents
1INSTALLATION AND CONNECTIONS ....................................................1
1.1 Check Unpacked NVR............................................................................................................1
1.2 Front Panel...............................................................................................................................1
1.3 Rear Panel................................................................................................................................2
1.4 Alarm Input and Output Connection .....................................................................................2
1.4.1 Alarm Input and Output Details.........................................................................................3
1.4.2 Alarm Input Port ..................................................................................................................3
1.4.3 Alarm Output Port ...............................................................................................................4
2OVERVIEW OF NAVIGATION AND CONTROLS ....................................5
2.1 Search & Playback ..................................................................................................................8
2.2 Network...................................................................................................................................12
2.2.1 Network Setting.................................................................................................................12
2.3 Remote Device ......................................................................................................................13
2.4 Manual Record.......................................................................................................................14
2.4.1 Manual record menu ........................................................................................................14
2.4.2 Basic operation .................................................................................................................14
2.4.3 Enable/disable record ......................................................................................................14
2.4.4 Enable all channel recording...........................................................................................14
2.4.5 Stop all channel recording...............................................................................................15
2.5 Shutdown................................................................................................................................16

ii
3SYSTEM UPGRADE ..............................................................................17
4WEB OPERATION .................................................................................18
4.1 General Introduction..............................................................................................................18
4.1.1 Preparation ........................................................................................................................18
4.2 Login........................................................................................................................................18
APPENDIX H TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS........21

iii
Welcome
Thank you for purchasing our NVR!
This quick start guide is designed to be a reference tool for the installation and operation
of your system.
Before installation and operation please read the following safeguards and warnings
carefully!
Please keep it for future reference!

iv
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
3．Installation
Keep upwards. Handle with care.
Do not apply power to the NVR before completing installation.
Do not place objects on the NVR.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted
repair.
5．Environment
The NVR should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
This series product shall be transported, storage and used in the specified environments.
6. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Name Quantity
Front panel key 2
HDD screws 68
Quick start guide 1
CD 1

1
1Installation and Connections
Note: All the installation and operations here should conform to your local electric safety
rules.
1.1 Check Unpacked NVR
When you receive the NVR from the forwarding agent, please check whether there is any
visible damage. The protective materials used for the package of the NVR can protect most
accidental clashes during transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list. Finally you can remove the protective film of
the NVR.
1.2 Front Panel
The front panel is shown as below. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for front panel button information.
SN Name Function
1 Power button Press it once to turn on the device.
Press it for a long time to turn off the device. (Usually we do not
recommend).
2 System HDD
Indication light
The blue light flashes when system is reading or writing the system
HDD.
In the system HDD, there are device important configuration file,
factory default configuration file, and device initial boot up data.
3 Alarm indication
light
The alarm indication light becomes on once an alarm occurred. The
alarm includes hardware alarm, network abnormal events, or system
receives the alarm signal and etc.
4 Network
indication light
The network indication light is blue and it flashes when you connect
the device to the network.
5 USB port /
6 Front panel lock /
After you remove the front panel, you can see there are 16 HDDs. From the left to the right and

2
from the top to the bottom, it ranges from 1~4, 5~8, 6~12, 13~16.
You can see there are two indication lights on the HDD bracket.
zThe power indication light is at the top. The light is yellow after you connected the device to
the power.
zThe read-write indication light is at the bottom. The blue light flashes when system is
reading or writing the data.
1.3 Rear Panel
The rear panel is shown as below. See Figure 1-2.
Figure 1-2
Please refer to the following sheet for detailed information.
SN Function SN Function
1 Power socket 6 Video VGA output
2 Audio Input 7 eSATA port
3 Audio output 8 USB port
4 Bidirectional talk input 9 HDMI port
5 Network port 10 Alarm input, alarm output, RS485 port.
1.4 Alarm Input and Output Connection
Please refer to the following sheet for alarm input and output connection.
There are two alarm input types for you to select: normal open (NO) and normal close (NC).
1. Alarm input
a. Please make sure alarm input mode is grounding alarm input.
b. Grounding signal is needed for alarm input.
c. Alarm input needs the low level voltage signal.
d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)
e. When you are connecting two NVRs or you are connecting one NVR and one other device,
please use a relay to separate them.
2. Alarm output
The alarm output port should not be connected to high power load directly (It shall be less than
1A) to avoid high current which may result in relay damage. Please use the co contactor to

3
realize the connection between the alarm output port and the load.
3. Please make sure the front-end device has soundly earthed.
Improper grounding may result in chip damage.
1.4.1 Alarm Input and Output Details
You can refer to the following sheet Xfor alarm input and output information. See Figure 1-3.
Figure 1-3
Please refer to the following sheet and Figure 1-3 for detailed information.
1，2，3，4，5，6，
7，8，9，10，11 ，
12，13，14，15，16
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
1-ON C，2- ON C，
3- ON C，4- ON C，
5- ON C，6- ON C，
7 - ON C，8- ON
Eight groups of normal open activation output (on/off button)
G GND cable.
485 A/B The A/B cable to control the RS485 devices. It is to connect to
control decoder such as the recorder.
Tx and Rx RS232 port. Tx is the data output cable and the Rx is the data input
cable.
1.4.2 Alarm Input Port
Please refer to the following sheet for more information.
zGrounding alarm inputs. Normal open or Normal close type)
zPlease parallel connect COM end and GND end of the alarm detector (Provide external
power to the alarm detector).
zPlease parallel connect the Ground of the NVR and the ground of the alarm detector.
zPlease connect the NC port of the alarm sensor to the NVR alarm input(ALARM)
zUse the same ground with that of NVR if you use external power to the alarm device.

4
Figure 1-4
1.4.3 Alarm Output Port
zProvide power to peripheral alarm device.
zTo avoid overloading, please read the following relay parameters sheet carefully.
zRS485 A/B cable is for the A/B cable of the PTZ decoder.
Relay Specification
Model: JRC-27F
Material of the
touch
Silver
Rated switch capacity 30VDC 2A, 125VAC 1A
Maximum switch power 125VA 160W
Maximum switch voltage 250VAC, 220VDC
Rating（Resista
n
Load）
Maximum switch currency 1A
Between touches with same
polarity 1000VAC 1minute
Between touches with different
polarity
1000VAC 1minute
Insulation
Between touch and winding 1000VAC 1minute
Surge voltage Between touches with same
polarity 1500V (10×160us)
Length of open
time
3ms max
Length of close
time
3ms max
Mechanical 50×106 times (3Hz)
Longevity
Electrical 200×103 times (0.5Hz)
Temperature -40℃~+70℃

5
2Overview of Navigation and Controls
Connect the device to the monitor and then connect a mouse and power cable. Click the power
button at the front panel and then boot up the device to view the analog video output. You can
use the mouse to implement some GUI operation.
Right click mouse, you can see system pops up the login interface for you to input user name
and password.
You can use USB mouse to input. Click to switch between numeral, English character
(small/capitalized) and denotation.
Note:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and six times login failure
will result in account lo
Figure 2-1
After device booted up, the system is in multiple-channel display mode. See Figure 2-2.Please
note the displayed window amount may vary. The following figure is for reference only.
Figure 2-2
You can overlay the corresponding date, time and channel name on each screen. You can refer
to the following sheet for channel record or alarm status information.

6
Navigation bar
The navigation bas is shown as below. See Figure 2-3.
Figure 2-3
①：Main interface
②：Output screen option:
Select corresponding output device and set the output window amount.
③：Window split:
System supports 1/4/8/9/16/25/36/64-window output mode. Please select the window mode
and then select the corresponding channels.
④：PTZ Setup
The PTZ setup is shown as in Figure 2-4.
Please note the commend name is grey once device does not support this function.
Double click the title to hide the PTZ menu interface.
Here you can control PTZ direction, speed, zoom, focus, iris, preset, tour, scan, pattern aux
function, light and wiper, rotation and etc.
Speed is to control PTZ movement speed. The value ranges from 1 to 8.The speed 8 is faster
than speed 1. You can use the remote control to click the small keyboard to set.
You can click and of the zoom, focus and iris to zoom in/out, definition and brightness.
The PTZ rotation supports 8 directions.
Figure 2-4
⑤：Record Search
It is a shortcut search menu. Please refer to chapter 2.4 for detailed information.
⑥：Alarm Info
The alarm information is shown as below. See Figure 2-5.
1 Recording status 3 Video loss
2 Motion detection 4 Monitor lock

7
It is for you to set the alarm information of current channel.
Figure 2-5
⑦：Network Setup
It is the shortcut network setup button. Please refer to chapter 2.2 for detailed information.
⑧：HDD management
It is the shortcut HDD management button. Please refer to 错误！未找到引用源。 for detailed
information.
⑨：Device management
You can use the channel list and the device list to manage the connected remote device. The
channel list is on the left. Here you can view all connected channel information. The green color
in front of the camera name means current channel is recording now. The grey color means
current channel is not recording. The device list is on the right. Here you can view connected
device information. Green icon means current device is online while the red cross means
current device is offline. See Figure 2-6.

8
Figure 2-6
2.1 Search & Playback
Click search button in the main menu, or you can right click mouse and then select the Search
item. Search interface is shown as below. See Figure 2-7.
Please note the initial version does not support smart search, card number search and
picture operation.

9
Figure 2-7
Please refer to the following sheet for more information.
SN Name Function
1 Display
window
zHere is to display the searched picture or file.
zSupport 1/4/9/16-window playback.
2 Search
type
zHere you can select to search the picture or the recorded
file.
zWhen there is displayed picture on the left pane, you can
set the corresponding setup
3 Calendar
zThe blue highlighted date means there is picture or file. Otherwise, there is no
picture or file.
zIn any play mode, click the date you want to see, you can see the corresponding
record file trace in the time bar.
4
Playback
mode
and
channel
selection
pane.
zPlayback mode：1/4/9/16. (It may vary due to different series.)
In 1-window playback mode: you can select 1-128 channels.
In 4-window playback mode: you can select 4 channels according to your
requirement such as channel 1-4,5-8…125-128.
In 9-window playback mode, you can switch between 1-8,9-16…121-128
channels.
In 16-window playback mode, you can switch between 1-16, 17-32…113-128
channels.
zThe time bar will change once you modify the playback mode or the channel
1
2
3
4
56
7
8
12 9
10
11

10
option.
5
File list
switch
button
zDouble click it, you can view the picture/record file list of current day.
zThe file list is to display the first channel of the record file.
zThe system can display max 128 files in one time. Use middle button of the mouse
to view the file. Select one item, and then double click the mouse or click the
ENTER button to playback.
zYou can input the period in the following interface to begin accurate search.
zFile type：R—regular record；A—external alarm record；M—Motion detect record.
6
Card
number
search
The card number search interface is shown as below.
►/
Play/Pause
There are three ways for you to begin playback.
zThe play button
zDouble click the valid period of the time bar.
zDouble click the item in the file list.
In slow play mode, click it to switch between play/pause.
■Stop button.
W
Backward play
In normal play mode, left click the button, the file begins backward play.
Click it again to pause current play.
In backward play mode, click ►/to restore normal play.
│W/
X│
In playback mode, click it to play the next or the previous section. You can
click continuously when you are watching the files from the same channel.
In normal play mode, when you pause current play, you can click W│and
│Xto begin frame by frame playback.
In frame by frame playback mode, click ►/to restore normal playback.
►Slow play
In playback mode, click it to realize various slow play modes such as slow
play 1, slow play 2, and etc.

Fast forward
In playback mode, click to realize various fast play modes such as fast
play 1,fast play 2 and etc.
Note: The actual play speed has relationship with the software version.
Smart search
The volume of the playback
7
Playback
control
pane.
Current series device does not support snapshoot function now.
8 Time bar zIt is to display the record type and its period in current search criteria.

11
zIn 4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
zUse the mouse to click one point of the color zone in the time bar, system begins
playback.
zThe time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are playing
the file.
zThe green color stands for the regular record file. The red color stands for the
external alarm record file. The yellow stands for the motion detect record file.
9 Time bar
unit
●The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger the
zoom rate. You can accurately set the time in the time bar to playback the record.
zThe time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are playing
the file.
10 Backup
Select the file(s) you want to backup from the file list. System max supports files
from four channels. Then click the backup button, now you can see the backup
menu. Click the start button to begin the backup operation.
Check the file again you can cancel current selection.
System max supports to display 32 files from one channel.
11 Clip
zIt is to edit the file.
zPlease play the file you want to edit and then click this button you can see the
time control. Select the start time and end time on the right side and click this
button again, you can see the backup data to be saved in the pop-up dialogue
box. Click this button again to exit the clip mode.
12 Record
type In any play mode, the time bar will change once you modify the search type.
13 Smart
search
zWhen system is playing, you can select a zone in the window to begin motion
detect. Click the motion detect button to begin play.
zCurrent button is null once the motion detect play has begun.
zThe system will take the whole play zone as the motion detect region by
default.
zThe motion detect play stopped once you switch the play file.
zOperations such as set time bar, click the play button, or any file list operation
will stop current motion detect play.
Other Functions
14 Digital zoom
When the system is in full-screen playback mode, left click
the mouse in the screen. Drag your mouse in the screen to
select a section and then left click mouse to realize digital
zoom. You can right click mouse to exit.
Note:
All the operations here (such as playback speed, channel, time and progress) have
relationship with hardware version. Some series NVRs do not support some functions or
playback speeds.

12
2.2 Network
Here is for you to input network information. See Figure 2-8.
zIP address: Here you can use up/down button (ST) or input the corresponding number to
input IP address. Then you can set the corresponding subnet mask the default gateway.
zDHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet
mask /Gateway. These values are from DHCP function. If you have not enabled DHCP
function, IP/Subnet mask/Gateway display as zero. You need to disable DHCP function to
view current IP information. Besides, when PPPoE is operating, you can not modify
IP/Subnet mask /Gateway.
zIP version: It supports IPv4.
zTCP port: Default value is 37777. You can change if necessary.
zUDP port: Default value is 37778. You can change if necessary.
zHTTP port: Default value is 80.
zRTSP port: Default value is 554.
Important: System needs to reboot after you changed and saved any setup of the above
four ports. Please make sure the port values here do not conflict.
zMax connection: system support maximal 20 users. 0 means there is no connection limit.
zPreferred DNS server: DNS server IP address.
zAlternate DNS server: DNS server alternate address.
zTransfer mode: Here you can select the priority between fluency/video qualities.
zLAN download: System can process the downloaded data first if you enable this function.
The download speed is 1.5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back to the previous
menu.
Figure 2-8
2.2.1 Network Setting
Network setting interface is shown as in Figure 2-9. Please draw a circle to enable

13
corresponding function and then double click current item to go to setup interface.
Figure 2-9
2.3 Remote Device
In the main menu, click the Remote Device icon to go to the corresponding interface.
The remote device interface is shown as in Figure 2-10.
zDevice search: Click it to search IP address.
zAdd: Click it to connect to the selected device and add it to the Added device list. Support
Batch add.
zShow filter: You can use it to display the specified devices from the added device.
zDelete: Please select one device in the Added device list and then click it to remove.
zManual add: Click it to add the IPC manually. The port number is 37777. The default user
name is admin and password is admin.
Figure 2-10

14
You can go to remote device information interface (Main menu->Info->Remote device info) to
view remote device information such as channel status, connection log, load balance and etc.
2.4 Manual Record
Note:
You need to have proper rights to implement the following operations. Please make sure the
HDD has been properly installed.
2.4.1 Manual record menu
Right click mouse or in the main menu, from Advanced->Manual Record, you can see
manual record menu is shown as in Figure 2-11. You can click the PgUp/PgDn button to
view more channels.
2.4.2 Basic operation
There are three statuses: schedule/manual/stop. Please highlight icon“○” to select
corresponding channel.
zManual: The highest priority. After manual setup, all selected channels will begin ordinary
recording.
zSchedule: Channel records as you have set in recording setup (Main
Menu->Setting->Schedule)
zStop: All channels stop recording.
Figure 2-11
2.4.3 Enable/disable record
Please check current channel status: “○” means it is not in recording status, “●” means it is
in recording status.
You can use mouse or direction key to highlight channel number. See Figure 2-12.
Figure 2-12
2.4.4 Enable all channel recording

15
Highlight ○below All, you can enable all channel recording.
zAll channel schedule record
Please highlight “ALL” after “Schedule”. See Figure 2-13.
When system is in schedule recording, all channels will record as you have previously set
(Main menu->Setting->Schedule).
The corresponding indication light in front panel will turn on.
Figure 2-13
zAll channel manual record
Please highlight “ALL”after “Manual.”See Figure 2-14.
When system is in manual recording, all scheduled set up you have set in will be null ((Main
menu->Setting->Schedule)).
You can see indication light in front panel turns on, system begins manual record now.
Figure 2-14
2.4.5 Stop all channel recording
Please highlight “ALL”after “Stop”. See Figure 2-15.
System stops all channel recording no matter what mode you have set in the menu (Main
menu->Setting->Schedule)
Figure 2-15